Modern wireless gadgets such as Xiaomi Mi True Wireless 2 are complex electronic devices that, like smartphones, require a forced system restart from time to time. Users often face situations where one of the headphones stops syncing with the other, the sound becomes intermittent or the phone does not see the headset at all in the list of available Bluetooth devices.
The routinely referred to as “reset” is technically a factory reset or Hard Reset, which clears the modules’ internal memory of accumulated pairing errors and puts them back in a “out of the box” state. Understanding the differences between a simple power outage and a software reset is critical to properly restoring your audio system to work without going to a service center.
In this guide, we will discuss in detail all available methods of resuscitation of headphones Mi True Wireless 2 and Mi True Wireless 2S. We will look at standard methods through touch panels, alternative methods using a charging case, and also analyze the typical errors that users make when trying to restore connection. Following the instructions will help avoid damage to the firmware and ensure a long life for your gadgets.
Diagnosis: When a forced restart is required
Before taking action, it is necessary to clearly define the nature of the malfunction. Often users try to reset when the problem lies in a discharged battery or contamination of contacts. Forced reboot is necessary in cases where there is a desynchronization of channels (only one earphone plays), when the device is seen by the phone but does not connect, or when the indicators behave unpredictably.
If you notice that the video delay has become noticeable, or the voice assistant has stopped responding to commands, this can also be a sign of a software failure in the Bluetooth module. Unlike mechanical failures, such glitches are often temporary and are eliminated by cleaning the memory buffer. However, if the problem persists after several attempts to reset, it may be the hardware.
It is important to distinguish between a software failure and a physical injury. If the earphone fell into the water or suffered a severe impact, software methods may not help. In normal situations, when the device simply “gone out”, restarting the system is the first and most effective step. Do not ignore repeated connection errors, as they can signal the need to update the firmware through the Xiaomi Earbuds application.
Preparation for the resetting procedure
The success of the recovery operation depends on proper preparation. The first and most important condition is that the charge is in the headphones themselves and in the charging case. If the energy level is critically low, the device may turn off during the reset process, which will lead to improper operation or complete lockdown. Put the headphones in the case and let them charge for at least 15-20 minutes before the manipulation begins.
The second important step is to remove the old pairing profile, so that the reset is clean, you have to forget the device in your smartphone settings, which ensures that once you reboot, the phone will perceive the headphones as new without trying to apply the old, possibly erroneous connection configurations, and ignoring this step is the most common reason why resets don't work the first time.
☑️ Checklist before reset
It is also recommended to check the purity of the charging contacts, they should not be oxides, dust or pile from the fabric, as this can prevent the correct transmission of control signals from the case to the headphones during the procedure. Use a dry cotton swab or microfiber to carefully clean the metal areas inside the recess of the case.
Method 1: Classic reset through touch panels
The main and most commonly used way to reboot Xiaomi Mi True Wireless 2 involves using touch zones on the headphones themselves. This method does not require a charging case at hand, which makes it convenient to use on the road. However, it requires a certain skill and accurate timing of the presses, since the sensors are sensitive to the duration of the touch.
First, remove both earbuds from the charger case. Make sure they're on (usually they turn on automatically when you retrieve them). If the lights are on or flashing, then the device is ready to go. Now you need to touch the touch areas on both headphones at the same time. Depending on the firmware version, the algorithm may vary slightly, but the basic principle remains the same for the True Wireless 2 series.
⚠️ Attention: Don't put too much physical effort into pressing. Touch panels respond to touch, not pressure. Strong indentation can damage the speaker's inner membrane.
The pattern is this: press and hold your fingers on the touch areas of both headphones simultaneously for about 5 seconds. The headphones should turn off (the indicators will go out). After that, without letting your fingers go off (or pressing them again if they turn off), hold the sensors for about 15-20 seconds. At some point you will see the indicators light up, then go out and blink again, often changing color or blinking mode. This is a signal that Hard Reset is successful, and the headphones went into search mode (mating).
What to do if the timing does not match?
Method 2: Reboot using a charging case
If touch panel manipulation fails, an alternative method that uses the logic of the charging case is particularly effective when one of the headphones is stuck and does not respond to touch. Place both earphones in the charging case and close the lid.
Let them lie closed for about 10 seconds, so they're guaranteed to go into charge mode and turn off. Then open the case lid, but don't take the headphones out. At this point, some versions of the firmware start automatically reconnecting with each other. If that doesn't happen, remove the headphones from the case at the same time.
There is also a cyclic charging method that helps reset the power controller: Put the headphones in the case, close the lid, wait 5 seconds, open and immediately remove. Repeat this procedure 3-4 times in a row, which can trigger a reboot of the internal power controller, which often solves the problem of a dead earphone that does not turn on.
💡
When using the case method, make sure the lid closes before the characteristic click of the magnet. If the lid is opened a little, the headphones may not go into deep sleep mode and reset will not occur.
Table of indicators and their value when discharged
Understanding LED signals is key to successful diagnosis. During the reboot procedure, the LEDs on the Mi True Wireless 2 headphones change their mode of operation. Below is a transcript of the basic states that will help you understand where the process is.
| Indicator mode | Colour | Significance of state | User action |
|---|---|---|---|
| It's burning all the time. | White | Normal work / Charging completed | Headphone ready for use |
| Blinks fast. | White | Search mode (Pairing Mode) | Search for the device in the Bluetooth menu of the phone |
| Blinks slowly | Red. | Low battery charge | Put it on charge immediately. |
| It's flashing and going out. | White/Red | Resetting/Resetting process | Release sensors, wait for completion |
Note that when you run Hard Reset, the indicators can be chaotic, flashing different colors quickly or lighting up sequentially, which is a normal response of the system to the memory clear command, and the main thing is to wait until both earbuds go into fast white blinking mode, which means that you are ready for a new pairing.
Common Errors and How to Resolve Them
Even following the instructions, users sometimes find that the desired result is not achieved. One of the most common mistakes is the late release of touch panels. If you release your fingers early, the reset process will stop, and the headphones will simply turn off or turn on as usual, you need to maintain a pause in retention until the nature of the flashing indicator changes.
Another common problem is trying to reset just one headphone. True Wireless is designed so that the left and right channels need to be synchronized. Resetting just one will cause them to become out of sync, and they won't "see" each other. Always do the procedure for both modules at the same time, or use a case to initialize them together.
💡
Synchronicity is key to success, and all the manipulation of sensors or cases must be done simultaneously for the left and right earphones, otherwise they will lose communication with each other.
⚠️ Note: If the headphones are seen as two separate devices by the phone after reset (e.g., "Mi True Wireless 2" and "Mi True Wireless 2 R"), they have not paired with each other.
Also worth mentioning is the influence of third-party factors: Having many other active Bluetooth devices nearby can cause interference during the initial pairing after reset, and try to perform the procedure away from powerful radiation sources or other active headsets.