Setup of the treadmill Xiaomi: from the Assembly to the first workout

Modern treadmills from Xiaomi and its sub-brands like the WalkingPad or Kingsmith are complex electronic devices that require a competent initial setup for safe operation. Many users make the mistake of starting intensive training immediately after unpacking, forgetting about the critical process of running and calibrating speed sensors. Proper tuning not only prolongs the life of the motor and the canvas, but also ensures accuracy of tracking your sports performance.

In this article, we will take a detailed look at the entire journey from installing the device in the right place to synchronizing with your smartphone through the Mi Home app. You will learn how to avoid common connection errors, why the track can slide sideways and how to set up automatic firmware updates to get new features.

Initial installation and launch preparation

The first step after unpacking is to choose the right place to install the simulator. Xiaomi produces both foldable models and stationary versions, but all require a certain amount of space for ventilation and safety.The minimum distance from walls and furniture should be at least 50 centimeters behind and sides to ensure free access to the emergency foot and prevent electronics from overheating.

Pay attention to the surface on which the track will be installed. The floor should be perfectly smooth, because even a slight skew can lead to uneven wear and the appearance of extraneous noise when the engine is running. If you plan to use the device on the carpet, put a rigid base or a special fitness mat under it, which will also reduce vibration.

⚠️ Warning: Do not connect the device to the power supply until all mounts are fully assembled and tested. Attempting to turn on an unfinished device may short-circuit or damage the controller.

It is also important to check the equipment before installing, the box usually contains the keys for adjustment, lubricant for the canvas, fuse and power cable. Make sure that the transport bolts, if any in your model, are removed, as they block cushioning and can damage the frame on the first start.

The process of running and lubricating the fabric

Factory lubrication applied to the deck is often unevenly distributed or partially dried during storage and transportation. The first full-fledged training requires a primary lubrication and run-in procedure, which will reduce friction between the cloth and deck, which is critical for engine durability.

Use only the manufacturer's recommended silicone lubricant, apply it in a thin layer under the canvas on either side, stepping about 5-10 cm from the edges. After applying, turn on the walkway in human walking mode at a speed of about 3-4 km / h for 2-3 minutes, which will help the oil evenly spread over the entire surface.

The running process also allows the canvas to sit down and stretch to a working state. In the first hours of operation, you may experience a slight smell of rubber or plastic, which is normal for new components. However, if the smell of burning persists after 30 minutes of operation, stop the device immediately and check the tension.

💡

Check the lubrication level every 100-150 km. If you feel that the steps have become more rigid or creaked, the lubrication procedure should be repeated.

Tightening and centering of the fabric

One of the most common problems owners face is to shift the treadmill to the side, and if you notice that the tape is moving left or right while driving, you need to do a mechanical adjustment, and you have a hexagonal bolt on the back of the track.

The adjustment process requires patience and precision. If the canvas moves to the right, it means that the right side is tighter than the left. You need to turn the right adjusting bolt counterclockwise (relax) half-rotate, and leave the left unchanged or tighten slightly. After each action, turn on the track at low speed and observe the behavior of the tape.

To test for the right tension, there is a simple test: lift the canvas in the middle. The gap between the tape and the deck should be about 3-5 centimeters. If the gap is larger, the tension is weak, if less, too strong, which puts extra stress on the engine.

⚠️ Warning: Never adjust the tension bolts on the engine running at high speed, this can lead to a sharp jerk of the cloth and injury to the hands, all manipulations are carried out at minimum speed or in a switched-off state, followed by a check.

Repeat the procedure until the canvas moves strictly in the center without shifting for a few minutes of operation. Remember that new tapes may require re-adjustment after the first 10-20 kilometers of run, as the material gradually stretches.

Connect to Mi Home and Zepp Life

Xiaomi’s modern smart home tracks are open only when connected to a smartphone, using either Mi Home (for Xiaomi’s ecosystem) or Zepp Life (formerly Mi Fit), depending on the device’s specific model. Download the software you need from the App Store or Google Play and register your account.

To pair, turn on the track and make sure your smartphone has Bluetooth and geolocation activated. In the app, click Add Device and select your model from the list or scan. QR-code located at the bottom of the platform or in the instructions. the connection process can take up to 30 seconds.

After successful pairing, it is recommended to immediately check for firmware updates. The track software is regularly updated, fixing bugs and adding new training modes. If the application offers to update firmware, be sure to agree and wait for the process to end without turning off the device.

In the app, you can set your goals: distance, time or number of calories burned, and you can also use an automatic exercise mode, where the speed will vary according to the program you choose, and synchronize data to track progress in dynamics and share achievements with friends.

Set up training modes and safety parameters

The track control interface may vary from model to model, but the basic principles remain the same: you can set the starting speed on the remote control or through the application, which will be activated when you start the movement. For models with automatic start this is especially important.

Pay special attention to the safety settings. Many models have a magnetic key or emergency stop system, make sure that when a key is disconnected or a user falls (in models with sensors), the track stops instantly, a critical parameter that cannot be ignored.

For advanced users, there are available gym mode or professional profiles where you can adjust the angle of inclination (if the model supports) and interval loads. The table below shows the recommended parameters for different types of users:

Remember that the settings in the app can be rewritten when you change your account. If the track is used by the whole family, create separate profiles for each family member so that statistics are not mixed and training recommendations are personalized.

💡

Personalization of profiles in the application allows the system to more accurately calculate calorie consumption and select the optimal training plan for each user.

Diagnostics of malfunctions and noise insulation

You may encounter various sound artifacts in the process, and it's normal to be able to honk a motor at high speeds, but a knock, a grind, or a rhythmic click indicates a problem, and most often, extraneous noise is caused by dust falling under the canvas or by uneven lubrication.

If the track is making a whistling sound, check the tension of the belt inside the body (partial disassembly is required, be careful). If you hear a rhythmic knock, a shaft may have deformed or a foreign object hit, in such cases it is better to contact the service center so as not to violate the warranty.

To reduce noise, especially if you live in an apartment, use anti-vibration mats, which not only protect flooring, but also extinguish impact loads, and also try not to put the track close to the walls so that the sound does not resonate.

⚠️ Warning: If you smell scorched rubber or see sparks, immediately pull the cord out of the socket. Continued use in this state will cause the device to catch fire or completely fail.

Cleaning the space under the canvas regularly with a vacuum cleaner (turned off!) helps prevent the buildup of pile, which is the main cause of overheating and noise.

Frequently Asked Questions (FAQ)

💡

To extend the life of the remote control battery (if wireless), remove the batteries if you do not plan to use the track for more than two weeks.