How to set up cleaning rooms on the vacuum cleaner Xiaomi Vacuum Mop: from map to schedule

The Xiaomi Vacuum Mop (and its modifications: Pro, 2 Lite, P10, etc.) has long ceased to be just a casual cleaning device. With room zoning, it turns into a personal assistant that cleans only where you need to and when you want to. But many owners face problems: the robot does not see the room, confuses the zones or ignores the settings. In this article, step-by-step instructions are given the latest updates to the Mi Home app (2026), and hidden chips that are not written about in the official manuals.

We're going to go through the whole process, from creating an accurate map to adjusting your schedule by room, including solving typical errors, and also the zoning model compatibility table and the command list for voice assistants (Alice, Google Assistant), if you want a robot to clean the nursery every day, the living room every other day, and the bathroom only on weekends, this article is for you.

⚠️ Important: Room cleaning is only available for models with LDS-laser (e.g. Xiaomi Vacuum Mop 2 Pro) P10). Budget versions (e.g., budget versions, 1C or Lite) zoning works through virtual walls, but without being tied to rooms. Check your model in the table below.

1.Preparation: What you need to set up cleaning rooms

Before dividing your home into zones, make sure your Xiaomi Vacuum Mop is ready for it.

• 📱 Mi Home 6.5.0 and higher (update to Google Play or App Store).
• 🌐 Stable 2.4GHz Wi-Fi connection (5GHz not supported!).
• 🗺️ Ready-made map of the room (the robot must drive at least once throughout the house in cleaning mode).
• 🔋 Charge at least 50% – with a low charge, the robot may not save the card.

If the map is not already created, start a full cleaning (Settings → Map → Create a map) and wait for the robot to examine all the rooms. Do not interrupt the process, this can lead to holes in the map, which then have to be fixed manually.

⚠️ Note: If you have a two-storey house, you need a separate map for each floor. → Some models (e.g. Xiaomi Vacuum Mop) P10) Support up to 3 levels without resetting.

2. How to divide the map into rooms: a step-by-step algorithm

Once the map is ready, we start zoning, which takes 5-10 minutes, but it depends on the accuracy of the map how well the robot navigates.

1. Open the Mi Home app and select your vacuum cleaner.
2. Go to the Map section (the house icon in the bottom menu).
3. Click on the Edit icon (pencil in the upper right corner).
4. Select Add Room and circle the first zone boundaries with your finger, and the name is automatically assigned (e.g., "Room 1"), but it can be changed.
5. Repeat step 4 for all rooms. For corridors and small areas, use the option to combine (unless the robot recognizes them separately).

💡 Tip: If the robot has misdefined boundaries (for example, combined the kitchen and living room), use the function "Share the room.

All rooms are circled | Names are correctly indicated (e.g. "Bedroom" not "Room 3") |No overlapping zones | Corridors and passageways are marked as "Common Zone" (if necessary)

-->

⚠️ Warning: After editing the map, be sure to click Save (check in the top right corner). If you close the application without saving, all changes will disappear, and the robot will use the old version of the map.

3. Customization of cleaning by room: modes and schedule

Now that the rooms are marked, you can customize the cleaning schedule for each area, which is useful if:

• 🐕 There is a pet in one room, and you need to clean more often.
• 👶 The nursery requires daily wet cleaning.
• 🚪 There is a lot of dirt in the hallway, and dust in the bedroom.

How to set up:

1. In the Map section, click on the desired room.
2. Select Cleaning Settings → Mode: Standard Vacuum and Mop. Only vacuum cleaner for carpets. Only mop for hard floors. Deep cleaning for increased power (consumes more water and battery).

Set the suction level (from Quiet to Maximum) and the humidity level (if there is a wash function).

Click Save and go to the Schedule to set the days and times of cleaning.

🔹 Example of a schedule:

💡

If the robot is constantly confusing rooms, try adding virtual walls in the aisles. To do this, in the map editing mode, select Add a virtual wall and draw a line between the zones.

Zoning problems: why the robot can't see the room

Sometimes, after you've set up your room cleaning, the robot ignores the areas or cleans everything, and here are some common reasons and solutions.

• 🔄 Reset the map after the update. Once the firmware is in place, the robot can forget the zoning. Solution: re-circuit the rooms and save the map.
• 📶 Weak Wi-Fi signal. If the connection is interrupted, the robot loses access to the saved settings. Check the router or use the Wi-Fi amplifier.
• 🧹 Changes in the room. If you rearrange the furniture, the robot may not recognize the room. Run a second scan (Settings) → Map. → Update the map).
• 🔋 Low battery power. At below 20 percent, the robot returns to base and doesn't save any changes. Charge it to 100 percent before editing.

⚠️ Warning: If after all the manipulations the robot still can not see the room, try resetting the map settings (Settings) → Map. → Reset the map and recreate it. It's a last resort, but it works 90 percent of the time.

5. Voice control: commands for Alice and Google Assistant

If you have a smart speaker (Yandex Station, Google Nest) or a smartphone with a voice assistant, you can manage cleaning rooms without a phone. Here are the work teams for Xiaomi Vacuum Mop:

• 🎤 "Alice, start cleaning the living room on Xiaomi – the robot will clean only the specified room.

🔹 How to Connect Voice Control:

1. Choose the service: Yandex or Google Assistant.

⚠️ Warning: Voice commands only work for the rooms on the map, and if you say "clean up the bathroom" and that area is not in the settings, the robot will ignore the command or clean up the entire room.

6. Model compatibility: which Xiaomi Vacuum Mop supports room cleaning

Not all Xiaomi robot vacuum cleaners can divide a house into zones, and the table below shows the current models (2023-2026) and their capabilities:

💡 Tip: If your model does not support cleaning rooms, but there is LDS-Laser, try alternative firmware (like Valetudo) that reveals hidden features, but requires root access and disables cloud sync.

💡

Laser-free models (like 1C or Lite) can't divide a map into rooms, with virtual walls and cleaning areas at most, but without being tied to specific rooms.

7 Advanced settings: areas inside rooms and forbidden areas

The room cleaning function is just the beginning, and there are other useful tools in the Mi Home:

• 📍 Cleaning areas. You can select a section inside the room (for example, under the bed) and remove only it.
• 🚫 No-go zones: The robot will bypass the specified areas (useful for children's toys or power wires). → Add a no-go zone.
• 🔄 Cleaning sequence: The schedule can specify the order of the rooms (e.g. kitchen first, then corridor).
• 💧 Moisture control: Each room has its own water supply level (low to high) adjusted).

🔹 Example: In the bedroom, you can create two zones under the bed (2 times a week) and by the window (daily.

⚠️ Warning: If you use no-go zones, make sure they don't block the way to base, otherwise the robot may get stuck and discharge.

8. Frequent mistakes and how to avoid them

Even after setting it up properly, users are facing problems.-5 mistakes and their solutions:

1. Robot doesn't start cleaning on schedule. 🔹 Reason: Time is incorrectly specified or the robot is off. 🔹 Solution: Check the Settings → Schedule and make sure the vacuum cleaner is on base and connected to Wi-Fi.
2. Cleaning the wrong room. 🔹 Reason: The map is incorrectly bound. 🔹 Solution: Edit the map and save the changes.
3. Ignoring no-go zones. 🔹 Reason: Zones not saved or robot uses old map. 🔹 Solution: Reboot the robot (Settings) → Reboot) and check the relevance of the map.
4. Don't wash the floor in one of the rooms. 🔹 Reason: Low water level or improper regime. 🔹 Solution: Check the Settings → Humidity level and water tank.
5. Loses the card after the update. 🔹 Reason: Resetting settings when firmware. 🔹 Solution: Create a backup of the card (Settings) → Map. → Exports) before renewal.

💡 Lifehack: If the robot is constantly straying, try to install beacons (e.g., Xiaomi Mi Beacon) that help you pinpoint your location more accurately, especially in larger homes.

💡

Before any changes to your settings (update, reset, edit the map), check the battery power. At a level below 30%, the robot may not save data.

FAQ: Answers to popular questions