Connecting Xiaomi Humidifier to Alice: Full Instruction with Solutions to Typical Problems

Voice control of the air humidifier from Xiaomi via Alice is not only convenient, but also practical: it takes one command to turn the device on, change the mode of operation or check the humidity level. However, many users face difficulties in the first setup: the device does not appear in the Yandex Smart Home, Alice does not see it, then synchronization errors occur. In this article, we will analyze all the stages of connection – from preparing devices to solving common problems – taking into account current updates in 2026.

It is important to understand that the process depends on the model of the humidifier. For example, for Xiaomi Mi Air Humidifier Pro and Smartmi Air Humidifier 2, the algorithm will be identical, but with budget models like Xiaomi, the algorithm will be identical. CJXJSQ02ZM There may be nuances, and we'll look at a generic method that works for most devices, and we'll also look at specific features for specific product lines.

If you’ve already tried to connect a humidifier to Alice and you’ve encountered an error, don’t rush to reset your settings. 90% of the time, the problem is solved by adjusting the settings in Mi Home or re-authenticating in Yandex Smart Home. And for those just starting out, we’ve prepared a step-by-step instruction with illustrations (see sections below) and a checklist to check each step.

1. Device Preparation: What to Do Before Connecting

Before you start syncing, make sure all the components are ready to go, which will save time and eliminate the need to redo the settings.

Requirements for the moisturizer:

• 🔋 The device must be charged (for models with a battery) or connected to the network.
• 📶 The humidifier should support Wi-Fi connection (check the model specifications).
• 🔄 Update your device to the latest version through the Mi Home app.

Requirements for smartphones and accounts:

• 📱 Install the latest versions of apps: Mi Home (for Android or iOS) Yandex (with support for Smart Home)
• 🔐 Sign in to both apps under the same account (preferably use it) @mi.com or @yandex.ru).
• 🌐 Connect your smartphone and humidifier to a single Wi-Fi network (2.4 GHz, as 5 GHz many Xiaomi devices do not support).

⚠️ Warning: If your humidifier has previously been connected to another Mi Home account, reset to factory settings. To do this, hold the power button for 5-10 seconds until the indicator starts flashing orange.

For Smartmi Air Humidifier models 2S And later, you'll also need to enable the "Allow Third-Party Services Management" option in the device settings in Mi Home, which came after the firmware update in 2023 and can be disabled by default.

2. Connecting the humidifier to the Mi Home app

This phase is the basis for further integration with Alice, and unless the device is added to the Mi Home, synchronization with the voice assistant will not be possible.

Instructions for addition:

1. Open the Mi Home app and go to Devices section» → «Add the device».
2. Select the Humidifiers category and find your model in the list. If you don't have one, use the "Add Manual" option.
3. Follow the hints on the screen: turn on the humidifier, holding the power button until the indicator blinks.
4. Connect your device to Wi-Fi by entering a 2.4 GHz network password.
5. Wait for the setup to be completed (it can take up to 2-3 minutes).

If the humidifier is not connected, check:

• 🔌 Correctness of the entered Wi-Fi password (registrar matters!).
• 📡 Distance to the router - the device should be no further than 5-7 meters.
• 🔄 Absence of special symbols in the network name (e.g, #, $, gaps).

The humidifier is on and flashes blue/orange|

Smartphone connected to Wi-Fi 2.4 GHz |

There is no Cyrillic alphabet or special symbols in the name of the network|

Mi Home app updated to latest version-->

⚠️ Note: Xiaomi Mi Air Humidifier models (CJXJSQ) You may need to manually specify the region of China in the Mi Home settings (even if you are in Russia) over 2021.

After successful addition, the device will appear in the main menu Mi Home. we recommend you to immediately update the firmware if an update is available, this will fix possible synchronization bugs.

3. synchronization of Mi Home with Yandex Smart Home

Now you need to “link” Xiaomi account with the service Yandex Smart Home, which will allow Alice to access devices through the cloud Mi Home.

Step-by-step:

1. Open the Yandex app and go to the Smart Home section (the house icon in the bottom menu).
2. Click "Add device» → «Other devices» → «Xiaomi».
3. Enter the username and password from the Mi Home account (the same one that the humidifier is connected to).
4. Allow access to devices by clicking “Confirm” in the authorization window.
5. Wait until the synchronization is complete (it can take up to 5 minutes).

What if the device does not appear in Yandex Smart Home?

• 🔄 Reset the humidifier (turn off/turn off from the socket).
• 📱 Delete and re-add Xiaomi account in Yandex Smart Home.
• 🌐 Check that the humidifier is tied to the correct region (e.g., “Russia” or “China” if the model is old).

For Smartmi Air Humidifier models 2S And later, you may also need to enable the "Yandex Smart Home" option in your device settings in Mi Home, which appeared in firmware from 2023-2026 and is disabled by default.

4.Setting up voice control via Alice

After successful synchronization, it remains to configure voice commands. Alice supports basic humidifier management functions, but additional adjustments may be required for advanced features (for example, setting an accurate humidity level).

List of supported teams:

• 🔊 «Alice, turn on the humidifier" - start the device.
• 🔊 «Alice, turn off the humidifier in the bedroom" - disconnect (if indicated location).
• 🔊 «Alice, set humidity 60%" - change target level.
• 🔊 «Alice, what is the humidity level in the room? – query of current data.

How to add a humidifier to a room for precise control:

1. Open Yandex Smart Home and find your humidifier in the list of devices.
2. Click on the device and select “Settings» → «Room».
3. Specify the location (for example, “Bedroom” or “Children’s”).
4. Save the changes.

For Smartmi Air Humidifier models 2S Mi Air Humidifier Pro is also available for extended commands:

• 🔊 «Alice, turn on the night mode on the moisturiser».
• 🔊 «Alice, set the minimum fan speed».

⚠️ Note: If Alice answers "Device is not responding", check: Connect the humidifier to the Internet (Wi-Fi indicator should burn blue). No restrictions on the router (for example, parental control or locking the device on the Internet). MAC-address).

💡

To make Alice recognize commands faster, add a humidifier to the Favorites in Yandex Smart Home. To do this, click on the star next to the device name.

5. Solving typical problems and errors

Even when you set it up properly, you can have failures, and we've collected some of the most common errors and ways to fix them.

1.The device is plugged in, but Alice can't see it.

• 🔄 Reset the humidifier (pull out the plug for 30 seconds).
• 📱 Delete and re-add Xiaomi account in Yandex Smart Home.
• 🌐 Check that the humidifier is tied to the correct region (e.g. China for older models).

2. Commands are executed with delay or not executed

• 📶 Check the quality of the Wi-Fi signal (use applications like Wi-Fi Analyzer).
• 🔌 Reboot the router.
• 🔄 Update the moisturizer firmware through Mi Home.

3. "Device not available" error

• 🔌 Make sure the humidifier is plugged in and the power indicator is on it.
• 📡 Check that the device is connected to a 2.4 GHz network (many Xiaomi models don’t work with 5 GHz).
• 🔐 Reauthorize in Mi Home and Yandex Smart Home.

4.Alice says "This feature is not supported" This means your humidifier model is not compatible with extended commands.Check the list of supported features in the device documentation or update the firmware.

💡

If the humidifier stopped responding to Alice's commands after the firmware update, try rolling back the software version via Mi Home (if available) or wait for a new patch from Xiaomi.

6. Additional settings for experienced users

If you want to get the most out of the humidifier, you can configure automation and integration with other devices in the ecosystem of Xiaomi or Yandex.

1. Automatic scripts in Mi Home

Example scenario: "If the humidity is below 40%, turn on the humidifier at an average speed."

• Open Mi Home → “Automation” → “Add”
• Select the condition: “Humidity < 40%" (use a sensor such as Xiaomi Temperature and Humidity Sensor).
• Add the action: "Enable the humidifier by 50%."
• Save the script.

2.Integration with Yandex Smart Home

You can create a chain of actions, such as, Alice, good night» → turn off the lights, turn on the humidifier at minimum speed and start the “white noise” on the column.

• Open Yandex Smart Home → “Scenarios” → “Create a script”.
• Add devices and commands (such as a humidifier) + smart-light).
• Assign a voice command.

3. Manage through Home Assistant (for advanced)

If you use Home Assistant, you can connect the humidifier via the Xiaomi Miio component:

# Configuration for Home Assistant (fragment)


climate:




- platform: xiaomi_miio




name: "Xiaomi Humidifier"




host: 192.168.1.100 # IP- Utilizer address




token: YOUR_DEVICE_TOKEN #Token from Mi Home

To receive the token, use the Mi Home Token Extractor app (available on GitHub).

⚠️ Note: When using Home Assistant, disable Yandex Smart Home integration to avoid team conflicts.

7 Updates and Compatibility: What Changed in 2026

In 2026, Xiaomi released several humidifier updates that affected their work with Alice.

1 New models with Matter support

• Smartmi Air Humidifier 3 and later supports Matter protocol, which simplifies integration with Yandex Smart Home and other platforms (for example, Google Home).
• To connect via Matter, it is enough to scan QR-code on the device in Yandex Smart Home.

2. Changes to Mi Home authorization

• Since 2026, Xiaomi has tightened security requirements: confirmation of the linking of accounts may be required SMS email.
• If there is an error in the authorization process, check if yours is blocked. IP-Address (especially relevant when used) VPN).

3. Updated voice commands

• Alice now supports commands with running times, such as, "Alice, turn on the humidifier for 2 hours."
• For models with backlight added the command "Alice, turn on the light on the humidifier".

FAQ: Frequent questions about connecting Xiaomi moisturiser to Alice