The transition from dry cleaning to full floor care requires understanding the specifics of your device. Modern Xiaomi models, such as the Mop, P1 or S10 series, are equipped with advanced water dosing systems, which turns them from simple dust collectors into full-fledged cleaning assistants. However, in order to be successful and not lead to damage to flooring, you need to strictly follow the sequence of actions during preparation and launch.
Unlike traditional floorwashing, where a person controls the pressing of a cloth, a robotic vacuum cleaner relies solely on software algorithms and the physical installation of modules. A mistake in the preparation stage can lead to the device simply distributing dirt around the house or, in the worst case, leaving puddles, which is why it is important to carefully study the design of your model before the first experiment with water.
In this article, we will discuss in detail the entire preparation cycle: from checking the compatibility of nozzles to fine-tuning the parameters in the Mi Home mobile application. You will learn how to correctly combine dry and wet cleaning, which modes to choose for different types of pollution and how to avoid typical beginner mistakes, which often reduce the efficiency of equipment to zero.
Compatibility check and module preparation
The first thing to start with is a visual inspection of the bottom of the device. Not all Xiaomi robot vacuum cleaners support wet cleaning out of the box. Basic models can only have a suction hole and a side brush. If your model is a Vacuum-Mop series or has the appropriate label in the name, then there must be a special removable tank module in the kit.
It's critical to make sure that the module is installed correctly. It has to snap with the characteristic sound and fit tightly to the body. If the module is skewed or not fully fixed, sensors can recognize this as an error and the device will refuse to start the process. Some advanced models, such as the Xiaomi Robot Vacuum X10+, use an electronic pump that requires more precise installation to properly operate the valves.
⚠️ Warning: Never try to pour water directly into the main dust container or onto the filter. HEPA. This will cause instant electronics to fail and loss of warranty.
Before filling with water, be sure to remove the module from the robot. Doing this on weight or, worse still, trying to open the tank lid while it is inside the device is extremely uncomfortable and fraught with spilling liquid on the contacts. Carefully pull the module by a special handle or notch located at the back or side, depending on the design of your Xiaomi.
Proper installation of water tank and napkins
The process of preparing the water module consists of several steps, each of which affects the quality of the final result. First, you need to open the water supply valve. On most models, it is located on the end of the tank and closed with a silicone plug. Open it only after the module is removed from the robot to avoid accidental leakage.
To fill, use only clean tap or filtered water at room temperature.Hot water can warp plastic parts and damage seals, and the use of chemical detergents is strictly prohibited by Xiaomi manufacturers.Aggressive chemistry destroys the pump's rubber gaskets and can clog the micro-holes of the drip feed system, leading to costly repairs.
Once the tank is filled, you need to install a microfiber wipe, which is attached to the bottom plastic platform of the module with Velcros, and it's important to spread the fabric so that there are no folds, otherwise the robot will leave unwashed stripes or, conversely, puddles in the places where the tissue is accumulated, and the tissue must fit tightly on the platform from all sides.
☑️ Readiness of the module
When the module is ready, it needs to be put back into the robot. Before you do that, make sure that the main dry garbage container is removed. Most Xiaomi models don't have the same vacuum and mop design. If you leave the dust container, the robot either won't close the top cover or the level sensor won't let the engine start.
Setting up parameters in the Mi Home app
Wet cleaning is managed exclusively through the Mi Home (or Xiaomi Home) mobile app. The interface may vary slightly depending on the server region, but the logic remains the same. After connecting the robot to Wi-Fi and adding it to the list of devices, go to the main control screen of your gadget.
At the bottom of the screen, you'll find a mode switch. To activate wet cleaning, you often just need to install a water module, and the robot automatically suggests the appropriate mode. However, to fine-tune the settings icon or select Cleanup Mode, where you will have water level control.
Three or four intensity levels are usually offered:
- 📉 Low – for easy daily cleanliness and sensitive coatings.
- 📈 Medium – the best option for mixed pollution and tiles.
- 📊 High - for severe contamination and persistent stains on ceramics.
- 🚫 Off – dry cleaning mode (requires the removal of the water module).
You can also activate Precise Cleaning or Double Cleaning in the settings menu if your model supports it, and in this mode, the robot will first vacuum the room, return to base, change the module (if there is a driver), or simply move on to the next step to thoroughly wipe the floor. This takes longer, but ensures maximum cleanliness.
What are virtual walls for wet cleaning?
Comparison of operating modes and surface types
The effectiveness of wet cleaning depends on the right choice of mode for a particular type of flooring. Incorrect adjustment can lead to swelling of the laminate or insufficient cleaning of the tiles. Understanding the physical processes that occur when a wipe comes into contact with the floor will help you customize the Xiaomi Vacuum Mop perfectly.
Below is a table that will help you navigate the best settings for different surfaces in your home:
| Type of coating | Recommended water level | Features of use |
|---|---|---|
| Laminate/Parket | Low. | Minimum moisture, rapid drying |
| Ceramic tile | Medium/High | It takes more moisture to dissolve the dirt. |
| Linoleum/Vinyl | Medium. | Universal mode, safe for seams |
| Natural stone | Low. | Avoiding chemistry and excess water in the seams |
Note that even with low water supply, some natural woods may require additional protection. The time it takes for a wipe to contact one point of the floor in High mode can be as long as a few seconds, which is equivalent to hand washing with a lot of pressure. So for expensive woods, it's best to test the robot in a discreet area beforehand.
If you have a combined coating in your home (like kitchen tile and living room laminate), use the mapping and room division function. You can set different cleaning options for each area in the app, for example, set high water levels for the kitchen and low water levels for the living room, and the robot will automatically switch modes when you move from room to room.
Starting the process and monitoring cleaning
Once you have set all the parameters, you can proceed to start. Press the Start button in the app or use a physical button on the device body. The robot will start building or refining the map if it is the first run, or immediately start cleaning on a known route. In wet cleaning mode, the trajectory may differ from the dry one: often uses a "Z-shaped" movement for more thorough washing.
When you're working, watch the display on the case or in the application. If the tank water level comes to an end, the smart vacuum cleaner will notify you with an audible signal and an in-app message. In some models, the water supply stops automatically, and the robot goes into dry cleaning mode to complete the mission, but you don't have to rely on it - it's better to add water.
⚠️ Warning: If the robot is stuck or lifted while working, be sure to wipe the wheel modules and sensors with a dry cloth before re-starting. moist dirt from the wheels can stain the clean floor.
The duration of the process depends on the area of the room and the chosen mode. At the maximum water intensity, the flow can be about 50-70 ml for 10-15 minutes of work. A standard tank of 150-200 ml is usually enough for 40-60 minutes of active work or for cleaning an apartment with an area of 60-80 square meters in mixed mode.
💡
To improve the efficiency of cleaning in the kitchen, where there are often fat pollution, first slightly walk through the problem areas with a wet wipe by hand. The robot perfectly removes dust and fine dirt, but he can not cope with old fat without chemicals, which can not be poured into the tank.
Post-completion services
The correct completion of the cleaning cycle is as important as the preparation. Once the robot has returned to base and reported completion, do not leave the water module inside the device. Residual moisture can condense and get to electronic components, especially if the room is high in humidity.
Remove the module, pour out the water and thoroughly rinse the tank. The microfiber wipe should be removed, washed in warm water without air conditioning (it reduces absorption), and dried. If you leave a wet cloth on the module, it will quickly multiply bacteria, and an unpleasant smell will appear, which will spread throughout the house the next time you clean.
Check your brush and wheels regularly, which can be used to wrap hair and wool, which when wet, can become a dense lump that makes it difficult to move, and it takes a couple of minutes to clean these elements, but significantly extends the life of your Xiaomi engine and chassis.
💡
The main secret of durability of the robot vacuum cleaner with the function of wet cleaning is the complete removal of the water module immediately after the end of work and thorough drying of all textile elements.