Xiaomi Mi Robot Vacuum Mop P: How to turn on wet cleaning

Modern robot vacuum cleaners are no longer just carpet dust collectors. Xiaomi Mi Robot Vacuum Mop P is an advanced system that can keep floors clean in a complex way, combining dry cleaning and washing. Many users are faced with the question of why the device simply drives around the house ignoring a rag and do not know where to activate the wash function. The answer lies not in one button, but in the right sequence of actions and software configuration.

To get started, you need to understand the physical design of the device. Unlike some competitors, which have software-switched modes, it requires the mechanical installation of a special module. Wet cleaning will only become available after you physically replace the main dust collector with a combined water tank. Without this step, the software can block the launch of the corresponding algorithms for movement and water supply.

It is also important to consider that the process is controlled mainly through the mobile application Mi Home. the interface of the robot on the body is minimalistic and does not allow you to adjust the water intensity or select the “carpet” mode in detail. Therefore, connecting to the Wi-Fi network and linking to the account are mandatory conditions for the full use of all the functions put by Xiaomi engineers in this model.

Preparation of equipment and installation of a water tank

The first and most important step is to properly prepare the washing module. The robot comes with a special combined tank that combines the functions of a dust container and a water tank. You need to remove a standard dust collector, if installed, and prepare a module with water. Note that using ordinary tap water can eventually lead to the formation of scale in a pump, so it is recommended to use filtered or distilled water to extend the life of the device.

The installation process requires care so that the electronic contacts are not damaged. First, open the tank lid and pour water to the maximum point, avoiding overflow. Then close the valve tightly and make sure the rubber gasket is fixed evenly. Then insert the module into the robot compartment until the characteristic click. If the tank is installed incorrectly, the sensors may not count its presence, and the washing function is not activated.

• 💧 Remove the main dust container by opening the top cover of the robot body.
• 💧 Unscrew the water tank lid and fill it with clean water without exceeding the mark MAX.
• 💧 Make sure the microfiber wipe is clean and properly secured on the plastic platform of the tank.
• 💧 Insert the module into the robot before clicking and close the top cover of the device.

Once the module is physically installed, the device must beep to confirm that the new component has been successfully connected. In some cases, the robot needs to be rebooted: press and hold the power button on the body for a few seconds, which is necessary for the controller to reallocate resources and activate the humidity control algorithms.

⚠️ Warning: Never run a robot with a water tank installed on long-pile carpets without first setting up the app.This can cause the coating to get wet and mold to appear inside the pile.

Setting up parameters in the Mi Home app

Physical installation of the tank is only half the battle. The basic logic of the Xiaomi Mi Robot Vacuum Mop P is tied to software settings. To access them, open the Mi Home app on your smartphone and go to your device card. If you see only the start button but no cleaning settings, check if the region in your account profile is correctly selected (often switching to China or the country of purchase of the device helps).

You have to find a point in the control interface that controls the cleaning modes, usually indicated by a water drop icon or the signature "Cleaning settings," and you have to choose from three levels of water intensity: low, medium or high, depending on the type of flooring, medium or linoleum, and maximum for highly contaminated areas.

Special attention should be paid to the functions of carpet recognition. Xiaomi Mi Robot Vacuum Mop P is equipped with sensors that allow you to determine carpeting. In the settings, you can activate the mode in which the robot will either bypass the carpets, raise the water supply module (if the design allows) or simply stop the fluid supply. This is a critical setting for mixed floor types.

• 📱 Open the Mi Home app and select your robot vacuum cleaner.
• 📱 Go to the settings menu (three dots in the corner) and select “Cleaning Settings».
• 📱 Activate the “Use Water Tank” slider or similar switch.
• 📱 Set the desired water supply level and mode of operation with carpets.

After making the adjustments, it is recommended to run a short test cleaning in a limited area, which will allow you to assess how well the floor is moisturized and whether the robot leaves unnecessarily wet marks. Remember that the intensity of the water supply affects not only the quality of the washing, but also the battery life of the device.

Starting cleaning and choosing operating modes

When the equipment is ready and the settings are saved, you can start directly. You can control the robot in several ways: through voice commands (if you have a smart home connected), through an application or using buttons on the case. However, for the first time wet cleaning is turned on, you better use the application to monitor the process in real time.

The main menu of the app offers different scenarios: the most common way to wash floors is to use the “Wet Clean Only” mode or the combined “Sweep and Wash” mode. The first option is preferable if the floor is already pre-cleaned of large debris. The second option is universal, but requires regular brushing so that wet dirt does not wind up on the shaft.

You can also set up a schedule, you can set up a wet cleaning routine on certain days of the week and at certain times, which is convenient when you're not at home, so you don't have to worry about noise or discomfort from moving equipment, but when you first set up, you'd better be there to monitor the system.

Importantly, when the wash mode is activated, the robot can change its trajectory, and the mapping algorithm can switch from zigzag motion to along and across motion for more thorough surface treatment, which is normal behavior, indicating that intelligent navigation is working correctly.

Technical features and calibration of water supply

The Xiaomi Mi Robot Vacuum Mop P is electronically controlled, meaning that water is delivered by pump-dose rather than flowing by chance, and allows the wipe to be moistened evenly throughout the cleaning process, avoiding the wet start and dry finish effects of gravity systems.

But like any mechanism, the pump needs to be calibrated correctly. If you notice that the floor is dry even at maximum settings, there may be a traffic jam in the system. There's a special procedure to fix it: remove the tank, press the start button on the robot (with the tank installed) to make the pump work, and wait for the drops on the napkin to appear.

The accuracy of the dosing also depends on the quality of the napkin itself. Original microfiber fabrics have a certain pile density that is optimal for capillary moisture distribution. Using cheap analogues or rags made from other materials can upset the balance of the water supply, which will lead to either puddles or inefficient washing.

⚠️ Warning: Do not add detergents, chlorine or flavors to the water tank. Aggressive chemicals can eat up pump seals and plastic parts of the tank, leading to breakage and loss of warranty.

💡

To improve the quality of washing, add a cap to the water of a special tool for robotic washers, if the manufacturer allows this in the instructions, or use only clean water for electronic safety.

Wet cleaning system care and maintenance

Regular maintenance is the key to the long service of your Xiaomi Mi Robot Vacuum Mop P. After every wet cleaning, you need to remove the tank, drain the remaining water and thoroughly wash it. Stagnant water is the ideal environment for bacteria to multiply and the appearance of an unpleasant musty smell that will spread throughout the house during work.

A microfiber wipe should be washed after each use. Machine washing at a temperature of no more than 40 degrees without using underwear conditioners will help restore the absorbent properties of the fabric. Air conditioners create a fat film on the fibers, which stops the fabric from absorbing water and starts simply smearing dirt on the floor.

Once a month, a preventive pump outlet cleaning is recommended, using a soft toothbrush or cotton swab dipped in water to remove possible mineral deposits, especially if you use hard tap water without prior filtration.

• 🧼 After cleaning, be sure to drain the remaining water from the tank.
• 🧼 Take off the napkin and wash it separately from other clothes.
• 🧼 Wipe the contacts on the tank and in the robot with dry cloth to avoid oxidation.
• 🧼 Check the filter once a month. HEPA humidity.

And don't forget the fine filter. Although the main airflow is through the dust collector, when wet cleaning, the humidity in the case can increase. If the filter gets wet, it will lose its properties and can cause engine failure. Always make sure that the filter is dry before installing the main dust collector after the wash mode.

💡

Timely drying of all components of the tank and regular washing of the wipe prevent the appearance of odors and bacteria, keeping the efficiency of cleaning at a high level.

Solving typical problems and malfunctions

Even when properly operated, users can face a number of common problems: One of the most common is that the robot reports that there is no water tank, even though it is installed. Most often it involves contamination of the contact group or displacement of the sensor. Wipe the contacts with an alcohol wipe and make sure that the tank is inserted to the point.

Another common problem is uneven moisture or puddles, which may indicate a pump malfunction or clogging of the outlet. Also check the density of the napkin: if it dangles or has folds, the water will be distributed by stains, and in some cases, replacing the napkin attachment platform itself, if it is deformed, helps.

If the robot started leaving dry stripes in the middle of the wet area, it may have run out of water in the tank early because of improper level calibration or using too absorbent (but inappropriate) fabric.The application may display full battery charge, but the actual energy consumption when running the pump is higher, which is also worth considering.