Modern automatic cleaning devices make life much easier, but even the most advanced Roborock S6 requires regular maintenance. Many owners mistakenly believe that the gadget works autonomously for months, forgetting about the accumulation of dust and debris in hidden compartments. Ignoring basic care can lead to reduced traction, the appearance of extraneous noises and even break expensive mechanisms.
In this article, we will discuss in detail how to clean Xiaomi Roborock S6 at home without going to the service center. HEPA-The filter, the correct washing of the container and maintenance of the side brush.Adhering to these simple rules will prolong the life of your smart assistant and keep the quality of cleaning at the highest level.
Before you start any manipulations, be sure to turn off the device. Turn over the robot and find the power button, which is usually hidden under the lid or located on the side panel. Complete power off is necessary to ensure the safety of the electronics and prevent accidental start of the motors during the procedure.
Preparation for maintenance and safety
Any technical procedure starts with the preparation of the workplace. You'll need a clean, dry surface, soft microfiber fabric, a dry brush and perhaps wet wipes without alcohol.
⚠️ Warning: It is strictly forbidden to wash the main body of the robot under the tap or immerse it in water. Internal electronics have no moisture protection, and even a small amount of liquid can cause a short circuit.
It is recommended to maintain the container immediately after the cleaning cycle is completed, until the dust in the container has had time to compress very much. If you use a model with wet cleaning function, make sure that the electronic tank is completely empty before cleaning.
For effective work, prepare the following tools:
- 🧹 Dry soft brush to remove dust from hard-to-reach places.
- 🧼 Microfiber for wiping sensors and body.
- ✂️ Scissors or a special knife to clean the main brush from hair.
- 💧 Distilled water (only for filter washing if reusable).
Make sure you have access to the bin to dispose of the container's contents immediately. The dust collected by the robot contains microparticles that you don't want to re-inhale, so try not to raise a cloud of dust when you remove the container.
Cleaning the main dust container
The dust container is the heart of the garbage collection system in the Xiaomi Roborock S6. Over time, small fractions of dust clog the output holes, which critically reduces the suction force. To extract the container, press the fixation button on top and smoothly pull up. Don't put too much effort into it, the mechanism is designed to open with a light motion.
Empty the container after each cleaning. Even if it's only a quarter full, it's better to dump the garbage to ensure optimal air circulation. Inside the container, you might notice a mesh filter of rough cleaning, and it needs to be gently knocked out with light taps on the wall of the garbage can.
☑️ Checklist for container cleaning
If plaque or sticky contamination forms on the walls of the container, it can be washed with water, but this should be done with extreme care:
- 💦 Wash only the plastic case, avoiding water on rubber seals and mechanical flaps.
- 🚫 Do not use hot water as it can deform plastic.
- ⏳ Before you put it back into the robot, make sure you dry the container completely. The wet plastic attracts the dust, turning it into dirt.
Pay special attention to the inlet through which the dust enters the container. Animal hair and fur are often wound up there, forming a dense lump; Use tweezers or scissors to carefully remove these impurities. A clogged inlet is a common cause of errors, "The container is full," even when it is empty.
Service HEPA-filtering and filtration systems
Roborock filtration system S6 It includes highly effective HEPA-It's a filter that traps the smallest particles of allergens, and many users make the mistake of washing this filter under the tap. HEPA-The water destroys the fiber structure, and the filter stops trapping the dust, allowing it back into the air and into the motor.
Use a dry brush to clean the filter. Carefully stubble through the folds of the filter, removing surface dust. If the filter is heavily contaminated and blackened, it is better to replace it with a new one. The resource of one filter is usually from 2 to 4 months of active use, depending on the dustiness of the room.
⚠️ Warning: Installing a wet or undried filter will cause moisture to enter the engine turbine, causing corrosion and the device to fail.
In some trim levels or when using reusable filters (for example, foamed material), you can clean clean.
- Wash the filter under a weak stream of cold water without detergents.
- Shake the excess water, but do not squeeze or twist the filter.
- Leave to dry at room temperature for at least 24 hours.
How often do I change the filter?
Regularly changing the filter is not only about keeping the air clean, it's also about protecting the engine. A clogged filter creates air resistance, causing the engine to work at higher loads, which reduces its lifespan.
Care for a side brush and main roller
The side brush in the Xiaomi Roborock S6 is actively involved in collecting debris from the walls and corners. It is attached to a special holder with a single screw. To remove the brush, use a screwdriver or coin that is included in the kit. The axis of the brush often wraps hair, which over time can block the rotation mechanism.
The main roller (turbobrush) is the main working element. The S6 uses a brushless silicone roller, which confuses hair less, but still requires attention. To remove it, press the locks on the sides of the casing and pull the roller up. Clean it of the wound threads and hair.
For high-quality cleaning of the roller, perform the following actions:
- ✂️ Carefully cut off the wound hair with scissors, trying not to damage the silicone slats.
- 🧽 Wipe the roller with a wet cloth to remove sticky dust.
- 🔍 Check the bearings from the ends of the roller - they should rotate freely.
💡
Use a razor blade or a special knife from the kit to carefully cut tightly wound hair along the axis of the roller, which will speed up the cleaning process at times.
Remember to clean the niche where the roller is placed. There's often a lot of debris that can get into bearings or block movement. Blow this compartment or brush it. The cleanliness of the mechanical parts directly affects the quality of carpet cleaning.
Cleaning of wheels, sensors and charging station
The Roborock S6's navigation is built on a laser rangefinder (LDS) and a host of optical sensors. If the sensors are contaminated, the robot can fall down stairs, get stuck on the doorsteps, or move around the room randomly. Wipe all the black sensor windows (below and bumper) with a dry microfiber.
Wheels also require inspection. Wool and dust are often stuffed between the wheel and the body, which can make it difficult to walk. Try to spin the wheels with your hand - they should move with light resistance, but not be clamped. Use a toothpick or a thin spoke to clean the gaps.
The charging station is another element that is forgotten, and the contacts on the station and on the robot can become oxidized.
| Element | Frequency of cleaning | Cleaning method |
|---|---|---|
| Charging contacts | Once every 2 weeks | Dry cloth or eraser |
| Laser rangefinder (tower) | Once a month | Dry brush/tissue |
| Wheels. | Once a month | Hair removal, wiping. |
| Floor sensors (bottom) | Once a week. | Dry microfiber |
Pay special attention to the laser rangefinder on the top panel. Gently wipe the transparent window of the tower. If there is dust on the lens inside the tower (visible through the slots), you can try to blow it off with a pear to clean the optics, but it is not recommended to disassemble the tower yourself.
Software cleaning and error resetting
In addition to physical cleaning, the Xiaomi Roborock S6 requires attention at the software level, and in the Mi Home or Roborock app, you can check the status of filters and reset the meter if you replace the consumables, which will allow the system to correctly calculate the remaining resource.
Sometimes, after cleaning, the robot can make mistakes or behave strangely, in which case a software reset helps, which requires you to press the on and home buttons (or the spot button, depending on the firmware version) at the same time for 5-10 seconds before the beep, which will restart the system without losing the maps of the premises.
⚠️ Warning: Full factory reset (via button combination or app) will remove saved room maps. Use this feature only if you are moving the robot to a new home or if the map is not built correctly.
Also check for firmware updates. Xiaomi engineers regularly release patches that improve the algorithms for bypassing obstacles and working with carpets. You can run the update through the settings menu in the application: Settings → About device → Check for updates.
💡
Regular firmware updates can correct navigation errors that users often mistake for sensor breakdowns.