Modern wireless headphones from Xiaomi, in particular the Airdots Pro model, have become a popular choice thanks to excellent sound and active noise cancellation system. However, the process of initial synchronization with the device can raise questions for new users, especially if other brands have been used before.
Before starting the procedure, it is important to make sure that the case and the headphones themselves are charged, and the Bluetooth module is on on the smartphone. In this article, we will discuss in detail all the stages of connection, from extraction from the case to fine-tuning through a proprietary application.
The setup process takes only a few minutes, but requires attention to indicators and audio signals. We will look at the features of working with Android and iOS operating systems, as well as ways to solve common problems. If the device is not located or the sound is interrupted, read the relevant sections below.
Initial training Xiaomi Airdots Pro
Before you try to connect gadgets, you need to prepare them for operation in detection mode. Usually Xiaomi Airdots Pro go into pairing mode automatically as soon as you remove them from the charging case. However, additional actions may be required for the first activation after purchase or after resetting.
Make sure your headphones have a protective film removed from the charging contacts if they were there. This is critical, as blocking the contacts will prevent the device from knowing that it is extracted from the case.
💡
When you first turn on, leave the headphones in the case on charge for at least 30 minutes to activate the lithium polymer battery and calibrate the power controller.
There are two main start-up scenarios: connecting a new device and re-pairing. In the first case, the headphones will go into search mode themselves; in the second, you may need to manually start if you do not automatically connect to the last phone.
Step-by-step instructions for pairing with Android and iOS
The basic algorithm of actions is the same for most smartphones, but it has some nuances in the menu interface. First, remove both earbuds from the case, you will hear a voice message or an audible signal indicating that it is turned on, at which point the device is already available for search.
Open your smartphone settings and go to the Bluetooth section. Click on the scan button or Device Search. The list of available gadgets should appear as Xiaomi Airdots Pro or AirDots Pro. Click on it to start the procedure.
☑️ Quick connection algorithm
Once you've successfully connected, the phone's status bar will have a headphone battery icon, and if the system asks for code confirmation, just agree. It's important to keep the settings menu open until the Connected status comes next to the model name.
⚠️ Note: Do not remove the headphones from the case one at a time, otherwise the right and left channels may become desynchronized and work as two independent devices.
Setup through the Xiaomi Earbuds app
To unlock the full potential of Xiaomi Airdots Pro, a dedicated application is recommended: it allows you to control noise reduction modes, configure equalizers and update firmware. Without this software, many advanced features remain unavailable.
Download the Xiaomi Earbuds app from Google Play or the App Store. After installation, launch the program and click "Add Device." The app automatically finds the connected headphones and prompts them to be configured. The interface allows you to visualize the charge of each headphone separately.
The following key settings are available inside the application:
- 🎧 Switching noise reduction modes (ANC): transparent mode, active noise suppression, non-switching off mode.
- 🎛️ Sensory control setting: assigning double or triple touch actions.
- 🔊 Equalizer: Choice (pop, rock, classics) or manual frequency setting.
Why do you need a firmware update?
Regularly checking for updates in the application is a guarantee of stable operation. firmware 2.0 and higher significantly improves the stability of the connection in places with a large concentration of Wi-Fi networks. The update process takes about 5-10 minutes, during which the headphones cannot be used.
Mono mode and reconnecting one headphone
Often users want to use only one headphone, for example, for conversations or while driving. Xiaomi Airdots Pro supports mono mode, but require the right sequence of actions to activate it. Just removing one earphone in a case is not enough if the second continues to play music.
To go into single-earphone mode, first place both devices in the case and close it. Then take out just one earpiece. It has to automatically connect to the phone as a mono headset. If that doesn't happen, maybe there's a conflicting profile stored in the phone's memory.
To solve problems with channel desynchronization, follow the following steps:
- 📱 Remove the Xiaomi Airdots Pro from the Bluetooth list on your phone.
- 📦 Put both headphones in the case and close the lid.
- 🔄 Get both headphones out at the same time and wait for their mutual pairing (blinking indicators).
- 🔗 Perform re-pairing with the smartphone.
If one earphone is discharged faster than the other, the system may not turn on stereo immediately after charging, and allow both devices to lie in a case for 5-10 minutes to equalize the charge before use.
Table of indicators and their significance
Understanding the color indication of LEDs on the headphone case and case helps diagnose the condition of the device without connecting to the phone. Different colors and blinking modes report specific processes.
| Indicator | Color/Mode | Meaning |
|---|---|---|
| Headphone (inside the ear) | White (constantly) | The headphone is connected and ready to go |
| Headphone (inside the ear) | Red (constantly) | Low battery charge, charging required |
| Headphone (inside the ear) | White (blinks) | Interconnection mode (search for device) |
| Case (inside) | Orange | Headphone charging is in progress |
| Case (inside) | Green. | Headphones fully charged |
Note that the brightness of the indicators can vary depending on the angle of view. If the indicator does not light up at all, wipe the contacts with dry cloth - oxidation or dust can block the signal.
The solution: why the phone can't see headphones
It's rare for a smartphone to not detect the Xiaomi Airdots Pro, but it has a logical explanation. Most often, the problem is that the headphones are already connected to another device or are in sleep mode. Check the Bluetooth list on all gadgets within range.
Another reason could be the overflowing Bluetooth memory in the phone: If there are many old devices on the list, the new gadget may not be added, delete unused profiles and try again.
⚠️ Warning: If the headphones were previously paired with another phone, they may automatically try to connect to it, ignoring your new request.
In rare cases, a full reset of headphones helps, so put them in a case, open the lid, and press the touch zones on both headphones simultaneously, holding for about 5-10 seconds until the indicators flash red, which will return them to factory settings.
💡
If standard methods don’t work, a full reset by retaining the Senor solves 90% of the invisibility problems.
Optimizing the quality of sound and codecs
The quality of music playback depends on the codec used. Xiaomi Airdots Pro supports the AAC codec, which provides good quality on iOS devices and most Android smartphones. Check the activated codec in the developer settings or in a special application.
To improve the sound, you should also check the equalizer settings in the player or system equalizer. Avoid excessive bass amplification, as this can lead to distortions at high volume. The optimal setting is a slight rise in low and high frequencies.
Remember, distance to the source of the sound and the presence of obstacles affect the stability of the connection. In Bluetooth 5.0 mode, the range is up to 10 meters in open space, but walls can significantly reduce it.