Modern robot vacuum cleaners have long ceased to be just devices for collecting dust, becoming full assistants able to maintain the cleanliness of the floor without your participation. Xiaomi Vacuum Mop is a vivid example of such a versatile technique that combines powerful suction and wet wipe function. However, in order for the device to work correctly and not damage the flooring, you need to properly configure and start the wet mode.
Many users have difficulty with their first use, not understanding the difference between dry cleaning and washing, or not knowing how to activate the water supply through the app. Mistakes at this stage can lead to puddles or, conversely, to the operation of a dry tank vacuum cleaner. In this article, we will discuss the entire preparation and start process in detail so that you can enjoy a perfectly clean floor.
Preparation of the reservoir and installation of a water supply system
The first and most important step is to physically prepare the combined container, which is responsible for collecting dust and simultaneously supplying water. Unlike conventional models, it uses a special electronic tank that requires pre-activation before starting, and if you just pour water, the system will not start working, because the pump will not receive a signal to turn on.
You need to remove the container from the robot body and disconnect the garbage collection compartment, if it is installed. At the bottom of the water tank is a valve that you need to open. Most Xiaomi models have a special lever or button that you need to hold for a few seconds. After opening the valve, pour clean water at room temperature to the maximum mark.
Do not use hot water or aggressive chemicals, as this can damage the seals and membrane pump. It is allowed to add special detergents for robotic systems, but strictly in the recommended proportions. Once filled, close the lid tightly and make sure that the valve is closed to avoid leaks during installation.
- 💧 Open the water supply valve and fill the reservoir with clean liquid to a level MAX.
- 🔒 Close the tank cover tightly and check the tightness of the connections before installation.
- 🧹 Install a microfiber wipe on the platform, making sure that it is securely fixed with Velcros.
- 🔋 Make sure that the robot is at least 20% charged before a long cleaning.
⚠️ Warning: Never leave water in the tank for long after cleaning. Stagnant water can cause mold inside the pump system and cause an unpleasant odor that will spread throughout the apartment at the next start.
Once the tank is filled, gently insert it into the robot body before the characteristic click, at which point the device is ready for software setup, which is done via the smartphone. Without the correct configuration in the application, the robot can ignore the command to supply water.
Setting up washing parameters in the Mi Home application
To manage all the functions of Xiaomi Vacuum Mop, you need to use the official Mi Home or Xiaomi Home app. After connecting the robot to the Wi-Fi network and adding it to the list of devices, go to the main control screen. This is where the device's behavior during wet cleaning is finely adjusted.
In the app interface, find the section that is responsible for the type of cleaning. You will be asked to choose between dry cleaning, wet cleaning or combined mode. To activate the water supply, select the option “Wet cleaning” or “Mop.” In some versions of the firmware, this option is called Water Flow.
Pay special attention to the water level adjustment. The system allows you to adjust the intensity of moisture of the cloth, which is critical for different types of flooring. Laminate and parquet require a minimum flow to avoid swelling of the wood, while for porcelain porcelain you can set an average or high value.
- 📱 Open the Mi Home app and select your robot vacuum cleaner from the device list.
- 🌊 Go to the cleaning settings and select Wet Cleaning or Water mode. + vacuumer».
- 🎚️ Adjust the water supply level (low, medium, high) depending on the type of gender.
- 🗺️ If necessary, set up virtual walls to limit the washing area.
You can also activate automatic return to base for water refueling if the model supports this option, or simply to replace water, and make sure that the map settings do not set a no-go zone for this type of cleaning, otherwise the robot will simply pass by the contaminated area.
💡
For carpets, always set the “Carpet Only” mode or lift the platform with a cloth if the model allows it to avoid getting wet.
Starting cleaning and monitoring the process
Once all the parameters are set, you can go directly to start the device, and you can initiate the process through both the app on your smartphone and voice commands if the robot is connected to the smart home (Google Assistant, Alice, Siri). Pressing the Start button in the app sends a command to start work.
In the first minutes of operation, the robot will scan the room and build a route. In wet cleaning mode, it will move more slowly and methodically, usually along parallel lines to ensure uniform moisture of the floor. On the smartphone screen, you will see the status of "Water supply" or the corresponding icon.
Monitor the first 5-10 minutes of work to make sure the water supply is correct. Swipe your finger across the floor behind the robot: if there is a barely noticeable wet trail that dries quickly, then the setting is done correctly. If the water is flowing in a stream or the floor remains dry, you urgently need to stop the device and recheck the valve settings and level in the application.
Sequence of actions for launch:
1. Check the charge level (>20%).
2. to make sure there is water in the tank.
3. Open the Mi Home app.
Select "Water" or "Wet cleaning" mode.
5. Press the Start button.⚠️ Warning: If you notice that the robot is leaving puddles, stop cleaning immediately.This may indicate a valve malfunction or too high a water supply level for this type of coating, which can lead to soil damage.
Table of working hours and intensity
Understanding the differences between modes will help you better harness the potential of the device. Different scenarios require different cleaning approaches, and the Xiaomi Vacuum Mop offers flexible customizations for each case.
| Regime. | Description | Water intensity | For which surfaces |
|---|---|---|---|
| Quiet | Minimum noise, energy savings | Low. | Laminate, flooring, night |
| Standard | Balance between noise and efficiency | Medium | Linoleum, tiles, daily cleaning |
| turbo | Maximum suction and delivery | Tall. | Porcelain, heavy pollution |
| MAX | Maximum power for complex tasks | Maximum | Kitchen, hallway, technical areas |
When choosing Turbo or MAX mode, remember that water and energy consumption increases significantly, battery life in such modes can be reduced by 30-40% compared to standard dry cleaning, so for large areas, it is recommended to use standard settings.
What to do if the robot is stuck during wet cleaning?
System maintenance after completion of the cycle
Finishing the robot isn't the end of the maintenance process. Proper care after each wet cleaning extends the life of the device and ensures the quality of the next wash. The residue of water in the tank and the dirt on the cloth require your attention.
Immediately after you return to base, remove the combined container. Pour the remaining water, even if the tank is not empty. Then rinse the tank with clean water and let it dry. Pay special attention to the microfiber wipe: it must be removed, rinsed from the dirt and dried.
Check the status of the electrodes in the tank regularly (if the model is equipped with a water level sensor), they can accumulate scale, especially if you use hard water, clean with a soft brush or a special scale repellent, but you need to do this carefully so as not to damage the contacts.
- 🚫 Always drain the remaining water from the tank after cleaning is complete.
- 🧼 Remove and wash the microfiber wipe after each use.
- 🌬️ Dry all removable parts of the tank in disassembled form in the open air.
- 🔍 Wipe the charging contacts on the robot and base with a dry cloth.
☑️ Post-treatment after cleaning
Addressing common problems
Even with the right setup, there can be situations where the system is not working properly, most often problems are due to software failures or physical obstacles, and if the robot is not supplying water, check if the feed channel is clogged.
Sometimes it helps to simply reset or restart the device, turn off the robot with the power button, wait 10 seconds and turn it on again, and if the problem persists, try re-activating the tank by opening and closing the valve.
It's important to keep the floor sensors clean. If they're contaminated, the robot can "think" it's on the carpet or the stairs, and block the water supply for safety. Rubbing the sensors with a soft dry wipe often solves the problem of false positives.
💡
Regular prevention and timely cleaning of filters and sensors prevent 90% of possible malfunctions of the wet cleaning system.