How to turn on Bluetooth on the Xiaomi vacuum cleaner: detailed instructions for all models

Xiaomi’s robot vacuum cleaners have long been an integral part of smart homes, but they cannot work properly without a stable connection to a smartphone. The main communication channel between devices is Bluetooth, which is used for initial setup, firmware updates and management through the Mi Home or Dreamehome app. However, many users face the problem: the vacuum cleaner is not visible in the list of available devices, and the Bluetooth indicator does not light up.

In this article, we will discuss how to properly turn on Bluetooth on a Xiaomi vacuum cleaner (including Mi Robot Vacuum-Mop 2C/2S/2 Pro, Dreame D9/F9/Z10 Pro, Viomi V2/V3 and others), which buttons are responsible for this, and what to do if the module refuses to activate. You will also learn how to reset communication settings if the vacuum cleaner “forgot” your phone, and what alternative ways to connect are available. Important: on some models (for example, Dreame W10), Bluetooth only automatically turns on low charge - this is not a fault, but a specialty of the firmware.

Which Xiaomi Vacuum Models Support Bluetooth?

Not all Xiaomi robot vacuum cleaners are equipped with Bluetooth module – some budget models (for example, Mi Robot Vacuum 1S) use only Wi-Fi for communication.

If your model is not in the table, check the specifications on the official Xiaomi website or in the instructions. For example, the Mi Robot Vacuum 1T series vacuum cleaners do not have Bluetooth - they only connect via 2.4 GHz Wi-Fi.

Where is the Bluetooth button on Xiaomi vacuum cleaner?

The location of the Bluetooth activation button depends on the model, and in most cases it is the combination key, which is also responsible for resetting Wi-Fi or enabling pairing mode.

• 🔘 Mi Robot Vacuum-Mop 2C/2S/2 Pro: button Wi-Fi/Bluetooth (antenna icon on the top panel. 3–5 seconds until the blue light flashes.
• 🔘 Dreame D9/F9/Z10 Pro: Reset button (hole with the inscription) RST) — require to be held up by a paper clip or toothpick 5 seconds.
• 🔘 Viomi V2/V3: Home button combination (Home) + On (Power) - Hold on 5 seconds before the beep.
• 🔘 Xiaomi Mi Robot Vacuum X10+: separate Bluetooth button under the cover (near the reset button).

Some models (like the DreameBot L10 Pro) don’t have a Bluetooth button — the module turns on automatically when you first start or reset. If you can’t find the button, check the instructions for your model or use the FAQ at the end of the article.

Step-by-step: how to turn on Bluetooth on the vacuum cleaner Xiaomi

The Bluetooth activation process consists of several steps: vacuum preparation, module activation and pairing with the smartphone. Follow the instructions below to avoid errors.

Step 1: Preparation of the vacuum cleaner

Before turning on Bluetooth, make sure that:

• 🔋 The vacuum cleaner is charged at least 20% (some models require 50 percent%).
• 📶 The vacuum cleaner is in the Wi-Fi coverage area (if you plan to connect to the Mi Home).
• 🔄 There is no active cleaning on the vacuum cleaner (click On/Off to stop it).

Step 2: Turning Bluetooth on

Follow the steps depending on the model:

Make sure the vacuum cleaner is turned off (indicators do not burn)

Find the Bluetooth button (see section above)

Hold the button for 3-5 seconds until the blue indicator or beep flashes

Release the button – the Bluetooth module is activated-->

If the indicator does not catch fire, try:

• 🔄 Reload the vacuum cleaner (hold on 10 seconds).
• 🔌 Connect to charging for 5 minutes, then try again.
• 📱 Make sure that the smartphone is enabled Bluetooth (in the settings or the quick access panel).

Step 3: Matching with a smartphone

After activating Bluetooth on the vacuum cleaner:

1. Open the Mi Home or Dreamehome app.
2. Click Add Device (+) → select the category "Vaccines".
3. Follow the instructions on the screen. The vacuum cleaner should appear in the list of available devices (the name will begin with MiRobot or Dreame).
4. Confirm the conjugation - a signal should sound on the vacuum cleaner.

💡

If the vacuum cleaner doesn’t appear on the list of devices, try turning off Wi-Fi on your smartphone – sometimes this helps avoid conflicts when you first connect.

What to do if Bluetooth is not turned on?

If the Bluetooth module is not activated after all the manipulations, the problem may be a hardware failure or a software error.

Reason 1: Battery discharged

Many models (e.g. Dreame D9) lock the Bluetooth module at a charge level below 15%. Connect the vacuum cleaner to the charging station for 30 to 60 minutes, then try again. If the charging indicator is not on, check:

• 🔌 Correction of the cable and power adapter.
• 🧹 Cleanliness of contacts on the vacuum cleaner and docking station (wipe with alcohol).
• 🔋 Battery status (if the vacuum cleaner discharges quickly, battery replacement may be required).

Reason 2: Firmware failure

If the vacuum cleaner was previously working with Bluetooth, but suddenly stopped turning on the module, the reason may be a damaged firmware.

1. Reset to factory settings: Hold the On + Home button for 10 seconds (for Viomi) or the Reset button for 5 seconds (for Dreame).
2. Update the firmware through the Mi Home application (Site “Device settings” → “Software update”).

Reason 3: Hardware malfunction

If none of these things worked, the Bluetooth module itself may have failed, and you can tell by the following:

• 🚨 The vacuum cleaner does not respond to any buttons (except mechanically switching on).
• 🔊 When holding the Bluetooth button, there is no sound signal or flashing of the indicator.
• 🔧 In the Mi Home app, the vacuum cleaner appears as “Offline” even after being reset.

In this case, contact the service center Xiaomi. the average cost of replacing the Bluetooth module is from 1,500 to 3,000 rubles (depending on the model).

💡

If the vacuum cleaner is new and on warranties, do not try to disassemble it yourself - this will void warranty obligations.

How to reset Bluetooth settings on Xiaomi vacuum cleaner?

If the vacuum cleaner has previously been connected to another phone or there are pairing errors, you may need to reset your Bluetooth settings, which will remove all stored devices from the vacuum cleaner's memory.

Method 1: Through buttons on the body

For most models:

1. Turn off the vacuum cleaner (hold on 3 seconds).
2. Hold the Bluetooth/Wi-Fi (or Reset) button for 10 seconds until the double signal is heard.
3. The indicator should flash red - this is a confirmation of the reset.

Method 2: Through the Mi Home app

If the vacuum cleaner is connected to Wi-Fi:

1. Open Mi Home → Choose your vacuum cleaner.
2. Go to Settings → Additional → Reset Bluetooth.
3. Confirm the action - the vacuum cleaner will restart.

⚠️ Attention: after resetting Bluetooth vacuum cleaner may lose connection with Wi-Fi.

Alternative ways to connect a vacuum cleaner Xiaomi without Bluetooth

If the Bluetooth module is out of order or you can’t activate it, there are several alternative ways to control the vacuum cleaner:

• 📶 Wi-Fi connection: most models support LAN management, and this requires connecting the vacuum cleaner to the router (2.4 GHz network only!).
• 🎮 Remote: Some models (for example, Dreame) Z10 Pro) equipped with an IR panel for basic control.
• 🖥️ Control via voice assistants: if the vacuum cleaner is connected to Alice, Google Assistant or Siri, you can give commands without a direct connection.
• 🔧 Manual mode: buttons on the case allow you to start cleaning, return the vacuum cleaner to the base and enable spot cleaning.

If you need to update your firmware without Bluetooth, use the microSD instruction (see spoiler above).

Frequent errors in Bluetooth connection and their solutions

Even after successful Bluetooth activation, users often encounter pairing errors, and let's look at the most common problems and ways to fix them.

⚠️ Warning: If you use an iPhone, turn off the Interrupt feature in Bluetooth settings before connecting.

FAQ: Answers to Frequent Questions