Xiaomi Mi Robot Vacuum-Mop G1 is a smart device that requires the right initial setup to work. Many users face difficulties already at the connection stage: the application does not see the vacuum cleaner, Wi-Fi does not connect, there are synchronization errors. In this article, we will analyze all the stages of connection from unpacking to the first cleaning, taking into account the current versions of the firmware and the Mi Home application for 2026.
The G1 has a different feature than previous generations, which is hybrid cleaning (vacuum cleaner + mop) and improved navigation sensors, but these same features require more careful tuning, and if you buy a used vacuum cleaner or drop it to factory settings, the manual will also work — we will give you all the nuances for such cases.
Important: the connection process may vary depending on the region of purchase (China, global version) and the firmware version.
Preparation for the first launch: unpacking and testing of the complete set
Before you plug in, make sure the box has everything you need. The standard Xiaomi G1 includes:
- 🤖 Robot vacuum cleaner with brush installed and dust tank installed
- ⚡ Charging station (dock station) with a power supply unit
- 📄 Multilingual instruction (global version)
- 🔧 Care kit: spare brushes, filter HEPA, napkin for sensors
- 🧹 Water reservoir (if model supports wet cleaning)
First, check the vacuum cleaner case for damage.
- 🔍 Sensors (front and bottom) - they must be clean, without protective films.
- 🔋 Charging contacts on vacuum cleaner and docking station - check if there is oxidation.
- 🌀 Wheels and brushes -- they should rotate freely.
💡
If you bought a used vacuum cleaner, be sure to replace the HEPA- filter and wash the water tank (if any) - the previous owner could use aggressive detergents that will damage the new seals.
Also check the serial number on the bottom of the vacuum cleaner, which you'll need to anchor in the app. If the number is erased or missing, it could be a sign of a replica. Original Xiaomi devices always have clear labeling.
Installation of the docking station and first activation
The proper placement of the charging station is the key to the stable operation of the vacuum cleaner.
- 📏 Distance from walls: at least 50 cm on each side and 1.5 m in front.
- 🚪 Doors and passageways: The station must stand in a zone with minimal traffic (not on the aisle).
- ☀️ Lighting: Avoid direct sunlight — they can damage the IR sensors.
- 🔌 Socket: Use the original power supply (5V/2A). Connecting via the extension cord may cause charging errors.
After installation of the station:
- Connect the power supply to the socket.
- Put the vacuum cleaner on the station - it should emit an audible signal and start charging (the indicator will flash white).
- Wait until the indicator is blue (full charge) or at least green (partial charge). 20% charge is enough for the first turn on.
Put a vacuum cleaner in the dock.|I connected the power supply to the socket.|Heard the beep.|The indicator flashes white/blue|Charge at least 20%-->
If the vacuum cleaner is not operated:
- 🔋 Check the contacts to the station and vacuum cleaner - they should match.
- 🔌 Try another outlet (without the extension cord).
- 🔄 Press and hold the power button on the vacuum cleaner for 10 seconds to reset.
What to do if the indicator flashes red?
3. Wi-Fi connection: step-by-step instructions
To control the vacuum cleaner via your smartphone, you need to connect it to your home Wi-Fi network. Use only 2.4 GHz – Xiaomi G1 does not support 5 GHz. If your router is dual-band, temporarily turn off 5 GHz or create a separate network for 2.4 GHz.
Connection steps:
- Download the Mi Home app (App Store/Google Play). For China, use Mi Home China.
- Sign up or sign in to your Xiaomi account (required!).
- Click + → Add Device → Household Care → Mi Robot Vacuum-Mop G1.
- Choose the region: China (if the vacuum cleaner is from China) or Russia/Europe (for the global version).
- Hold the Power + Home buttons on the vacuum cleaner for 3 seconds until you hear a voice message in Chinese ("Wi-Fi connected").
- In the app, select your Wi-Fi network (2.4GHz!) and enter a password.
If the vacuum cleaner is not connected:
| Problem. | Reason. | Decision |
|---|---|---|
| App doesn't see vacuum cleaner | The vacuum cleaner is not paired | Repeat button retention Power + Home until the beep |
| The "wrong password" error | Special characters in the Wi-Fi password | Change your password to Latin without characters (!@#, etc.) |
| Connection is interrupted by 99% | Weak Wi-Fi signal | Move the router closer or use a repeater |
| The message "The device is not supported in your region" | Mi Misconceptions in Mi Home | Remove the device and add it back with the right region |
Important for the Chinese version: if the vacuum cleaner is purchased in China (for example, on AliExpress), it must be linked to the Mi Home account in China, then you can change the region in the application settings to your own, but the initial binding should be to the Chinese server.
4.Setting up in the Mi Home application: basic parameters
Once the device is successfully connected, the vacuum cleaner will appear on the list of devices, and now you need to configure the key parameters:
- 📍 Room map: Start the first cleanup in Full Cleanup mode so that the vacuum cleaner can make a map. Don't interrupt the process!
- 🚫 Prohibited areas: Mark places on the map where the vacuum cleaner should not go (such as children's toys or wires).
- 🕒 Schedule: Set up automatic cleaning for a convenient time (optimally when you are not at home).
- 🔊 Voice Alerts: Turn off if they interfere (in vacuum cleaner settings).
For wet cleaning (if supported):
- Fill the water tank with distilled or boiled water (ordinary water can leave a stain).
- Install a napkin for washing floors (comes with the kit).
- In the application, select the Wet Cleaning mode and adjust the intensity of the water supply (for laminate - minimum).
💡
Always start the first cleaning in the “Full cleaning” mode – this will allow the vacuum cleaner to accurately map the room and avoid collisions in the future.
If the map is built incorrectly (skips rooms, displays walls incorrectly):
- 📱 Check the height of the vacuum cleaner installation – the sensors should be at 10-15 cm from the floor.
- 💡 Make sure there is enough light in the room (laser sensors work worse in the dark).
- 🧲 Avoid metal surfaces near the docking station — they may distort the signal.
5. Firmware Update: Why It Matters and How to Do It
The Xiaomi G1 firmware is regularly updated, with navigation bugs fixed, new cleaning modes added.
- Open Mi Home → select vacuum cleaner → Settings → Update firmware.
- If a new version is available, click Update.
- Don't interrupt the process! The vacuum cleaner will restart automatically.
What the latest firmware gives (2026):
- ✅ Improved navigation in dark spaces.
- ✅ Support for Alice's voice (for Russian users)
- ✅ Water consumption optimized for wet cleaning.
What happens if you interrupt the update?
If the update is hanging:
⚠️ Warning: If the vacuum cleaner freezes in Prepare for Upgrade for more than 20 minutes, restart it manually (hold the power button 10 seconds) and try again. If the error repeats, reset to factory settings (see FAQ).
6. Frequent errors and their solutions
Even after a successful connection, there can be problems.
| Mistake. | Reason. | Decision |
|---|---|---|
| The vacuum cleaner is not returning to the station | Weak signal of an IR beacon or obstacle | Check if there are any objects in front of the station. |
| Does not wash the floor (dry cleaning works) | Clogged pump or not installed napkin | Wash the water tank, check the tubes. |
| He keeps saying "Stuck." | High threshold or dark carpet | Install virtual walls in the app or use magnetic tape. |
| Not connected to Wi-Fi after reset | Cash nets in the vacuum cleaner | Forget the network in the router settings and connect again. |
If the vacuum cleaner starts knocking or buzzing loudly:
- 🌀 Check the side brush, it may have been wound with hair.
- 🗑️ Clean the main filter and the dumpster.
- 🛠️ Examine the turbine fan for foreign objects.
For diagnosis, use the Mi Home error log: Vacuum Settings → Journal → Errors. This lists the fault codes (e.g., Error 10, wheel problem).
7. Smart Home Integration: Alice, Google Assistant, Home Assistant
Xiaomi G1 supports control through voice assistants and smart home systems.
- 🗣️ Yandex Alice: Open the Yandex app → Devices → Add → Xiaomi. Sign in through your Mi Home account. Say, "Alice, turn on the vacuum cleaner."
Google Assistant:
- In Mi Home, go to Profile → Settings → Voice Assistant → Google Assistant.
- Follow the instructions for linking accounts.
Home Assistant will require:
- Install the Xiaomi Miio component.
- Get the device token through Mi Home (use this script).
- Add configuration to configuration.yaml: vacuum: - platform: xiaomi_miio host: IP_ADRESS DUST TOKEN: YOUR TOKEN
If the vacuum cleaner is not displayed in a smart home:
⚠️ Warning: To integrate with Alice or Google Assistant, the vacuum cleaner must be linked to a Mi Home account in the region of Russia or Europe. Chinese accounts are not supported!