How to Open a Xiaomi Soap Container: Full Instruction

Xiaomi Mijia automatic dispensers have become an integral part of the modern bathroom, providing hygienic and contactless application of soap. However, owners often face a situation where a standard replacement of the cartridge does not solve the problem, and there is a need for full access to the inner compartment.

The process of opening the case is not trivial, as manufacturers deliberately hide fasteners to maintain aesthetic appearance and moisture protection. Incorrect application of force can lead to breakage of plastic latches or damage to the silicone pad, which will permanently disable the device. In this material, we will discuss in detail the algorithm of actions for the safe dismantling of various models of dispensers.

Before you start disassembling, you need to clearly understand what kind of modification you are dealing with. The line includes classic versions with an IR sensor, models with foaming and newer devices with adjustable supply volume. The design of their bodies may differ in the location of screws and type of connections, so there is no universal method for “all-in-a-lifetime” but the general principles remain similar.

Preparation of the workplace and tools

To successfully complete the disassembly task, you will need a minimum set of tools that can be found in the drawer of any home craftsman. The main requirement is accuracy, since the plastic used in the Xiaomi Smart Soap Dispenser is quite thin and fragile. Using inappropriate items such as knives or wide screwdrivers often causes chips and scratches on the front panel.

The best tool to get started is a thin plastic card or a special mediator for opening electronics. Metal tools should be used with extreme caution only if plastic counterparts can not cope with latches. You will also need a small cross screwdriver (usually PH0 or PH00) and a container for collecting small screws, which tend to be lost at the most inopportune moment.

💡

Before starting disassembly, be sure to remove the batteries or disconnect the device from charging to avoid short circuits when the tools come into contact with the control board.

It is important to ensure good lighting of the work area. Inside the case are small plumes and contacts that are easily damaged when visibility is low, prepare a soft fabric or silicone mat to put the removed parts of the case and not scratch their glossy surface during operation.

Dismantling the outer cover and searching for hidden screws

The first step is always to remove the top decorative panel or tank cover. In most Mijia Automatic Induction Soap Dispenser models, the top is held on the friction latches. You take the device in one hand, and the second one is to gently tweak the edge of the lid in the nozzle or indicator area. A characteristic click will indicate successful latch break.

Once the lid is removed, you will see a battery compartment and possibly screws hidden under a rubber plug. In some versions, especially in the foam versions, the fasteners can be hidden under a sticker with a logo or specifications. Carefully examine the inner surface of the case - screws can be located not only on top, but also in the bottom of the glass, closer to the pump mechanism.

If the screws are found, they need to be twisted counterclockwise. Don't make excessive efforts: if the screw does not lend itself, it may be filled with glue or covered with a factory lacquer, in which case you can carefully warm the screw head with a hairdryer at low temperature for 10-15 seconds to soften the lock.

Separation of the shell and access to the pump mechanism

Once all visible fasteners are removed, the most critical thing is to separate the main body, and the design often involves internal plastic hooks around the perimeter, and to release them, you need to use a thin tool along the junction of the two halves of the body, sequentially snapping the locks.

Go in a circle, starting from the bottom and going up. Don't try to pull the halves apart with a jerk, because that's guaranteed to break one of the hooks. The soap feed mechanism is connected to the electronic board with a thin plume, so a sharp movement can cut the contacts. Disconnect the case slowly, controlling the tension of the internal connections.

⚠️ Warning: Inside the case, there may be a silicone gasket that seals the battery compartment, and if it is not opened carefully, it may dislodge or break, which in the future will lead to moisture on the contacts.

When the halves of the body are separated, you have full access to the pump and the engine, and this is where dried soap residues most often accumulate, which block the piston from working, and you can use cotton swabs dipped in warm water or a weak vinegar solution that dissolves alkaline deposits well.

Cleaning of sensors and fluid supply tubes

One of the main reasons users decide to open the container is because the tubes are clogged or the sensor fails.The infrared sensor responsible for the response to the hands is located in the front of the device and can become contaminated with soap plaque.

The fluid intake tube running from the bottle neck to the pump also requires attention. If it is clogged, the device will buzz, but not soap. You can use thin wire or blow the tube with air to clean. In models with foaming, it is important to check the mesh filter at the end of the tube - it must be washed under running water until the contaminants are completely removed.

Pay special attention to the area where the motor and gears are connected, and often there is a porridge of dried soap and dust that makes it difficult to rotate. Mechanical cleaning of this area usually returns the device to the factory noiselessness and efficiency. After cleaning, let all the parts dry completely before assembly.

Comparison of Xiaomi Dispensers Models

Different generations of devices have design features that affect the disassembly process, and understanding these differences will help you avoid mistakes and choose the right tool for your particular model.

As you can see from the table, the approach to each model is different: if you have a version of the Foam Hand Washer, the main mechanism is hidden inside the glass that you need to twist, whereas the classic versions require you to find screws under decorative elements.

Assembly and seal check

After all the necessary cleaning or repairing procedures, the assembly phase is done in reverse order: first, the halves of the body are connected, then the plumes are connected and the screws are twisted, and it is important to make sure that all the wires are placed in their slots and not clamped during assembly.

When you build it, you should pay special attention to the silicone gasket, it should fit tightly around the perimeter and have no cracks. If the gasket was damaged during opening, it is recommended to replace it with a new one or use a thin layer of silicone sealant to restore moisture protection, although this will make the device conditionally uncollectable.

⚠️ Warning: Before you finally install the lid, be sure to insert the batteries and check the device. If something is not working properly, it will be more difficult to disassemble it again due to the risk of damage to the reopened latches.

The final step is to install a soap tank and test it, and if it makes the same engine sound and it delivers a foam or liquid, it's a success, and if there's any extraneous noise or leaks, you'll have to repeat the disassembly, paying more attention to the tight fittings.

💡

Quality assembly depends on the correct stacking of plumes and the state of sealing rubber bands - they ensure the durability of the smart dispenser.

Frequently Asked Questions (FAQ)