Modern cleaning gadgets require initial calibration, and the Xiaomi G1 is no exception. The process of initially integrating the device into the smart home ecosystem may seem complicated only at first glance, but if you follow the sequence of actions, it takes only a few minutes.
In this guide, we will take a closer look at each interface step, focusing on the nuances of wireless connectivity. Many users face difficulties in finding a device, and most often the problem lies in the router frequency range or regional account settings.
If you complete the procedure successfully, you can fully automate the cleanliness process, you can start cleaning remotely from the office, or you can get notifications that you have completed a cycle, and let's start preparing the hardware and software to get started with your new assistant.
Preparation for the first launch and charging
Before you try to link the device to a smartphone, you need to ensure its basic energy independence. Remove the Xiaomi G1 from the box and remove all transport films, including the protective elements on the side sensors and the bottom of the case. Pay special attention to charging contacts: they must be dry and clean to ensure the correct charge cycle.
Install the robot vacuum cleaner on the charging base and connect it to the power grid. The indicator on the top panel should light up, signaling the start of the process. Depending on the level of battery discharge in the warehouse, full charging can take from 3 to 5 hours. It is not recommended to interrupt this process or try to turn the device on before reaching a certain level of energy, as this can lead to incorrect operation of the power controller.
⚠️ Warning: Use only the original power supply supplied in the kit. Connecting to unstable voltage sources or using cheap analogues can damage the battery and disable electronics.
While the device is charging, prepare your mobile gadget. Make sure your smartphone is enabled with Bluetooth and geolocation (GPS) modules, which are essential for quickly detecting Xiaomi peripherals in the immediate vicinity. Also make sure your phone is connected to your home Wi-Fi network and you know the password for it.
Installation and registration in the Mi Home application
The control center for all Xiaomi equipment is the Mi Home app (also known as Xiaomi Home), which is available for iOS and Android operating systems. Download the current version of the program from the official App Store or Google Play. Older versions of the application may not support the new communication protocols used in the G1 model.
Once installed, launch the app and create a new account or log in to an existing one. Here is an important nuance: when registering, you need to choose the right region. If you are in Russia or CIS countries, the profile settings should select the “Russia” region or the corresponding country of your residence. Choosing the wrong region (for example, China or the United States) can hide compatible devices or limit the functionality of the server.
The registration process requires confirmation of your phone number or email address. Enter the code from the received SMS or profile activation letter. Once successfully logged in, the system may offer to update the basic profile data or agree to new terms of use of the service. This is a standard procedure for ensuring the security of your data and the correct operation of cloud storage.
The application interface may seem overloaded, but to set up the vacuum cleaner, we only need the home page and the device add menu. Make sure the app has permission to access the local network (for iOS this is critical) and geolocation. Without these permissions, automatic gadget search won't work, and you'll have to set everything up manually.
Connecting Xiaomi G1 to Wi-Fi Network
When the robot vacuum cleaner is charged and the app is ready to go, you can start pairing. Put the Xiaomi G1 next to your smartphone (no more than 1-2 meters away). Open the Mi Home app and click the + icon in the upper right corner to add a new device. The system will automatically start scanning available gadgets within Bluetooth range.
In the list of found devices should appear Xiaomi Robot Vacuum G1. If you find a device, click on it. If the automatic search didn't give you results, search by name at the top line or select the category "Vacilities" and find the model manually. After selecting the model, the application will request confirmation that the indicator on the device is flashing. If it is on or off, press and hold the buttons on the case (usually a combination of two buttons or one button during the course of the day). 3-5 seconds) until you hear a voice message about the pairing mode.
In the next step, select your home Wi-Fi network from the list and enter a password. It is critical to understand that most Xiaomi smart appliance models, including the G1, only support 2.4 GHz. If your router broadcasts a 5 GHz network or combines both bands into one SSID, connection errors may occur, in which case it is recommended to temporarily split the networks in the router settings or disable 5 GHz during setup.
☑️ Checking before connection
Once you enter the password, the data transfer process will begin. The progress bar will be displayed on the screen. At this point, the phone and the robot exchange encryption keys. Do not leave the application or lock the smartphone screen until the process is complete. Successful connection will be confirmed by the robot's voice message and the appearance of its card on the home screen of the application.
Setting up a room map and cleaning areas
Once successfully connected to the Internet, the robot is ready to build a map. Run a full cleaning through the app so that the Xiaomi G1 can travel around all available spaces. Laser rangefinder (LDS) located on the top tower of the device will scan the space, identify walls, furniture and obstacles.
Once you've cleaned, the app will form a detailed map of your apartment, you can save it, name it, and start editing it. The partitioning and merging of rooms allows you to adapt the digital model to the real layout, and this is necessary to create virtual walls and forbidden areas that the robot will not cross.
| Parameter of the map | Description of function | Recommendation for use |
|---|---|---|
| Virtual walls | Lines that the robot will not cross | Use at the thresholds or on animal bowls |
| No-go zones | Square areas to ignore | Close areas with wires or fringed carpets |
| Room separation | Dividing a single space into zones | Separate the kitchen and living room for selective cleaning |
| Keeping the map | Fixing the current configuration | Keep the map after each complete redevelopment. |
To fine-tune the areas, use Zoning, where you can select a specific area (like just a kitchen or an hallway) and send a robot to do intensive cleaning, saving battery life and time if the contamination is localized.
What do I do if the card is lost?
Management of working hours and timetables
The Mi Home app provides flexible tools for controlling the behavior of the Xiaomi G1. From the device settings menu, you can choose from one of the suction modes: Quiet, Standard, Turbo and Maximum. The choice of mode depends on the type of coating and the degree of contamination. Standard mode is enough for daily maintenance of cleanliness on the laminate, while for carpets with pile you will need maximum power.
One of the most useful features is to set up a schedule, so you can program the robot to start cleaning at certain times and on certain days of the week, for example, to set up a start at 10:00 in the morning when everyone has already left for work or school, which will ensure silence while you rest and a clean floor for your return.
- 📅 Timer: Set the exact start time for cleaning in 1 minute increments.
- 🔄 Repeat: Select the days of the week for automatic start-up (daily, weekdays, weekends).
- 🧹 Mode: Set your preferred suction power for automatic starts.
- 🗣 Voice: Customize the language and volume of the robot's voice notifications.
You can also update the firmware in this section, and from time to time, the manufacturer releases updates that improve the algorithms for building maps and correct errors, and it is recommended to regularly check for new versions of the software in the General Settings menu → Check for updates.
💡
For quiet cleaning at night (if the robot is not noisy), select Quiet mode and turn off voice notifications in the device settings.
Problem solving and maintenance
In the process of operation, there can be situations when the robot loses communication or stops responding to commands. Most often, the problem lies in an unstable Wi-Fi signal. If the robot has gone to a distant room where the signal is weak, it can disconnect from the server, in which case installing an additional repeater or moving the router will help.
Another common mistake is to "stick" the main wheel or brush. The app will give a notification with an error code. Turn the device over, clean the brush of the wound hair and check the free running of the wheels. Regular cleaning of filters and sensors prolongs the life of the device and maintains the suction power.
⚠️ Warning: Never wash the main one HEPA-water filter, unless specified otherwise in the specific modification instructions, wet filter swells and blocks airflow, which can burn the engine. Use only dry cleaning or replacement.
If the device is not responsive to the buttons and the application, you may need to completely reset the network settings, usually by pressing a certain combination of buttons on the case to the beep, and then the connection procedure will need to be reset, as in the first installation.
💡
Regular cleaning of sensors and wheels ensures that the robot will not get stuck and will be able to build accurate maps of the room for years.
Voice control and integration
The Xiaomi G1 supports integration with popular voice assistants. Through the Mi Home app, you can link your account to Yandex.Alice, Google Assistant or Amazon Alexa. This allows you to control voice cleaning without taking out your phone. Phrases like "Alice, turn on the vacuum cleaner" or "Ok Google, send the robot to base" work instantly.
To set up, go to the user profile in the app, select Other Platforms, and find the assistant you want. Follow the instructions on the authorization screen. Once connected, the device from the Mi Home app will appear in the corresponding voice assistant app.
Integration allows you to create complex smart home scenarios, such as a robot that can be triggered automatically when a smartwatch detects you're out of the house (geozone), or when a door-opener detects that everyone is gone, making a regular vacuum cleaner part of a fully-fledged smart home ecosystem.