How to make a solution for the dispenser Xiaomi: recipes and recommendations

Xiaomi smart cleaning dispensers are not just a handy accessory, but a key element that affects cleaning efficiency and durability. Incorrectly prepared solution can lead to clogging, plaque formation or even breakdown. In this article, we will discuss how to make a dispenser solution for Xiaomi, taking into account the features of various models, from Mi Robot Vacuum vacuum cleaners to Xiaomi Mop washing mops.

It's important to understand that the manufacturer recommends the use of original products, but the cost often forces users to look for alternatives. We tested several recipes and found the optimal proportions that will not harm the technique, you will also learn which ingredients are categorically not to mix, how to avoid common mistakes and what to do if the dispenser is already clogged.

Why do you need a special solution for Xiaomi dispenser?

The dispensers in Xiaomi’s smart appliances are designed to work with liquids of a certain viscosity and chemical composition. Using inappropriate detergents can lead to:

• 🔧 Dispenser clog – salt crystallization or too thick liquid blocks small holes.
• ⚡ Pump breakdown – aggressive components (e.g. chlorine) are corroded by rubber seals.
• 🧹 Poor cleaning quality – improper concentration of the product leaves divorces or does not remove dirt.
• 🚨 Warranty loss – the use of uncertified liquids may cause denial of service.

Xiaomi’s original solutions (such as Mi Home Moisturizing Detergent) contain a balanced composition of surfactants, water softeners and antibacterial additives. Their pH balance is neutral (6.5-7.5), which is safe for plastic and rubber parts. However, with a competent approach, you can make an analog at home.

What ingredients can be used for a homemade solution?

The following components are suitable for the preparation of a safe solution:

Prohibited ingredients:

• 🧪 Chlorine-containing bleach - destroy rubber seals.
• 🧴 Shower gels or shampoos – contain silicones that clog the dispenser.
• 🍋 Citric acid in powder – crystallizes and blocks sprayers.
• 🧽 Means for washing dishes with abrasives - scratch internal surfaces.

💡

Before first using a homemade solution, check it on a small area of the floor – some components (such as essential oils) can leave stains on the laminate or parquet.

Step-by-step instructions: how to prepare a solution for the dispenser

We recommend two proven recipes – universal (for all types of dispensers) and enhanced (for severe contaminants).

Recipe 1: Universal solution (for regular cleaning)

Suitable for Xiaomi Mi Robot Vacuum-Mop 2, DreameBot and Xiaomi Mijia washing mop.

Distilled water - 500 ml|Liquid soap (without dyes) - 15 ml|Vinegar 5% - 5 ml|Lemon essential oil - 2 drops-->

1. Heat the water to 40-50°C – This will accelerate the dissolution of components.
2. Add liquid soap and mix thoroughly until a uniform consistency.
3. Pour the vinegar and the oil, mix again. Don't use metalware - vinegar can react!
4. Let the solution settle for 10-15 minutes, then strain through gauze (to remove possible flakes).
5. Pour into the dispenser through the funnel, avoiding air.

Recipe 2: Reinforced solution (for fat removal and lime plaque)

Recommended for kitchen robot vacuum cleaners or equipment used in regions with hard water.

Composition:


- Distilled water - 400 ml




- Soda ash - 3 g (½ ppm.)




Liquid household soap - 20 ml




- Vinegar 5% - 10 ml

This solution can not be used more than 1 time per month - a high concentration of soda can damage rubber parts with prolonged contact.

How to pour the solution into the Xiaomi dispenser?

Even a perfectly prepared solution can harm the machinery if you pour it incorrectly.

1. Disconnect the device from the network (if it is a stationary appliance) or remove the battery (for robot vacuum cleaners).
2. Remove the water tank and wash it with warm water (no detergents!).
3. Use only the original funnel (comes with it) – it prevents the spilling and ingress of air.
4. Pour the solution slowly, at an angle of 45°, avoid bubble formation.
5. After pouring, close the dispenser cover and check the tightness - turn the tank down for 10 seconds.

For models with automatic dosing (for example, Xiaomi Mi Mop 2 Pro) it is important to:

• 📏 Do not exceed the maximum level - there is a mark on the tank MAX.
• 🔄 Washing the dispenser after every 5th use will prevent bacteria from forming.
• 🚫 Do not mix the residues of old and new solution – this can cause a chemical reaction.

💡

If your robot vacuum cleaner has started leaving wet marks or is not spraying water properly, this is the first sign of a clogging dispenser. Immediately flush the system as instructed by the manufacturer (usually the "Tube Cleanup" mode in the Mi Home app).

Frequent Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes when working with dispensers, and here are the most common ones and ways to prevent them:

⚠️ Attention! Never use boiling water to flush the dispenser, it deforms plastic parts. Maximum water temperature: 60°C.

Another common problem is that you forget to wash the dispenser after cleaning, and the residue of the detergent dries out, forming a film that hardens over time, to avoid this:

1. After each cleaning, drain the remaining solution.
2. Rinse the tank with warm water.
3. 1 time a week, start the cleaning cycle with clean water (without detergent).

How to clean the dispenser if it is already clogged?

If you notice that the robot vacuum cleaner is not good at spraying water or the mop leaves dirty stripes, chances are the dispenser is clogged.

Method 1: Mechanical cleaning (for weak blockages)

1. Remove the tank and disassemble it according to the instructions (usually you need to press the latches on the sides).
2. Wash all the parts under running water using a soft toothbrush to clean the sprayers.
3. To remove plaque, soak the parts in a solution of vinegar (1: 1 with water) for 30 minutes.
4. Dry all elements thoroughly before assembly (you can use a dryer in cold air mode).

Method 2: Chemical cleaning (for severe blockages)

If mechanical cleaning has not helped, use a special cleaner for coffee machines (for example, De'Longhi EcoDecalk) or prepare the solution:

Composition:


- Citric acid - 20 g




- Water - 200 ml




Solution temperature: 50-60°C




Soaking time: 1 hour

⚠️ After chemical cleaning, be sure to rinse the dispenser with clean water at least 3 times.Citric acid residues can damage rubber seals the next time you use them.

For models with a non-disassemblable dispenser (for example, Xiaomi Mi Mop P), use the self-cleaning function in the Mi Home app:

1. Put clean water in the tank.
2. In the application, select Cleaning Tube mode.
3. Repeat the procedure 2-3 times.

Alternatives: What can be used instead of a homemade solution?

If you don’t want to mess around with making the solution, there are a few proven alternatives:

• 🧼 Xiaomi’s original tools, such as Mi Home Moisturizing Detergent DJT01ZHM). Suitable for all models, but expensive.
• 🌿 Eco-friendly detergents - Ecover, Frosch (dilute 1:10 with water).
• 🧴 Glasses: Mr. Proper or Cif (no ammonia!) Dilute 1:5.
• 💧 Special liquids for robot vacuum cleaners - Dreame Floor Cleaner or Roborock Detergent.

When choosing an alternative, pay attention to:

• 📋 Composition - there should be no chlorine, abrasives, perfumes.
• 💧 Viscosity – the liquid should be fluid, without gel particles.
• 🔍 pH balance – optimally 6.0-8.0.

Important: Before using the alternative tool for the first time, check its compatibility with your model on the Xiaomi support site.

FAQ: Answers to Frequent Questions