Xiaomi’s modern wireless vacuum cleaners, such as the popular Mijia or Dreame series, have become an integral part of many apartments’ cleaning, with the main advantage of being mobile and without wires, allowing quick tidying of any room, but owners often wonder where to store the device between uses so that it does not occupy space on the floor and is always ready to go.
The best solution to save space is wall-mounted charging station, which not only frees up square meters, but also provides safety, eliminating the risk of tripping on the cord or hitting the device standing in the aisle. Properly fixed base allows the device to be stably charged and always at hand.
In this article, we will discuss the installation process, the necessary tools and the nuances of location selection, you will learn how to avoid typical drilling errors and how to securely lock the holder so that the equipment lasts for many years without the risk of falling.
Choosing the Right Place for Installation
The first and most important step is to determine the location for the installation. The ideal place should be as close to the electric outlet as possible, since the length of the charger cable in Xiaomi models is usually limited to one and a half to two meters.
The wall should be flat and made of a durable material that can withstand the weight of the vacuum cleaner with a fixed holder. plasterboard partitions without internal reinforcement or decorative panels made of thin plastic are not suitable for hanging heavy electrical appliances.
The lower edge of the base should be at a level that is convenient for removing and installing the vacuum cleaner, usually 90-110 cm from the floor. If you hang the base too high, it will be difficult for children or people of short stature to use it, and too low a setup can lead to accidental kicking.
⚠️ Warning: Never place a charging station in close proximity to heat sources such as heating batteries, or in areas with high humidity, such as inside a shower cabin or above a sink.
Check if the installed vacuum cleaner will interfere with the opening of cabinet doors or the passage of people in the corridor. The device in suspension has certain dimensions, and the protruding tube or handle should not become an obstacle in a narrow space.
Required tools and equipment
Before you start the action, you need to prepare the entire arsenal of tools. the standard box with vacuum cleaners Xiaomi often already contains a basic set for installation, but it can be minned. you will definitely need a punch or a powerful drill with impact function, especially if the walls in your house are concrete or brick.
Marking and quality control will require a building layer, a roulette and a pencil. Without the level, you can’t achieve a horizontal base position, which is critical for the correct contact of charging contacts, and prepare a hammer, a screwdriver (usually a cross), and possibly a vacuum cleaner to remove dust after drilling.
- 🔨 Perforator or impact drill with a drill on concrete with a diameter of 6 mm.
- 📏 Building level and roulette for accurate markup.
- ✏️ Pencil or marker.
- 🔌 screwdriver.
- 🧹 Vacuum cleaner or brush to clean crumb holes.
The holder usually comes with two dowels and two screws, however, if you plan to hang a heavy model, such as the Xiaomi Mi Vacuum Cleaner G10 or Dreame V11 with a full dust container, a regular fastener may not be enough, in which case it is better to purchase longer and stronger anchor bolts.
Hole marking and drilling process
Marking is a step where you can't rush, and you can apply a plastic mounting panel (the base of the holder) to the wall at the height you want to use, and you can use the level to get a strictly horizontal position, and you can use your pencil to mark the centers of future holes through special holes in the plastic.
Remove the panel and check the distance between the tags. It should correspond to the distance between the mounting holes on the panel itself. If you use regular dowels, the diameter of the drill should match the diameter of the dowel, usually 6 mm. The drilling depth should be 5-10 mm more than the length of the dowel, so that the dust does not interfere with the complete immersion of the fastener.
☑️ Checklist before drilling
When drilling, keep the tool perpendicular to the wall so that the hole is flat and the dowel sits tight. Once the drill is complete, be sure to blow the holes or use a vacuum cleaner to remove the concrete dust. If you don't, the dowel may not enter the end or hold tight enough.
⚠️ Warning: Before drilling, make sure that no electrical wires or pipes are laid at the installation site. Use a hidden wiring detector to avoid short circuits or water breaking through.
If the wall is lined with ceramic tiles, you need to drill extremely carefully. First, a special feather drill for ceramics at low revs is used to avoid splitting the tiles, and only then, after passing the glaze, you can switch to the impact mode to drill the main material of the wall.
Installation of the holder and reliability check
After the holes are ready, put the plastic dowels in them to the point, they should sit tight and not turn around. Then apply the mounting panel to the wall, combining the holes, and screw the screws. Don't twist them all the way to the end at once; first fix the panel, check the horizon level again, and only then tighten the fastener completely.
The anchored base is fitted with a decorative holder case (if your model design provides it), make sure all latches fall into place and nothing will swell. You can now install the Xiaomi vacuum cleaner on the base for inspection.
Try removing and placing the device several times, the fixing mechanism should work clearly, without distortion, if the vacuum cleaner is hanging curved or the contacts do not match, perhaps the base is installed with a slope, and the procedure will have to be repeated.
💡
To screws rotate more easily and the plastic of the dowels is not deformed, you can slightly lubricate the screw carving with household soap or paraffin before screwing.
Pay special attention to the contact group. There are metal charging plates on the base and handle of the vacuum cleaner. When you install the device, they should fit tightly together. If the contact is bad, the charging indicator may not catch fire and the device will remain discharged.
Comparison of Xiaomi Holder Models
Xiaomi’s various vacuum cleaners and Dreame’s sub-brand can come with different types of wall mounts, some of which allow you to store not only the vacuum cleaner itself, but also additional nozzles, making the storage system more functional.
| Model vacuum cleaner | Type of attachment | Storage of nozzles | Difficulty of installation |
|---|---|---|---|
| Xiaomi Mi Vacuum Cleaner 1C | Simple base. | No. | Low. |
| Dreame V11 / V12 | The base with the organizer | Yes (up to 3 pcs) | Medium |
| Xiaomi G10 | Universal holder | Yeah (on the hull) | Low. |
| Roborock H7 | Magnetic base | Yes (included) | Tall. |
As you can see from the table, more advanced models offer integrated accessory storage solutions, which eliminates the need to buy separate hooks or brush shelves, but these designs require more precise installation and more space around.
Can you use a holder from one model to another?
Alternative Storage and Care Methods
If you don't want to drill walls or you can't drill walls, there are alternatives. Some users use powerful vacuum suction cups with hooks, but for heavy power tools, this is a risky method. A more reliable option is to use ready-made floor racks that mimic wall mounts, but just stand on the floor.
Check the condition of the fastener regularly. Every six months, it is recommended to tighten the screws, as they can weaken from vibration (when removing the vacuum cleaner), also wipe the contacts on the base and vacuum cleaner with dry dust cloth, which can accumulate and worsen the quality of charging.
These simple rules will allow you to enjoy cleanliness in the house and order in the storage of equipment. Properly installed holder prolongs the life of the battery, providing constant contact with the network, and protects the nerves of the household, freeing up space.
⚠️ Warning: Do not attempt to modify the design of the holder or use homemade fasteners that do not fit the weight category of the device.
💡
The main key to success is the quality of surface preparation and the use of reliable fasteners that correspond to the material of your walls.