Xiaomi’s robot vacuum cleaners are well-deservedly considered one of the most reliable cleaning assistants, but even the most advanced equipment requires regular maintenance. Many owners wonder whether it is possible to wash the device whole, or limit yourself to cleaning the case, since moisture entering the house is fraught with the failure of expensive electronics. In this article, we will discuss the process of complete cleaning, paying attention to those nodes that can and should be washed with water.
Before you start water treatments, you need to clearly understand the design of your device, whether it is the Mi Robot Vacuum-Mop model or the more advanced version of the Mi Robot Vacuum-Mop 2 Pro.+. The main mistake of users is to try to wash the container for dust together with the installed HEPA-The moisture destroys the filter structure, turning it into a useless piece of fabric that stops trapping fine dust and can become a source of unpleasant odor.
The cleaning process should begin with completely disconnecting the device from the charging station and removing the dust collector, only after that you can start disassembling the removable elements, the correct preparation ensures that your gadget will last for many years without reducing the suction power.
Disassembly and preparation of components for washing
The first step in deep cleaning is to properly disassemble the main components that require contact with water, and you need to remove the dust collector, disconnect the filter from it, and remove the main brush from the bottom of the case. Wet cleaning models also remove the water tank platform and the napkin itself, all of which accumulate not only dust, but also fatty plaque, which over time begins to emit a smell.
Plastic garbage containers can be washed under running water using a soft sponge. If there is a dense layer of dust or wool stuck in the corners, a small amount of neutral detergent is allowed. However, avoid aggressive chemicals that can damage the plastic or cause an allergic reaction during subsequent use.
Special attention should be paid to the main brush, which often winds the hair and fur of animals, it must be removed by pulling special tongues, and cleaned of windings. After mechanical cleaning, the brush can be washed with warm water and soap, removing sticky dirt. Before installing it back, make sure that the bearings on the ends of the brush are free of pile and moisture, otherwise the mechanism may begin to emit extraneous noise.
- 🧹 Remove the side brush by pulling it upwards, and rinse with water, removing dust from the movable mechanism.
- 🗑️ Wash the plastic garbage container, making sure there is no old dirt left in the corners.
- 🌪️ Clean the main brush of wound hair and rinse it with warm water with a soft detergent.
- 💧 Remove the platform for the water tank and wipe it with a wet cloth, removing lime plaque.
Once all removable parts are disassembled, inspect them for damage. Cracks on plastic or stubble deformation may indicate the need to replace consumables. Regular visual inspection helps to detect small parts that may have gotten inside and damaged the mechanism.
Filter care: what can be washed and what can not be washed
The filtration system is the heart of any vacuum cleaner, and this is where users often make critical mistakes. Xiaomi devices typically use a two-stage system: a primary mesh filter and a finishing line. HEPA-Understanding the difference between the two is critical to maintaining cleaning efficiency and household health.
The primary filter, which is a small mesh, can and should be washed. It traps large dust, wool and hair, protecting the more sensitive elements. Rinse it under a stream of water until the draining liquid becomes clear. After washing, be sure to shake off the excess water and leave to dry in the straightened form for at least 24 hours.
⚠️ Attention: HEPA-filters (usually white or pink, corrugated) are strictly forbidden to wet! Water destroys microfibers, and the filter stops trapping allergens and fine dust. If it is contaminated, it must be replaced with a new one.
If you notice that even the dry HEPA-The filter leaks dust or the device smells bad, which is a sure sign that the material is exhausted, and trying to wash or blow it with compressed air will only temporarily improve the situation, but the structure of the fiber is already broken. Replacing filters is not a whim, but a necessity to maintain the declared suction power.
In some models, such as the Roborock S5 Max or Mi Robot Vacuum-Mop Essential, the design of the filter may differ slightly, but the principle remains the same: corrugated material is not friendly with water. Always check the marking on the filter frame before washing. If there is no icon of a water drop or tap, there is no risk.
How often do you change filters?
On average, HEPA-filter 6-12 The primary mesh filter, when properly maintained, can last for years, requiring only regular flushing.> Navigation of a robot vacuum cleaner depends on the purity of its sensors. The laser rangefinder (LiDAR) located in the upper tower, and the elevation difference sensors (cliff sensors) in the lower part of the housing must be absolutely clean. Dust that settles on the lenses can cause the robot to go blind, crash into furniture, or fall down stairs. Use a dry, soft microfiber to clean the sensors. If you see greasy spots on the lens, you can slightly moisten the fabric with water, but in no case do not spray the liquid directly on the sensor. Pay special attention to the wheels, which often overgrown with pile and hair, which reduces the permeability of the device. The wheels can be wiped with a wet wipe, removing the sticky dirt. If there is a dense lump of wool between the wheel and the body, carefully remove it with tweezers or toothpicks. Do not use sharp metal objects so as not to scratch the axle or rubber surface of the wheel. Clean wheels ensure uniform movement and proper construction of the room map. Frequency Cleaning Method Can be wet Laser Sensor (LiDAR) Dry Microfiber Once every 2 weeks No (only slightly wet fabric) Wheels Wet wipe, Toothpick Once a month No (wipe) Charging contacts Dry fabric, eraser When charging problems No Difficulty Sensors Difficulty Hand or fabric Once a month No Regular check of the lower panel of the device allows you to detect foreign objects that can jam the mechanism. Often small toy toy, coins or paper clips are removed. Removing such items prevents from breaking down the water system for the purpose of sizing the moisturing the system, so that the sing of the moisturing of the water sage and the system requires the sing of the sulating sing of the system for the sulating sulating sage. After each cleaning, it is recommended to drain the remaining water and wipe the tank from the inside with dry cloth. This will prevent the appearance of a musty smell that can spread throughout the apartment. If you notice that the water has stopped flowing uniformly to the napkin, the outlet or pump may have clogged. In this case, the tank can be gently washed with warm water. Do not use boiling water, since high temperatures can deform plastic walls or damage seals. To disinfect, you can use a weak solution of vinegar, but after that the tank needs to very carefully rinse the water formation of the electronically controlled water in the current water. Hard tap water can lead to clogs that are difficult to remove without disassembling the device. Wet cleaning wipes also need to be washed after each use. Machine washing at 40 degrees without using air conditioning for underwear is the best option. Air conditioning can reduce the absorbency of the fabric, which will negatively affect the quality of floor washing. Drying and assembly of the device is also necessary after cleaning. In no case do not assemble the device if at least one part is wet. Water that gets into the electronics compartment or contacts, even after a drying process, even after a short time, you start the process of cleaning. Avoid direct sunlight and open heat sources such as heating batteries or hair dryers. High temperatures can warp the thin plastic of containers and spoil rubber seals. Natural drying at room temperature takes 12 to 24 hours. Before final assembly, make sure that all grooves and joints are completely dry. Pay special attention to the charging contacts on the bottom of the vacuum cleaner and on the base - they should be dry and clean. If the contacts show oxidized plaque, gently wipe them with a dry cloth or eraser. 💡To make it easier to dry hard-to-reach areas, you can use a compressed air can, gently blowing moisture out of the cracks and joints. After you're fully assembled, start the device and let it work for a couple of minutes in idle mode. This will help to make sure that all the mechanisms work correctly, and there are no extraneous sounds. If the robot is behaving strangely, immediately turn it off and check that all components are installed correctly.Frequent errors when cleaning the robot vacuum cleaner Despite the apparent simplicity of the design, users often make mistakes that shorten the life of the device. One of the most common is to try to wash the entire dust collector with the filter, which, as mentioned, is detrimental to the system. HEPA-The second common mistake is to use aggressive solvents to remove stains from plastic, acetone, alcohol or chlorine-containing agents can make plastic brittle and cause microcracks, and over time, such a case can burst even from a slight impact. Also, chemical vapors can damage the plastic lenses of the sensors, making them cloudy.Use only water or soft dish detergents. ⚠️ Warning: Never immerse the main body of the robot in water, even if it seems to be sealed. Inside are speakers, microphones and control boards that do not have protection against full immersion. Another mistake is ignoring the side brush. Many people forget that it also needs to be cleaned and changed periodically. A worn brush with broken bristles makes it worse to rake up garbage to the main suction hole, which reduces the overall efficiency of cleaning around the perimeter of the room. 💡Compliance with the rules of drying and rejection of aggressive chemistry is the key to the long service of your robot vacuum cleaner Xiaomi. FAQ: Frequently asked questions: Can you wash a Xiaomi robot vacuum cleaner entirely under the tap? Absolutely not. You can only wash removable plastic parts: a garbage container (without a filter), a main and side brush, a water tank platform. The case itself with electronics, motors and batteries can not be washed. How often should you wash the dust container? It is recommended to rinse the container every 1-2 weeks, depending on the degree of contamination. If you clean every day and there are animals in the house, you may need to wash more often to avoid the appearance of odor. What if water gets into the vacuum cleaner? Immediately turn off the device, remove the battery (if the model allows) and the dust collector. Put the robot in a dry warm place (but not on the battery) for at least 48 hours. Do not try to turn it on for inspection until you are sure that the internal components are completely dry. Can you use a steam generator for the electrically decompressing the components? The best way to use a dry, soft microfiber fabric is to use the same type of fabric used to wipe glasses or smartphone screens, and if the contamination is severe, you can moisten the fabric slightly with water, but then be sure to wipe it dry.