Wet cleaning mode in Xiaomi Vacuum Mop P: how to turn on and configure

Xiaomi Vacuum Mop P combines dry and wet cleaning, but many users have difficulty first turning on the floorwashing mode. Unlike classic models, where you just need to attach a napkin, you need to adjust it properly through the Mi Home app and physically prepare the device. Without activating the appropriate mode, the robot will simply drive across the floor with a dry cloth without moisturizing it.

In this article, we’ll look at all the ways to enable wet cleaning, from basic in-app settings to manual control from the remote, and how to avoid common mistakes, such as why a robot might ignore a floor wash command (spoiler: often faulty is a water tank), or how to choose the optimal humidification intensity for different types of coatings. If you’ve just unpacked a Vacuum Mop P or haven’t used a wet cleaning feature in a long time, this guide will help you set things up from scratch.

Preparing the robot for wet cleaning: what to check before turning on

Before you activate the wash mode, make sure the robot is physically ready for the procedure. Without a properly installed water tank and cloth, the wet cleaning function will not work - the system will simply ignore the command from the application.

• 🔋 Battery charge: not lower than 20%. When low, the robot automatically turns off the wet cleaning to get back to base.
• 💧 Water tank: check that it is filled with distilled or filtered water (a regular tap water can leave divorces). MAX (typically 200-250 ml).
• 🧹 Cloth: It should be clean and properly attached to the holder, and if the cloth is torn or moved, the sensors will not recognize it, and the humidification will not turn on.
• 🚫 Obstacles: Remove long-pile carpets, wires and small objects from the floor. The robot can catch on and interrupt cleaning.

Pay special attention to the type of cloth. The Xiaomi Vacuum Mop P comes with a microfiber wipe, but over time its fibers wear out. If you notice that the floor remains moist for too long or, conversely, dries out quickly, it's time to replace the cloth. The original consumables can be found in the ZNMS01JM article.

⚠️ Warning: Never use detergents or bleach in a water tank. Chemicals can damage the pump and sensors of the robot, and leave a sticky plaque on the floor. For flavoring, it is allowed to add 1-2 drops of essential oil (for example, lavender), but not more than 1 time per week.

Method 1: Enabling wet cleaning through the Mi Home app

The main method of activation is through the official Mi Home app (or Xiaomi Home in newer versions). The interface may vary slightly depending on the region and version of the software, but the general logic is the same.

1. Open Mi Home and select your Xiaomi Vacuum Mop P robot vacuum cleaner from the list of devices.
2. On the main screen, tap the Clean button (or Clean in English).
3. At the bottom of the screen, you'll see a panel with settings (💧) — This is the wet cleaning mode.
4. Choose the intensity of hydration: 🌊 Weak (Low) - for laminate and parquet; 💦 Medium (Medium) - for tiles and linoleum; 🚿 Strong (High) - for persistent contaminants (use carefully!).

Press Start to start cleaning.

If the wet cleaning button is inactive (grey), check:

• 🔌 Connecting the robot to Wi-Fi (without the Internet, some functions are blocked).
• 🔄 Firmware Update: Go to Settings → Update the software and install the latest version.
• 🛠️ Sensor status: wipe the IR sensors on the bottom of the robot with a dry wipe (dust can block the signal).

Install water tank to the mark MAX

Secure the cloth on the holder

Select the intensity of moisture in the application

Check the Wi-Fi connection

Update the firmware of the robot (if available)-->

Method 2: Control from a physical remote control

If the application is not available (for example, there is no Internet), you can enable wet cleaning using the remote control that comes with it. This method is less flexible — you can not choose the intensity of humidification, but it works offline.

Instructions:

1. Make sure the robot is on and on standby (blue light).
2. On the remote, press and hold the Mop button (a rag image) for 3 seconds until you hear an audible signal.
3. Press the Start (triangle button) to start cleaning.

Note that when you're operating from the remote, the robot uses the default average humidity level, and if you want to change the intensity, you'll have to go back to the Mi Home app.

⚠️ Attention: Some users confuse the Mop button with the Turbo button, which increases the suction power but does not include wet cleaning. If you press the wrong button, the robot will start cleaning without water.

Setting up areas for wet cleaning: how to wash only the kitchen or bathroom

By default, the Xiaomi Vacuum Mop P cleans every room it passes through, but often only certain areas need to be moistened, such as kitchen tile, avoiding laminate in the living room, and the Mi Home app has a selective cleaning feature.

How to set up:

1. Open the room map in the application (Map or Map section).
2. Slip the Zone (or Zones) icon on the bottom menu.
3. Draw a rectangle around the area to be washed, such as encircling the kitchen floor.
4. In the window that appears, select: 🧽 Wet cleaning only (Mop only); 💨 Wet. + vacuum cleaner (Vacuum and mop); 🔄 Repeat 2 times (for severe pollution).

Specify the intensity of moisture and press Save.

Tip: If you have multiple floors, create separate maps for each, move the robot to a new floor, start cleaning and wait for it to build a new map, then assign a name to each map in the settings (e.g., "1 floor", "2 floor").

Once a day.

2-3 times a week

Only if necessary.

Rarely or never-->

Common mistakes and their solution

Even with the right setup, wet cleaning can not work properly, and the table below summarizes the typical problems and ways to fix them:

If the problem persists, try resetting the robot to the factory.

1. Turn the robot over and find the Reset button (usually next to the power button).
2. Press and hold it for 5 seconds until the indicator flashes.
3. Connect the robot to Mi Home again, as in the first run.

Tips for caring for a wet cleaning system

To extend the life of the robot and avoid breakdowns, follow these recommendations:

• 🧼 Clean the tank: after each cleaning, drain the water and rinse the container. Once a week, disinfect it with a solution of vinegar (1 tbsp. spoon per 1 liter of water).
• 🧺 Wash it by hand at 30.°C without bleach. Don't use machine washing - microfibre can deform.
• 🔧 Pump: once a month check it for blockages (see spoiler above). If the robot has become worse moisturize the floor, most likely the problem is in the pump.
• 📱 Updates: regularly check for new firmware versions. The manufacturer often fixes bugs in the wet cleaning operation.

For Xiaomi Vacuum Mop P, branded disposable wipes with antibacterial impregnation (ZNMS02JM article) are released. They are suitable for allergies and houses with animals, as they prevent the reproduction of bacteria in a cloth. The cost of packaging (10 pcs) is about 500-700 rubles.

💡

If the robot is often lost in the kitchen due to shiny surfaces (such as a refrigerator), stick matte tape on them.

Xiaomi Vacuum Mop P comparison with other wet cleaning models

The floorwashing function is implemented differently in Xiaomi’s line of robot vacuum cleaners, and the table below shows the key differences between the Vacuum Mop P and popular analogues:

Xiaomi Vacuum Mop P is the best choice for those looking for a balance between price and functionality. It is inferior to flagship models in terms of tank size and no automatic lifting of the cloth, but copes with daily cleaning as well. If you need a smarter wet cleaning (for example, with carpet sensors), look at the Vacuum Mop 2 Pro.

💡

For laminate and parquet, always choose the minimum level of humidification. Excess water can cause the coating to bloat, especially at joints.

FAQ: Answers to Frequent Questions