Owners of wireless headsets often face a situation where Xiaomi Mi True Wireless Earphones stop responding correctly to commands, lose sync or simply refuse to turn on. In such cases, a standard shutdown is not enough, and a deeper intervention in the operation of the device's software is required. Reboot allows you to clear the temporary cache of the Bluetooth module and eliminate software failures that accumulate during operation.
Many users confuse a conventional power outage with a full system reboot, which leads to erroneous actions. It is important to understand the difference between soft reset and hard reset, since these procedures have different consequences for stored data and pairing profiles. In this article, we will discuss in detail all available methods for restoring the health of your headphones.
Modern models, such as the Mi True Wireless Earphones 2 Pro or Redmi Buds 3 Pro, are equipped with a complex firmware that controls noise cancellation and codecs. A failure in this system can lead to desynchronization of the left and right channel, when sound comes from only one earphone. A properly executed reboot often solves this problem without going to the service center.
Before you start taking radical measures, it's worth trying the simplest and safest recovery method, which doesn't require special tools or long wait times, and it usually works in 80% of cases where the device just freezes and doesn't respond to touch.
To perform a soft reboot, you need to place both headphones in a charging case. Make sure the case is connected to a power source or has sufficient battery power. Leave the devices in a closed case for 10-15 minutes. During this time, the power controller inside the case will force the headphone modules to de-energize, and then give a signal to start, which is equivalent to restarting.
If the headphones are outside the case and are frozen, you can try to force the switch off. To do this, press the touch zones on both headphones simultaneously and hold them for 20-30 seconds. The indicators should flash red to signal the shutdown, after which the device can be activated again with a short press.
💡
If the headphones do not respond to touch, try first to completely discharge them, leaving them out of the case for a few hours, and then put on a charge to turn on.
Sometimes a simple reboot is not enough and you need to clear the list of conjugated devices. This is especially true if you have changed your smartphone or headphones connect to someone else's device within range. Resetting Bluetooth settings will return the gadget to a "store-like" state.
Hard Reset is performed on most Xiaomi Mi models via a charge case. Place the headphones in the case, but don't close the lid. Find the function button on the case (usually located on the side or between the headphone compartments). Press and hold this button for 15-20 seconds.
Watch the status indicator on the front of the case, it will flash white, then go into rapid blinking mode in orange or red, which means that the reset process is started. Release the button only after the indicator changes the pattern of glow.
☑️ Checklist for a complete reset of headphones
Once the reset is successful, the headphones will automatically go into pairing mode. On your smartphone, you need to go to the Bluetooth settings, find the old record of your headphones, and select the option “Forget the device” or “Disable” before you can perform a new search and connection.
There are a number of specific problems that may arise after a reboot or require a special approach, such as desynchronization of a stereo pair, where one earphone plays music and the other is silent, in which case the reset procedure should be performed especially carefully.
To resynchronize the channels, reset the settings as described above, but make sure both earbuds are in the case at the time of pressing the button. After reset, remove both earbuds at the same time. They should quickly find each other, and only one of them (usually the right one) will be visible in the Bluetooth list.
⚠️ If after resetting the headphones continue to work only in mono mode, try to repeat the procedure, having previously completely discharged the case and headphones to zero.
Another common problem is the quiet sound or lack of sound in one of the channels after updating the firmware of the smartphone, in which case the reboot of the headphones often resolves the codec conflict, and it is also worth checking the sound balance in the accessibility settings of your phone.
Why don't the headphones drop?
Different Xiaomi headphone models may have slight differences in management, and below is a table that will help you determine the right sequence of actions for popular models.
| Model headphones | Resetting method | Indication of success | Retention time |
|---|---|---|---|
| Mi True Wireless Earphones 2 | The button on the case | Blinking white 2 times | 15 seconds. |
| Redmi AirDots 2 | 5 Quick Presses on the Sensor | Voice message | Fast rhythm. |
| Mi True Wireless Earphones Pro | The button on the case | Orange blinking | 20 seconds. |
| Redmi Buds 3 Lite | Touch control 5 times | Sound signal | For 5 seconds. |
Users often wonder if it is possible to reboot the headphones without using a case. For most TWS (True Wireless Stereo) models, this is not possible, since the control button and the power controller are located in the case. However, for some models with touch control, there is a combination of touches.
Try tapping the touchpads of both headphones 5 times quickly and rhythmically. If the model supports this feature, you will hear voice confirmation or see a specific flash of indicators. This method does not work on all devices and is more the exception than the rule.
This can be battery wear, damage to contact areas in the case or conflict Bluetooth versions on the smartphone.
If none of these methods worked, it's worth checking the contacts. Wipe the golden contacts on your headphones and inside your case with a dry, lilaless cloth or cotton swab slightly moistened with alcohol. Oxidation of the contacts often causes the headphones to not charge or reboot in the case.
⚠️ Note: Do not use wet wipes with lotion or soap to clean contacts, as residues of the chemical can cause corrosion and short circuiting.
In some cases, the problem is not with the headphones themselves, but with the smartphone. The overflowing cache of Bluetooth services on Android can interfere with the correct operation of new connections. Cleaning the Bluetooth cache in the phone settings often works wonders.
To do this, go to Settings → Applications → Show system processes → Bluetooth → Memory → Clear the cache. After this operation, the phone will re-scan the ether and establish a more stable connection to the headset.
💡
A comprehensive approach (earphone reset + phone cache cleaning) solves 95% of connectivity and sound problems.
To sum up, the Xiaomi Mi headphone reboot is a simple but powerful tool to solve most technical problems, and the key is to follow instructions consistently and not panic if you don’t get the result the first time.
Regular maintenance of the device, including cleaning contacts and timely update of firmware through the Xiaomi Earbuds app, will avoid the need for frequent resets. Careful attitude to electronics prolongs its life and guarantees high-quality sound.