Modern plumbing is becoming more intelligent, and automatic dispensers for soap from Xiaomi are in the lead in this segment. Users often face the question of how to fill the soap soap soap soap soap so as not to damage the sensitive foam mechanism and keep the case tight. Incorrect maintenance actions can lead to clogging pumps or leaks, so it is important to follow a proven algorithm of actions.
Unlike traditional bottles, Mijia series devices require the use of liquid soap of a certain consistency and careful handling of electronics. In this article, we will discuss the process of replenishing consumables, discuss the compatibility of various detergents and answer frequent questions from owners of smart gadgets for the bathroom.
Before you start replacing content, you need to prepare your workplace to prevent water from leaking to your electronic contacts. The safety of your device depends on the cleanliness of your hands and the dryness of the surface you're going to be manipulating. Let's look at the basic preparation steps and the refueling process.
Preparation for refueling and choice of means
The first step is to select the right detergent, because the viscosity of the liquid is critical to the operation of the peristaltic pump. Too thick soap can jam the mechanism, and too liquid can lead to uncontrolled dripping from the nose. The optimal solution is special interchangeable units from Xiaomi, which guarantee the perfect operation of the device.
If you plan to use third-party means, you need to pay attention to the absence of large abrasive particles and scrubbing elements in the composition. Such inclusions can irrevocably damage thin tubes and valves inside the housing. The liquid should be uniform, without stratification and sediment.
⚠️ Warning: Use of soaps with oil content above 5% or high concentrations of glycerol can lead to oxidation of internal seals and loss of leakage.
To be successful, it is also important to make sure that the battery is at least 20% charged. The energy consumption at the time of pumping a new portion of liquid is much higher than at a normal dosage, and the discharged battery may not cope with the task.
💡
Use warm (but not hot) water to rinse the tank before refueling – this will improve the dissolution of the residues of old soap and prevent the formation of traffic jams.
Step-by-step instructions for replacing the block
The process of replacing the cartridge or refilling the tank requires consistency and accuracy. First, remove the top cover of the device, which is usually fixed to the threaded connection or special latches. Rotate the top counterclockwise, applying a moderate force to avoid breaking the plastic thread.
Once the lid is removed, you will have access to the pump mechanism and the tank. If you are using the original Mijia replacement unit, just remove the empty bottle and install a new one, snugly inserting it into the seat until the characteristic click. The tube should be straightened and lowered to the bottom of the container.
☑️ Algorithm for cartridge replacement
If refilling a reusable tank, rinse the container with warm water to remove the residues of the old remedy. pour new soap, trying not to transfuse above the maximum mark if it is provided by the design, or leave a small air gap to create pressure.
The final step is to assemble the device, tightly wrap the lid, making sure that the sealing gum is right in its groove, and the tightness of the connection ensures that moisture does not get inside the case and will not cause the electronics to short.
System pumping and removal of air traffic jams
After installing a new cartridge or pouring liquid, air bubbles inevitably remain in the system, which prevent the dispenser from working properly. To eliminate this problem, you need to perform a primary pumping procedure. Most Xiaomi models have a special mode or require multiple pressing of the sensor to start the mechanism.
Press the touch button 3-5 times in a row at intervals of 2-3 seconds. You will hear the characteristic sound of the motor, and after a while the foam will begin to flow from the nose. If the foam does not go, perhaps an air traffic jam has formed in the tube, which must be "pushed through".
| Symptoms. | Possible cause | Method of decision |
|---|---|---|
| Engine hums, no foam. | Air traffic jam in the tube | Multiple touches of the sensor |
| The foam is too liquid | Low viscosity of the means | Replace soap with thicker soap |
| The device is not switched on. | Battery discharged | Charging via USB-C port |
| Weak jet pressure | Nosal contamination | Washing with warm water |
In some cases, you have to wait a few minutes after refueling to fill the supply channels completely, and the stability of the device during the first hours of operation may be lower than normal, but after full pumping of the system, everything will normalize.
The Secret to Perfect Foam
Features of maintenance of reusable tanks
Owners of reusable soap box versions should pay special attention to the hygiene of the inner surface. Over time, bacterial plaque or mold can form on the walls, especially if the device is in high humidity conditions. Regular disinfection will prolong the life of the device.
Use soft detergents without chlorine or aggressive solvents to clean. Chlorine-containing formulations can corrosion the metal elements of the pump and destroy the plastic. After washing, be sure to rinse the tank thoroughly and dry it before reassembling.
Pay attention to the condition of the fluid intake tube, if it becomes cloudy or covered with plaque from the inside, it must be replaced or thoroughly brushed, and a clogged tube is one of the most common reasons why automatic feed stops working.
⚠️ Warning: Never immerse the bottom of the electronics and motor device in water. You can only wipe the body with a slightly damp cloth.
Solving typical problems in operation
Even with the right filling, users can face a number of challenges, and often the problem lies not in the device itself, but in the characteristics of the poured product. If the soapbox stops foaming, try diluting the product with a little water or, conversely, replacing it with a more concentrated one.
Another common problem is that the sensor will spontaneously act, which can be caused by contamination of the infrared sensor or direct sunlight, and wipe the sensor area with a soft napkin and see if light is falling on it from a window or lamp.
If the device makes strange sounds or vibrates without foaming, it may have been a foreign object or crystals of dried soap, which may require a deeper disassembly and washing of the feed unit under a stream of warm water.
Device care and extension of service life
To make a smart soapbox last, you need to follow simple rules of operation: regularly wipe the case from water drops and soap spray to maintain an aesthetic appearance and prevent corrosion of contacts. The cleanliness of the external surfaces also affects the operation of the sensor.
Avoid emptying the tank completely during use. Dry pumping can cause it to overheat and wear prematurely. Try to install a new cartridge or fill up the liquid when the residue level is about 10-15%.
For prolonged non-use of the device (for example, when going on vacation), it is recommended to remove the cartridge or remove the batteries if the model is not lithium, this will prevent possible leaks due to changes in pressure inside the container and save battery power.
💡
Timely replacement of food items and the use of high-quality detergents increase the service life of the dispenser by 2-3 times.