Modern technology owners often face the first challenges of unpacking the device. Xiaomi Vacuum Mop Essential is no exception. It seems that pouring water is a simple operation, but the design features of the model put many people in a stupor. Where exactly is the reservoir? How not to confuse the garbage compartments and liquid? Why does not water go to the rag?
The answer to these questions lies in the combination container. Unlike the top models with separate tanks, Mop Essential uses a single module that separates dry and wet collection. The correct installation and filling of this module is critical for quality wet cleaning. An error at this stage can lead to leakage or breakage of electronics.
This guide will take a closer look at how you prepare your device for work, and we'll look at every step from removing the container to choosing the right mode in the app, and following the instructions will extend the life of your gadget and keep the floors clean.
Design features of the combined tank
Before you start pouring liquid, you need to clearly understand the device of the container. Xiaomi Vacuum Mop Essential uses a 2-in-1 system. This means that the dust collector and water tank are combined into one housing, but separated by sealed partitions. The water compartment is located in one section, while the other is designed exclusively for collecting dust and fine debris.
The visually divided container is two unequal parts: the larger section with the HEPA filter and the mesh is the dry garbage area. The smaller section, often with the characteristic rubber seal lid, is designed for liquid. This is where you pour water. It's important not to confuse these areas, because getting water into the dust compartment will lead to the filter getting wet and potentially the engine failing.
The water tank lid is equipped with a special valve, which regulates the water supply to the napkin. When closed, the valve prevents fluid from leaking out when the robot moves or tilts. The design is designed to minimize risks, but the tightness depends on the correct installation of the lid.
⚠️ Warning: Never try to pour water through filters or a dust collector net, which will cause permanent damage to the electronics and loss of warranty.
The materials used in the tank are water resistant, but not for aggressive chemistry. The use of ordinary tap water is acceptable, but it is better to use filtered liquid to prolong the life of the nozzles and pumps, which will prevent scale from forming inside the thin channels of the supply system.
Step-by-step: how to remove and open the tank
The process of preparing for wet cleaning begins with removing the container from the vacuum cleaner body, which requires you to turn the device upside down. On the bottom panel, you will see the locks, the holding module. Press the tongue of the locker and smoothly pull the container over yourself. You should not make sudden movements so as not to damage the contact groups.
Once you remove the module, find a water tank lid, which is usually on top or side of the combined container, and is marked with the water drop symbol. Open the lid by pulling a special ledge, underneath which you will see a pouring hole, and that's where you need to pour water.
There are several nuances that should be considered when opening the tank:
- 💧 Make sure that the rubber seal on the lid is clean and fits tightly to the body, otherwise leaks are possible.
- 🚫 Do not open the lid while the container is inside the robot, even if it is off.
- 🧼 Before the first pouring, it is recommended to wash the tank with clean water to remove the production dust.
If the lid is difficult to open, don't put too much effort into it. Check if the debris is stuck in the lock mechanism. In some cases, you need to slightly turn the lid counterclockwise before lifting. Mechanical action should be moderate, plastic brittle at low temperatures.
☑️ Preparation for wet cleaning
Filling rules: what water to use and to what mark
The quality of the cleaning and the durability of the device depends on what you fill the tank. The manufacturer recommends using ordinary tap water, but with reservations. If the water in your area is very hard, it is better to filter it beforehand or use bottled water, which will save the supply system from clogging with mineral deposits.
It is strictly forbidden to add detergents, linen conditioners, chlorine-containing liquids or flavors to the tank. Aggressive chemistry destroys rubber seals, plastic tubes and pumps. Foaming substances can cause fluid level sensors to malfunction. Floor disinfection use special products designed specifically for robotic washing systems, and only at the recommended dosages, if the model allows.
The inside of the tank has liquid level tags, usually MIN and MAX, and you have to pour the water right up to the top of the tank, and if you overflow above the MAX, you can push the water out and into the dust bay or electronic contacts when you close the lid, and if you don't do it, you can reduce the battery life of wet cleaning.
| Type of liquid | Recommendation | Risks. |
|---|---|---|
| Tap water | Allowable (preferably filtered) | Scaling at high stiffness |
| Distilled water | Recommended | No risk to the system |
| Cleaning supplies | Forbidden. | Destruction of seals, foam, breakdown of the pump |
| Hot water (>40°C) | Forbidden. | Deformation of the plastic tank |
Water temperature also matters. Use a room temperature liquid. Hot water can deform a thin-walled plastic tank, which will lead to leakage. Cold tap water in winter is also undesirable, let it warm to room temperature before pouring.
Installation of the tank and start of wet cleaning mode
Once the water is filled, you need to securely close the tank lid. Make sure that there is a characteristic click indicating a fixation. Then set the combined container back into the vacuum cleaner body. It should stand tight, without gaps. If the container dangles, remove it and try to install it again, checking the guides.
The next step is to install a microfiber napkin, which is attached to a plastic platform (holder) on Velcros or special clamps, and it's important that the fabric is evenly spread and does not hang around the edges, otherwise the robot can get stuck, and the napkin platform is mounted on the bottom of the container, pressing against the water supply valve.
To activate the water supply, you need to turn on the appropriate mode.
- 📱 Using the Mi Home/Xiamo Home app: Select your device, go to the cleaning settings and select Wet Cleaning or Washing and Washing mode".
- 🔘 With the help of buttons on the body: depending on the modification, prolonged pressing or a combination of buttons can switch modes (confirmation is required in the manual of a particular version).
You can also adjust the water intensity in the app. There are usually three levels available: low, medium and high. To maintain cleanliness at a low level daily. If the floor is heavily polluted, choose medium or high mode. Electronic valve control allows you to save water and increase the cleaning area on one tank.
⚠️ Warning: Do not run a robot with wet cleaning mode on carpets or carpets. a napkin can get wet and stain the pile, and a robot can get stuck.