Before the first inclusion: what you need to know about Xiaomi Vacuum Cleaner 1C
Xiaomi Mi Vacuum Cleaner Robot 1C — It is a budget model with laser navigation. LDS, It can build maps of space, save up to 5 floors and integrate into the Mi Home ecosystem, but even with a simple setup (base station, power adapter, spare room). HEPA-filter and brush) many users experience problems during the initial setup phase, and the main mistake is ignoring the preparation of the room before the first cleaning.
This model supports 3 suction modes (quiet, standard, turbo), zoned cleaning and virtual walls, but to activate them requires the correct binding to the Xiaomi account and firmware update. If you bought a used vacuum cleaner, be sure to reset to the factory settings through the button RESET on case (hold 5 seconds) – otherwise, previous card and schedule settings may conflict with your account.
Unlike the flagship models (for example, Xiaomi Robot Vacuum-Mop 2 Pro), the model is not designed for the first time. 1C There is no wet cleaning and camera feature, but it is lighter (3.5 kg) and quieter (up to 67 dB in turbo mode), making it ideal for small apartments with laminate or tiles, but requires special attention to adjusting the schedule - more about this in the section on automation.
Unpacking and preparation for the first launch
In the box with Xiaomi Vacuum Cleaner 1C you will find:
- 🤖 The robot vacuum cleaner itself with a side brush installed
- ⚡ Base station (charging dock) with power supply
- 🧹 Main floor brush (already inserted into the body)
- 🔄 Spare. HEPA-filter and sponge filter for the motor
- 📄 Brief instructions in 6 languages (without Russian)
Before the first inclusion, follow the mandatory steps:
- Put the dock on a flat surface against the wall, leaving 0.5 m of free space on the sides and 1.5 m in the front. Do not put the station under furniture or near heat sources - this will disrupt the IR sensors.
- Connect the power supply to the station and the socket. The indicator at the station should light up blue (charging) or green (full charge).
- Remove the transport film from the sensors (2 pcs. from the bottom of the case and 1 on the bumper).
- Make sure the side brush rotates freely - if it jams, clear the axis of the factory lubricant.
⚠️ Warning: If the indicator at the station flashes red, it means a power error. Check the voltage in the socket (must be 220V) ±10% and cable for damage, 20% of the time the problem is solved by replacing the power supply with the original one (article). MDZ-24-EU).
Connection to the Mi Home application: step-by-step instructions
To set up Xiaomi Vacuum Cleaner 1C You need the Mi Home app (version 6.5.4 or later) download it from the App Store or Google Play. Xiaomi account registration is mandatory - without it you can not save room maps and use the schedule.
Connection algorithm:
- Open Mi Home and press + → Add the device.
- Choose the category Smart home → Vacuum cleaners.
- In the list of models, find Mi Robot Vacuum-Mop (1C) (forget 1S or 2C!).
- Press Next and hold the Home and Spot buttons on the vacuum cleaner case for 3 seconds until you hear the beep.
- Connect your phone to a 2.4GHz Wi-Fi network (5GHz is not supported!) Enter the network password in the app.
- Wait until the sync is complete (up to 2 minutes), and the vacuum cleaner will appear in the list of devices.
If the error "Can not add device" occurs during the connection step, follow:
- 🔄 Restart router and vacuum cleaner (hold power button for 10 seconds).
- 📶 Check that the phone and vacuum cleaner are connected to the same Wi-Fi network (without the same Wi-Fi connection). VPN!).
- 📱 Update Mi Home to the latest version or reinstall the app.
- 🔌 Try another power supply for the docking station (power should be available) 24V/1.5And).
Make sure Wi-Fi is running at 2.4 GHz |
Shut down. VPN and firewalls on the phone|
Charge the vacuum cleaner to 50% (indicator green)|
Remove the transport film from the sensors|
Press the Home and Spot buttons at the same time-->
Setup of the first cleaning: modes and parameters
Once connected to Mi Home, the vacuum cleaner will automatically prompt you to create a map of the room.
- Place the robot at the docking station and click Start Cleaning in the app.
- Select Full Cleanup (not Zone or Spot!)
- Wait for the vacuum cleaner to go around all the rooms, and it'll take 15 to 40 minutes depending on the area.
- Once the cleaning is complete, the map will be saved automatically, and make sure that all rooms are marked correctly – divide or merge the zones manually if necessary.
Main cleaning modes in Xiaomi Vacuum Cleaner 1C:
| Regime. | Description | Working time (60 m2) | Noise level |
|---|---|---|---|
| Quiet | Minimum suction power (600 Pa) | 70-90 mine | 55 dB |
| Standard. | Optimal balance of power (1500 Pa) and time | 50-60 minutes. | 62 dB |
| turbo | Maximum power (2000 Pa) for carpets | 30-40 minutes. | 67 dB |
| Balance | Automatic power switching by type of coating | 45-55 mine | 58-65 dB |
For optimal operation, adjust additional parameters:
- 📍 Virtual Walls: In the App, click Map → Add → Virtual wall, useful for limiting areas with wires or fragile objects.
- 🔄 Repeated cleaning: activate in Settings → Additionally. → Repeated cleaning for better carpet cleaning (increases cleaning time by 30%).
- 🕒 Schedule: Set up automatic cleaning in the Schedule → Recommended time: 10:00 to 16:00 (less noise for neighbors).
💡
If the vacuum cleaner is constantly lost over a large area (more than 100 m2), break the map into several floors manually. → Save as a new floor after cleaning each area.
Integration with voice assistants and smart home
Xiaomi Vacuum Cleaner 1C Supports management through Alice (Yandex), Google Assistant and Amazon Alexa, but this requires pre-configuration in Mi Home.The main condition is that the vacuum cleaner and voice assistant must be tied to the same Xiaomi account.
Step-by-step integration with Alice:
- Open the Yandex app on your phone and go to Devices → Add the device.
- Choose Xiaomi from the list of brands and sign up with the same account as Mi Home.
- Allow access to the vacuum cleaner data (checks Management and Status).
- Wait until the synchronization (up to 5 minutes) and you can now use commands:
- "Alice, turn on the vacuum cleaner."
- "Alice, start cleaning the living room."
- "Alice, send the vacuum cleaner to base."Google Assistant has a similar algorithm, but in Mi Home settings you need to activate Google Home option in Profile. → Settings → Note: voice commands only work in English or Chinese in the original firmware. Russian requires localized firmware (e.g. Valetudo).
⚠️ Warning: If the vacuum cleaner does not respond to voice commands after integration, check: 🔗 Is your Xiaomi account linked to a voice assistant service (in profile settings). 🌐 Is the vacuum cleaner connected to the Internet (Wi-Fi indicator on the case should burn blue). 🔄 Is the vacuum cleaner firmware updated (current version at the time) 2026 year-end — 3.5.8_004026).
Solving common errors and fault codes
Xiaomi Vacuum Cleaner 1C It displays errors in Chinese and flashes the indicator, and below is the breakdown of the fault codes and how to fix them:
| Error code | Description | Reason. | Decision |
|---|---|---|---|
| 1 | Blocked sidebrush | Wrapped hair/threads or jamming | Clean the brush axis and check the fastening |
| 2 | The problem with the main brush | Clogging or wear of the brush | Remove the garbage, check the drive belt |
| 3 | The dust collector is clogged. | The container is full or the filter is full. | Clean the container and rinse. HEPA-filter |
| 5 | Collision sensor error | Pollution of IR sensors or bumpers | Wipe the sensors with alcohol, check the bumper for cracks |
| 9 | The problem with the laser rangefinder | Lens contamination LDS or mechanical damage | Clean the lens with a cotton swab, reload the vacuum cleaner |
If the vacuum cleaner does not return to the base, perform an algorithm check:
- Make sure the dock is connected to the outlet (the indicator is blue/green).
- Check if there are any obstacles on the way to the station (wires, thresholds above 2 cm).
- Update the room map manually: in the application click the Map → Update.
- Reset navigation settings: Settings → Additionally. → Resetting the card.
What to do if the vacuum cleaner does not turn on?
Optimization of work: tips for advanced users
To make the most of Xiaomi Vacuum Cleaner 1C, Take advantage of these hidden settings:
- 🔧 Do Not Disturb Mode: Activate in Settings → Schedule → Do not disturb the vacuum cleaner to start cleaning at a specified time (for example, at night).
- 📊 Cleaning statistics: in Settings → Cleaning history can be viewed with area, time and battery consumption for each session, which will help optimize the schedule.
- 🔄 Firmware Update: Check for Updates in Settings → Software Update: New versions improve navigation and add support for new commands for voice assistants.
- 🛠️ Custom firmware: Valetudo firmware is available for experienced users, which adds Russian, advanced maps and integration with Home Assistant. Installing custom firmware voids the warranty and requires disassembling the vacuum cleaner to connect to the home assistant. USB-port.
To increase the service life of the vacuum cleaner:
- 🧼 Clean the main brush and filters every 3 cleanings (use the brush from the kit).
- 🔋 Keep the vacuum cleaner on the base with a charge 40-60% (optimal for lithium-ion batteries).
- 🚫 Avoid cleaning wet surfaces – this leads to corrosion of sensors.
- 🔄 Once a month, calibrate the sensors: place the vacuum cleaner on a flat surface and hold the Spot button for 10 seconds.
💡
Regular cleaning of sensors LDS (Laser scanner increases navigation accuracy by 40%. Use dry microfiber - wet wipes can damage the lens.