How to untie the remote from the chandelier Xiaomi: all working methods

Xiaomi Smart Chandeliers (including Mi models) LED Ceiling Light, Yeelight and Mijia Smart Lamp all allow you to control lighting via a smartphone or a physical remote control, but over time, you may need to untie the remote from the chandelier — for example, when selling a device, crashing or connecting a new remote. Unlike traditional chandeliers, where it is enough to remove the batteries, Xiaomi smart devices require special actions to reset the pairing.

In this article, we will analyze all the current ways of decoupling the remote – from software methods through the Mi application. Home/Yeelight We will pay special attention to the nuances that the manufacturer does not always mention in the official instructions: what to do if the chandelier does not respond to commands, how to avoid accidental resetting of all settings and why some remotes RF 2.4G They require additional manipulation.

Note: The instructions are relevant for Xiaomi chandeliers of all generations (2018–2026), but may differ for firmware devices CN (If your model uses the Zigbee protocol (for example, Mijia Smart Ceiling Light Pro), you will need a Xiaomi Gateway - read about this in a separate section.

1.Preparation: What to Know Before Untangling the Remote

Before proceeding with the resetting of the pairing, make sure that:

• 🔋 The chandelier is connected to the network 220V and on (even if not shining - power on the control board should be served).
• 📱 You have the current Mi Home app installed (version 6.+.+) Yeelight (for the respective models).
• 🔄 The remote you want to untie is within the range of the chandelier (up to 10 meters for the chandelier). RF 2.4G).
• 📡 If the chandelier is connected to Wi-Fi, check the stability of the network – a connection break during a reset can lead to a device lock.

Important point: some Xiaomi chandelier models (e.g. Yeelight) YLXD01YL) They retain the remote's binding in non-volatile memory, which means that even after the power is turned off, the pairing does not automatically reset).

⚠️ Note: If the chandelier is controlled through the Xiaomi Gateway (Zigbee protocol), untying the remote via the application can lead to the removal of the device from the smart home network.

2. Method 1: Untie the remote via the Mi Home application

The safest and most recommended method is to use an official app, which is suitable for most models, except those running through Zigbee (section 5).

Step 1. Open Mi Home, go to the Devices tab, and select your chandelier. If the device doesn't show up, check the connection to the same Wi-Fi network as the phone.

Step 2. In the chandelier card, tap on the three-point menu (⋮) in the upper right corner and select Device Settings → Control of remotes (or remote control, depending on the firmware version).

Step 3. In the list of interfaced remotes, find the one you want to delete and click Untie (or basket icon). Confirm the action.

If there is no control point:

• 🔄 Try updating the chandelier firmware through Settings → Update of the PO.
• 📱 Remove and re-add the chandelier to the app (Section 6).
• 🔧 For Yeelight models, use the Yeelight proprietary application – the algorithm is similar.

⚠️ Attention: After untieing the remote via Mi Home, some models of chandeliers (Mi) LED Ceiling Light 4 and later may require a reboot. To do this, disconnect the chandelier from the network for 10 seconds, then turn it on again.

Method 2: Hardware reset by buttons on the chandelier

If the remote is not untied through the app or the chandelier is not connected to Wi-Fi, use physical buttons on the device body. This method works for most models except the Yeelight Moon and Mijia Smart Lamp Pro (they need a different algorithm - see section 4).

Instructions for chandeliers with reset button:

1. Turn off the chandelier from the network for 5 seconds, then turn it on.
2. Within 3 seconds after turning on 5 times quickly press the power button on the chandelier body (usually it is hidden under the decorative panel).
3. The chandelier will blink 3 times - this is a signal to switch to reset mode.
4. Hold the power button for 10 seconds until the chandelier blinks 1 time long (resetting the interface of the remote).

For models without a reset button (e.g., Mi) LED Ceiling Light 2):

1. Turn off the chandelier.
2. Press the power button and, without letting it go, connect the chandelier to the network.
3. Hold the button for 15-20 seconds until the flashing appears.

Critical: if the chandelier flashes red after resetting, this indicates an error: repeat the procedure or check the integrity of the wiring (possibly the voltage in the network is unstable).

Method 3: Forced reset to factory settings

If previous methods fail, you'll have to completely reset the chandelier, which will remove all settings, including the Mi Home account binding and the associated remotes, and only use this as a last resort!

The algorithm for most models:

1. Turn off the chandelier for 30 seconds.
2. Turn on the chandelier and within 5 seconds 7 times quickly press the power button.
3. The chandelier will start flashing yellow – hold the 10 seconds button until a white light (reset signal) appears.

For Yeelight chandeliers (e.g, YLXD02YL):

1. Turn on / off the chandelier 5 times in a row (the interval between inclusions is 2 seconds).
2. Hold the 5-second button for the 6th time.
3. After resetting the chandelier will emit an audible signal (if there is a speaker).

⚠️ Note: After the chandelier is completely reset, Xiaomi may stop showing up in Mi Home. To re-add it, go to Add Device → Lighting → Choose a model and follow the instructions. Zigbee models will require a gateway.

💡

If the chandelier does not turn on after reset, check the fuse on the control board. In 80% of cases, the problem is solved by replacing the fuse with a safety lock. 250V 2A.

5. Features of detachment of remotes for chandeliers with Zigbee (through the gateway)

Chandeliers running on the Zigbee protocol (for example, Mijia Smart Ceiling Light Pro or Yeelight with Zigbee) require a Xiaomi Gateway.

Step 1: Make sure the Gateway is connected to the network and operates in the same ecosystem as the chandelier (e.g., both devices are tied to the same region in Mi Home – China, Europe or Russia).

Step 2. In the Mi Home app, go to the gateway settings, then select Zigbee Devices → find your chandelier.

Step 3. Slip on the chandelier, select Device Settings → Control remotes. In the list of associated devices, find the remote and press Delete.

If the remote is not displayed:

• 🔄 Reboot the gateway (turn off power for 1 minute).
• 📡 Check the distance between the lock and the chandelier - it should not exceed 15 meters (no obstacles).
• 🔧 Update the gateway firmware through Settings → Update of the PO.

Important: After the remote is untied through Zigbee, you may need to reconnect the chandelier to the gateway. To do this, press and hold the button on the chandelier for 5 seconds until it starts flashing.

6 How to Re-Add a Chandelier to Mi Home After Resetting

If you complete the reset (section 4), you'll have to reconnect the chandelier to the application.

For chandeliers with Wi-Fi (Mi) LED, Yeelight is standard):

1. In Mi Home, click Add Device (+) → Lighting.
2. Choose your chandelier model from the list.
3. Connect to the temporary Wi-Fi network that the chandelier will create (the name will be type) yeelink-light_XXXX).
4. Return to the app and wait for the setup to be completed.

For chandeliers with Zigbee (through the gateway):

1. Make sure the Gateway is on and connected to Mi Home.
2. In the app, select Add Device → Through the lock.
3. Press and hold the button on the chandelier for 5 seconds until it blinks.
4. The gateway must automatically detect the device.

If no chandelier is added:

• 🔌 Make sure it is getting enough power (network voltage) 220V ±10%).
• 📶 Switch your phone to the mobile Internet (sometimes the router blocks temporary network devices).
• 🔄 Try to drop the chandelier again (Section 4) and repeat the addition.

💡

If the Yeelight chandelier doesn’t connect to Wi-Fi, try using the Yeelight app instead of Mi Home – it often works more stable for this series.

7. Frequent mistakes and how to avoid them

When you untie the remote, you often have a problem that's typical, and here's how to solve it:

Error 1: The chandelier does not respond to the reset buttons.

• 🔌 Check that the chandelier is receiving power (the indicator on the board should burn).
• 🔧 If the button "sparks", carefully remove it with tweezers and clean the contacts.
• 🔄 For models with a touch button, try pressing with two fingers (sometimes the sensor requires closer contact).

Mistake 2: The remote has untied, but the chandelier has stopped working.

• 📱 Check if the chandelier has been removed from the Mi Home. Add it again if necessary (Section 6).
• 🔋 Maybe the brightness settings are lost - reset them through the app.
• 🔌 If the chandelier does not turn on at all, check the fuse (section 4).

Error 3: The new remote does not match.

• 🔄 Make sure the old remote is completely untied (check in Mi Home).
• 📡 For remotes. RF 2.4G the distance to the chandelier should not be more than 5 meters.
• 🔋 Reset the chandelier (turn off power for 30 seconds).

Error 4: There is no "Control Control" item in the appendix.

• 📱 Update Mi Home to the latest version.
• 🔧 Check your account region – some features are only available in China or Europe.
• 🔄 Try using the Yeelight app (for the relevant models).

8. FAQ: Answers to frequent questions