Connection of Xiaomi aerogrill to Wi-Fi: full instructions with error analysis

Xiaomi air grills are not just kitchen appliances, but full-fledged smart home ecosystem devices that can be controlled from a smartphone, customized recipes remotely and received notifications of readiness of dishes. However, the first connection to Wi-Fi often causes difficulties: the application does not find the device, the router does not see the aerogrill, or the process is frozen in synchronization. In this article, we will analyze all official and alternative ways of connecting, as well as typical errors that prevent successful configuration.

It is important to understand that the connection algorithm may differ depending on the aerogrill model (e.g. Xiaomi Mi Smart Air Fryer). 3.5L vs. Xiaomi Mijia Air Fryer Pro) and firmware versions.We will focus on the universal methods that work for most Xiaomi devices from 2022-2026.If your aerogrill is released earlier, check the relevance of the firmware - you may need an update.

Before you start, make sure you have:

• 📱 Smartphone on Android 8.0+ or iOS 12+ with the Mi Home app installed (or Mi Fit for some models).
• 🔌 220V running socket – the aerogrill must be connected to the network at the entire connection stage.
• 📶 Wi-Fi-enabled router 2.4 GHz (5 GHz not suitable for most Xiaomi devices).
• 🔐 Password from your Wi-Fi network (if the network is hidden, you will need its name — SSID).

1. Router Preparation: Why the Air Grill is Not Connecting to Wi-Fi

In 60 percent of cases, connection problems are not due to the aerogrill itself, but to the router's incorrect settings, and Xiaomi devices have strict network requirements:

First, the aerogrill doesn't support 5 GHz networks -- only 2.4 GHz. If your router is broadcasting on two frequencies simultaneously under the same name (SSID), The solution is to split networks in the router settings or temporarily disable 5 GHz.

Second, some routers use customer isolation (AP Isolation) or filtration by MAC-Check these settings in the router’s web interface (usually at 192.168.0.1 or 192.168.1.1) and disable them while you configure them.

Also note:

• 🔄 Network operation: should be 802.11 b/g/n (regime 802.11n only may not be supported).
• 🔒 Type of encryption: only WPA2-PSK (AES). Obsolete. WEP mixed WPA/WPA2 won't fit.
• 📡 Signal power: If the router is far from the kitchen, the signal may be too weak.

⚠️ Note: If your router is using a dynamic router DNS (For example, from the provider and often changes the local IP-Address, the aerogrill may lose connection. IP device DHCP-reservation.

2. Step-by-step instruction: connection via Mi Home

The main way to connect is through the official Mi Home app (download for Android or iOS).

Step 1: Install and open the Mi Home app. Sign in with your Xiaomi account (if you don't have one, sign up) Importantly, the account must be linked to the same region as your aerogrill (usually China Mainland, Russia or Europe) to change the region:

1. Go to Profile → Settings → Region.
2. Choose the right region (for example, Russia).
3. Leave the account and log in again.

Step 2. Press Add the device (+) In the search box, type the name of your aerogrill model (e.g. Mi Smart Air Fryer) or select the Kitchen category. → airgrill.

Step 3. Follow the instructions on the screen:

Turn the aerogrill into the socket and press the power button.|Make sure the Wi-Fi indicator flashes blue.|Bring the smartphone closer to the aerogrill (at a distance) < 1m)|Enter the Wi-Fi password in the application|Wait for the sound signal (1 short beep) = succession)-->

If the process is suspended at the Connection stage:

• 🔄 Reboot the aerogrill (remove the plug from the socket for 10 seconds).
• 📱 Restart the Mi Home app and try again.
• 🔌 Try another power source (sometimes connecting through a network filter helps).

⚠️ Warning: If the aerogrill emits 3 long beeps in a row, this means an error in connecting to Xiaomi servers. Check the Internet connection on your smartphone (turn off). VPN, If it is on, try again in 5 minutes.

3. Alternative ways of connecting

If the standard Mi Home method didn’t work, try one of these options:

Method 1 Connect via Mi Fit (for some models)

Some Xiaomi aerogrills (e.g. Mijia Air Fryer Pro) support connectivity via the Mi Fit app, which is commonly used for fitness bracelets.The algorithm is similar to Mi Home, but the interface may differ.

1. Open Mi Fit and go to Profile → Add the device.
2. Choose the category Smart Home.
3. If your model appears in the list, follow the instructions.

Method 2: Mode AP (point).

If the aerogrill does not find your network, you can connect to it directly through the access point mode:

1. Press the Wi-Fi button on the air grill for 5 seconds until the indicator flashes quickly.
2. On your smartphone, open your Wi-Fi settings and connect to the network with a name XIAOMI-XXXX (password not required).
3. Return to Mi Home and re-add the device.

Method 3: Reset to factory settings.

If previous methods did not help, perform a hard reset of aerogrill:

1. Disconnect the device from the network.
2. Press the power button and hold it for 10-15 seconds.
3. Connect the aerogrill back - it should emit an audible signal and reset all settings.

4. Common mistakes and their solutions

Even with the right router setup and following the instructions, users face typical errors.

Error: "Device does not respond" (in the Mi Home app).

Reasons:

• 🔌 The aerogrill doesn't get enough power (try another socket).
• 📱 Smartphone connected to mobile Internet instead of Wi-Fi.
• 🛡️ Firewall or antivirus blocks the connection (temporarily disable them).

Error: “Not able to get the device token.”

This error is related to problems on Xiaomi servers.

• 🔄 Reboot router and air grill.
• 🕒 Wait 10-15 minutes and try again (servers may be overloaded).
• 🌐 Check if your provider is blocking access to api.io.mi.com and ot.io.mi.com domains (relevant to some corporate networks).

Error: The aerogril connects but does not appear in the app.

Possible causes:

• 📍 The device is linked to another Xiaomi account (for example, if you bought it used.
• 🔄 Mi Home has LAN Only enabled. Turn it off in your device settings.
• 📶 The aerogrill is connected to the network, but does not have access to the Internet (check the settings of the router).

💡

If the aerogrill is connected, but constantly disconnects, try fixing the router settings in the router settings. MAC-fixed-point IP. It's gonna prevent conflict. DHCP.

5.Configure after connecting: what can be done through the application

After a successful connection to Wi-Fi, the Xiaomi air grill will open access to advanced features:

Recipe management.

The Mi Home app offers pre-installed programs for different dishes (french fries, chicken wings, pastries, etc.) and you can:

• 📝 Edit the time and temperature for each recipe.
• ⏱️ Save your own settings as custom recipes.
• 🔄 Start cooking remotely (for example, warm up the aerogrill on the way home).

Notification and monitoring.

The app will send push notifications:

• 🔔 When the dish is ready.
• ⚠️ If the temperature is higher than normal (overheating protection function).
• 🔋 On low charge (for models with a battery, for example, Xiaomi Mi Smart Air Fryer Portable).

Integration with the smart home ecosystem.

The aerogril can be linked to other Xiaomi devices:

• 💡 With smart lamps: for example, turn on the kitchen light when starting cooking.
• 🔊 With the Xiaomi column: voice notifications about the status of the dish.
• 📱 With motion sensors: automatically turn on the aerogrill when you appear in the kitchen.

To set up automation go to Mi Home → Automation → Create a script.

💡

To ensure that the air grill works smoothly over Wi-Fi, update the device firmware and the Mi Home app to the latest versions. Outdated versions of the software often cause failures.

6.Security: How to protect an air grill from hacking

Connecting kitchen appliances to Wi-Fi always raises security questions, and here are the mandatory steps to protect your air grill:

1. Use a complex Wi-Fi password.

Passwords must contain at least 12 characters, including letters, numbers and special characters, and avoid simple combinations like 12345678 or qwerty.

2. Set up a guest network for smart devices.

Create a separate network for a smart home with limited access to local resources, for example, on TP-Link routers, this is done in the Guest Network section.

3. Turn off remote access if you are not using it.

In the aerogrill settings in Mi Home, you can prevent control from outside your local network:

1. Go to the Device. → Settings → Network settings.
2. Turn off the Remote Access option.

4. Update the firmware regularly.

Manufacturers often release security patches to check the relevance of the firmware:

1. Open Mi Home and select your aerogrill.
2. Go to Settings → Update firmware.
3. If a new version is available, install it.

⚠️ Warning: If you sell or transfer an aerogrill to another person, be sure to reset it to factory settings and unplug your Xiaomi account.

7. Frequent questions and answers