How to start wet cleaning on a Xiaomi robot vacuum cleaner: a complete guide with tips

Robot vacuum cleaners Xiaomi has long ceased to be just “smart brooms” – modern models such as Mi Robot Vacuum-Mop 2 Pro, DreameBot Z10 Pro or Viomi V3, They combine dry and wet cleaning to become full-fledged housekeepers, but many users face problems when they first start the wet cleaning function: the robot leaves the divorce, does not clean the floor properly, or ignores the command altogether. In this article, we will analyze the step-by-step configuration algorithm, the nuances of choosing wipes and detergents, as well as typical errors that spoil the result.

It's important to understand that wet cleaning works differently from traditional mops: there's no water pressure or rotating brushes. Instead, the robot evenly distributes moisture through a microfiber wipe pressed against the floor with a certain amount of force. The effectiveness depends on proper preparation, from choosing the mode in the Mi Home app to properly installing the water tank. If you've never used this feature or switched from another model (like Roborock), the instructions below will help avoid common mistakes.

Which Xiaomi models support wet cleaning?

Not all Xiaomi robot vacuum cleaners can wash floors, and the wet cleaning feature is available in the following series:

• 🔹 Mi Robot Vacuum-Mop – budget models with a basic water tank (for example, Mi Robot Vacuum-Mop 2 Lite).
• 🔹 Mi Robot Vacuum-Mop 2 Pro/Ultra — Advanced versions with electronic water control and lifting napkins on carpets.
• 🔹 DreameBot (series) D9, Z10 Pro, L10 Pro) – flagships with vibration napkin and adjustable pressure.
• 🔹 Viomi (e.g. Viomi) V3 or SE) — models with large tanks and support for hot water (in some versions).

To check if your model supports wet cleaning, go to the Mi Home app and open the Cleaning section. → Modes. If there are options like Wet Cleaning or Dry Cleaning. + Wet, so the function is available. Models without electronic water control (e.g. Mi Robot Vacuum) 1S) They may have a removable napkin container, but in fact they simply "smear" moisture without intensity control.

Preparing the robot for the first wet cleaning

All components must be properly installed before cleaning is started, and skipping at least one step can lead to leaks or poor quality washing.

Installation of a water tank

In most Xiaomi models, the water tank is located behind, under the lid, to install it:

1. Remove the dust collector (usually press the Release button and pull up).
2. Insert the water tank before clicking - it should sit tightly on the guides.
3. Pour the water to the maximum level (usually 200-300 ml). Use only distilled or boiled water to avoid plaque.

2. Fixing the napkin

Wet cleaning wipes come with a kit, but often you have to buy them separately.

• 🧼 The wipe should be made of microfiber with a pile of at least 300 g / m2 (thin wipes quickly tear).
• 🔄 Put it on the mount so that the Xiaomi logo is on top (this ensures the correct direction of the pile).
• 🔧 Fix the latches on the sides - the napkin should not hang, but you should not drag it over.

If you have a model with a napkin lift (for example, DreameBot) L10 Pro, make sure the feature is enabled in the settings, so that the robot automatically picks up a napkin on the carpets so that it doesn't wet them.

Setting up wet cleaning in the Mi Home app

Cleaning modes are managed through the official Mi Home app (or Dreame/Viomi Consider the process using the Mi Robot Vacuum-Mop example. 2 Pro:

1. Open the app and select your robot.
2. Go to Cleaning (or Cleaning in English).
3. Click on Cleaning Settings (Cleaning Settings).
4. In the section Cleaning mode, select one of the options: 💧 Only wet cleaning – the robot will only wash the floor, ignoring dust. 💨💧 Dry + wet cleaning - combined mode (first vacuum cleaner, then wash). 🔄 Zone cleaning – you can set wet cleaning only for certain rooms.

Intensity of water supply

Water Volume

• Low - for laminate or parquet.
• Medium - for tiles or linoleum.
• High for severe pollution (risk of divorce!).

For Dreame models (e.g. DreameBot) Z10 Pro) an optional option Vibration cleaning is available - the napkin vibrates at a frequency of up to 3000 rpm, which improves the cleaning of the tile joints.

💡

If your model has a hot water function (for example, in Viomi) V3), Use it only for severe contaminants, and washing it with hot water reduces the life of the wipe.

Table: Wet cleaning regimes and their application

If you use a detergent, add it to the water according to the instructions (usually 1-2 caps per 300 ml). Xiaomi recommends original liquids, but versatile tools for robot vacuum cleaners (for example, from the same source). Kärcher). Never use it:

• 🧴 Household detergents (such as Fairy) – they foam and can damage the pump.
• 🧂 Vinegar or citric acid - corroded by rubber seals.
• 🌿 Essential oils – leave a greasy film on the floor.

Common Mistakes and How to Avoid Them

Even when you set up the right thing, users often have problems, and here are the most common ones:

⚠️ Attention: If the robot leaves a strip of water, check the tightness of the tank. In Mi Robot Vacuum-Mop 2 Lite models, the valve often leaks due to wear of the sealing ring. MDY-007) reduce the level of water.

1. Post-cleaning divorces

Causes and solutions:

• 💦 Too much water – reduce the intensity in the settings or use a napkin with a denser pile.
• 🧽 Dirty wipe – wash it after each cleaning (manually, without bleach).
• 🧴 Inappropriate detergent – see the list of prohibited products above.

2.The robot doesn't wash the floor

Possible problems:

• 🔋 Battery discharge - wet cleaning requires more power. Charge the robot to 80%.
• 🚫 Blocked pump - check if the water supply hole is clogged (clean with a needle).
• 📱 Firmware failure – restart the robot (hold the Power button for 10 seconds).

3. The napkin moves or tears.

This is a problem for vibrating models.

• 🔧 Check the mountings of the napkin - they should be snapped to the end.
• 🧵 Use wipes with silicone inserts (such as from Roborock) that are better fixed.
• ⚙️ Reduce the vibration intensity (if you have such an option).

Care for the robot after wet cleaning

To prolong the life of your assistant, follow these rules:

1. Clean the tank: After each cleaning, drain the water and dry the container in air (do not use a hair dryer!) once a week, wash it with vinegar solution (1:1 with water) to remove the plaque.
2. Washing wipes: Wash by hand at a temperature not higher than 30°C. Do not use the underwear conditioner - it clogs the pores of the fabric.
3. Pump cleaning: In models with electronic water supply (for example, Mi Robot Vacuum-Mop 2 Pro), clean the pump once a month with compressed air (you can use a keyboard canister).
4. Storage: If you haven’t used the robot for more than a week, remove the napkin and water tank to avoid mold.

💡

Use distilled water – this reduces the formation of scale in the pump and prolongs the life of the robot by 20-30%.

For models with self-cleaning wipes (for example, DreameBot) L10 Pro) clean the base station brushes every 3 months from accumulated debris. Use a soft brush or vacuum cleaner at minimum power.

Xiaomi Comparison with Competitors: Which Is Better?

If you still choose a robot vacuum cleaner, compare Xiaomi with the main competitors in terms of wet cleaning quality:

Xiaomi loses Roborock in the pressure of the wipe on the floor, but wins in the cost of consumables. Dreame offers the best price/quality balance thanks to vibration technology. If you care about deep cleaning of tile seams, pay attention to DreameBot L10 Pro or Roborock S7 MaxV.

FAQ: Frequent questions about wet cleaning