How to add a robot vacuum cleaner Xiaomi in Mi Home: full instructions with pictures and tips

Connecting Xiaomi’s robot vacuum cleaner to the Mi Home ecosystem is the first step to automating your home’s cleaning. Even if you’ve never worked with smart appliances before, adding the device will take no more than 10 minutes if properly prepared. However, many users face common mistakes: the device is not online, the app doesn’t see the vacuum cleaner, or it sends a message about a region incompatibility. In this article, we’ll look at all the steps of the connection, from unpacking the box to the first cleaning, and give tips for fixing common problems.

It is important to understand that the add-on algorithm may slightly differ depending on the vacuum cleaner model (e.g. Mi Robot Vacuum-Mop 2 Lite vs. Xiaomi Robot Vacuum-Mop P) and the Mi Home app version. We updated the instructions for 2026, taking into account the latest firmware and application interface updates. If your vacuum cleaner is released before 2020, check compatibility with the new Mi Home versions at the end of the article.

Before you start, make sure you have:

• Smartphone with installed application Mi Home (version no lower) 6.5.400 for Android/iOS)

• Sustainable Wi-Fi connection at 2.4 GHz (Xiaomi robots do not support 5 GHz)

Charged robot vacuum cleaner (minimum 20% battery)

Access to Xiaomi account (or willingness to create one)

1. Preparing the robot vacuum cleaner for connection

Before you add the device to the Mi Home, you need to physically prepare the vacuum cleaner. Start by unpacking the box and checking the equipment.

• 🔋 Robot vacuum cleaner with installed battery
• ⚡ Docking station for charging (some models integrated into the body)
• 📄 Instructions in several languages (including Russian)
• 🔌 Power adapter (if the docking station does not have a built-in unit)
• 🧹 Removable garbage container and filter HEPA

Put the vacuum cleaner in the dock and plug it into the socket. Don't turn on the power button, it should start automatically when you connect to the network. Wait for an audible signal (usually one short beep) to confirm that the vacuum cleaner is ready to adjust. If there's no sound, check:

• 🔌 Correct connection of the power cable to the docking station
• 🔋 Battery level (some models have an indicator on the body)
• 🔇 Loudness of sound on the vacuum cleaner (possibly switched off)

⚠️ Warning: If your vacuum cleaner has previously been connected to another Mi Home account, reset to factory settings. To do this, press and hold the Power and Home buttons (or Spot Clean, depending on the model) for 10 seconds until you hear a double beep.

Also make sure that the docking station is installed on a flat surface with a gap of at least 0.5 m from the walls and furniture, which is necessary for the navigation and charging system to work properly. If the vacuum cleaner cannot dock with the docking station after cleaning, the cause is often the wrong location of the base.

2. Installation and configuration of the Mi Home app

Mi Home is the central tool for managing all Xiaomi devices, including robot vacuum cleaners, and if it is not already installed on your smartphone, download it from official stores:

• 📱 Google Play for Android
• 🍎 App Store for iOS

After installation, follow the following steps:

1. Open the app and select the region of Russia (or Mainland China if you use the Chinese version of the vacuum cleaner).
2. Sign in with your existing Xiaomi account or create a new one (click Sign Up).
3. Confirm your email or phone number (you can use it to restore access).
4. Allow the application to access geodata and notifications (necessary for some functions to function).

If you already have an account, but you forgot your password, restore it through the Forgot password option?. Use the same account to which you plan to link the vacuum cleaner - reassigning the device to a different profile will require resetting the settings.

⚠️ Note: When choosing a region of China, some features (such as voice assistant Alice) may not be available. If your vacuum cleaner is purchased from an official Russian store, choose the region of Russia.

Once you've successfully logged in, you'll be on the app's home screen, and it shows all the devices you've connected to it. If you add a vacuum cleaner for the first time, the list will be blank, click on the icon. + in the upper right corner to start the connection process.

💡

Before adding the device, open your Wi-Fi settings on your smartphone and connect to a 2.4GHz network. Xiaomi robots do not work with 5GHz networks, even if your router supports both bands.

3.Increased addition of robot vacuum cleaner to Mi Home

Now, to the most important step, adding a vacuum cleaner to the app, follow the instructions below:

1. Start the connection process On the Mi Home Home screen, click + → Add the device. In the search box, type the name of your vacuum cleaner model (e.g. Mi Robot Vacuum-Mop 2 Pro) or select Cleaning category. → Robot vacuum cleaner.
2. The application will offer to connect to the 2.4 GHz network. Make sure that your smartphone is connected to the desired network (if the router has two networks with the same name, temporarily turn off 5 GHz in the router settings).
3. Scanner. QR-On the screen will be an instruction to scan QR-code that is on the bottom of the vacuum cleaner or on the docking station. If the smartphone camera does not recognize the code, enter it manually (click Enter the code manually).
4. Confirmation of connection After scanning, the vacuum cleaner will emit an audible signal and the indicator on the case will flash orange, which means that the device is ready to connect to Wi-Fi. Return to the application and wait for the process to complete (usually takes up a period of time). 30-60 seconds).

If you have a “Device Unconnected” error during the Wi-Fi connection phase, try the following solutions:

• 🔄 Restart router and vacuum cleaner (disconnect docking station from network for 10 seconds).
• 📶 Check that the smartphone and vacuum cleaner are on the same network (do not use mobile Internet).
• 🛡️ temporarily shut down the firewall or VPN smartphone.
• 📱 Update the Mi Home app to the latest version.

Once successfully connected, the vacuum cleaner will appear on the app's home screen, and you can now start setting up the cleaning options.

Smartphone connected to Wi-Fi 2.4 GHz |

Vacuum is at least 20% charged |

Dock station connected to socket|

QR-vacuum code is clean and readable|

The Mi Home app has selected the right region-->

4.Configure the cleaning parameters after connection

Successful addition of a vacuum cleaner to the Mi Home is only half the battle, so you need to customize the device to suit your needs. Open the vacuum cleaner card in the app and go to Settings (the gear icon in the upper right corner), and the following options are available here:

Pay special attention to the setting of cleaning areas.

1. Run the vacuum cleaner in Map mode (usually available in the Cleanup menu) → Map).
2. Wait for the robot to go around the room and build a map (may take up the space). 10-20 minute).
3. Divide the map into rooms by swiping your finger along the lines on the screen.
4. Assign names to rooms (such as the kitchen, bedroom) and save the changes.

If your vacuum cleaner supports moping (wet cleaning), an additional mop settings section will appear in the settings, where you can select the mop level (for example, Medium for laminate or High for tile) and the water change interval.

5. Common errors and their elimination

Even with the correct following of the instructions, users sometimes face problems. TOP-5 errors and ways of solving them:

• 🔴 "Offline Device" Reason: The vacuum cleaner has disconnected from Wi-Fi or is out of charge. Solution: Check battery power (minimum 20%). If there is a problem on the network, restart the router and reconnect the vacuum cleaner to Settings → Wi-Fi.
• 🔴 "Failed to add device" Reason: Region incompatibility in Mi Home or outdated vacuum cleaner firmware.Solution: Update firmware through Settings → If the error repeats, change region to China (Chinese version only).
• 🔴 The vacuum cleaner doesn't build a map. The reason is: Too dark or no landmarks (like furniture) Solution: Turn on the light in the room and remove small objects from the floor. Start mapping again.
• 🔴 "Error 10" or "Error 12" Cause: Sensor problems or brush jamming. Solution: Turn over the vacuum cleaner and clear the main brush and side brushes of hair/garbage. Check the sensors for dirt.
• 🔴 Vacuum doesn't return to base Reason: Dock station is in hard-to-reach area or battery is dead Solution: Move dock to open space. If battery is dead, plug vacuum cleaner to manually charge.

If none of these methods worked, try a full reset.

1. Turn the vacuum cleaner off the grid.
2. Press and hold the power button for 15 seconds until you hear the beep.
3. Reconnect the device as you did on the first start.

⚠️ Warning: Resetting will delete all stored maps, schedules and cleaning settings. After resetting, the vacuum cleaner will have to be added to Mi Home again.

To diagnose complex problems, use the in-app error log (Settings) → Logs: This displays the latest crash codes and their description in English, and can be found in official Xiaomi documentation or forums (e.g., in the official Xiaomi documentation, 4PDA).

💡

If the vacuum cleaner is not connected to Wi-Fi, first check the router settings: turn off the Smart Connect function (combining 2.4 and 5 GHz into a single network) and make sure that there are no Cyrillic symbols in the network name.

6. Compatibility of Xiaomi robot vacuum cleaners models with Mi Home

Not all Xiaomi robot vacuum cleaners work equally well with the latest Mi Home versions. Below is a table of compatibility of popular models:

If your model is not supported by the latest Mi Home, try the following solutions:

• 📥 Install an older version of the app (e.g. 6.1.100 for Android can be found on APKPure).
• 🔄 Update the vacuum cleaner firmware manually through Mi Home → Settings of the device → Update of the PO.
• 🌐 Use alternative applications such as Home Assistant or IoT Mi Control (requires customization skills).

Models released before 2020 (such as Mi Robot Vacuum 1) may require firmware through the ADB. This process is more complicated and requires connecting the vacuum cleaner to your computer. Instructions for firmware can be found on profile forums, but we recommend contacting the service center if you are not sure about your skills.

7. Additional Features: Integration with a Smart Home

Xiaomi’s robot vacuum cleaner could become part of the smart home ecosystem by interacting with other devices.

• 🏠 With Mi Home Automation, set up a rule: if all family members leave the house (by geolocation of smartphones), the vacuum cleaner begins cleaning.
• 🔦 Scheduled cleaning with lighting in mind Connect the light sensor Xiaomi and program the vacuum cleaner to clean when the room becomes dark (for example, in the evening).
• 🚪 Stop cleaning when opening the door If you have a door opening sensor, set up a vacuum cleaner stop when someone enters the room.
• 🗣️ Voice control through Alice/Google Say, “Alice, start cleaning the kitchen” and the vacuum cleaner will start working in the specified area.

To set up automation:

1. Open Mi Home and go to Automation (two-arrow icon).
2. Press Create. → Add a condition and select a trigger (e.g., geolocation or schedule).
3. Add the action – Start cleaning or Stop cleaning.
4. Save the script and activate it.

For voice control, connect your Xiaomi account to Yandex.Station or Google Home:

1. In the Yandex app, go to Devices → Add Device → Xiaomi.
2. Log in and allow access to smart devices.
3. After synchronization, the vacuum cleaner will appear in the list of managed devices.

⚠️ Warning: For voice control, the vacuum cleaner must be linked to a Xiaomi account with a region in Russia. If you used China when setting up, voice commands will not work.

If you use Home Assistant, integration with Xiaomi vacuum cleaner is done through a component vacuum.xiaomi_miio. This will require a device token that can be obtained using the miio-cli utility or online services (for example, MiHome Dev).

8. Updating firmware and optimizing work

Regularly updating the vacuum cleaner firmware improves its performance, adds new features and corrects errors to check for updates:

1. Open Mi Home and select your vacuum cleaner.
2. Go to Settings. → Update of the PO.
3. If a new version is available, click Update and wait for the process to complete (don’t disconnect the vacuum cleaner from the network!).

In some cases, the update may freeze or interrupt.

• 🔄 Reboot the vacuum cleaner (disconnect the docking station from the network for 30 seconds).
• 📶 Check the stability of Wi-Fi (signal should not be weaker) -60 dB).
• 📴 If the update is interrupted, try to re-start it in 10 minutes.

To optimize the operation of the vacuum cleaner, follow these tips:

• 🧹 Clean the main brush and side brushes after each cleaning (especially if there are animals in the house).
• 🔋 Calibrate the battery once every 3 months: completely discharge the vacuum cleaner, then charge to 100% without interruption.
• 🗺️ Periodically update the map of the room (manual or automatically).
• 🌡️ Keep the vacuum cleaner in a dry place at a temperature 10-35°C.

If the vacuum cleaner began to suck worse or discharge quickly, check:

• 🔋 Battery status (C Settings) → The state of the device is displayed by the level of wear).
• 🧲 Clean filter HEPA (Wash it under running water once a month).
• 🌀 Integrity of brushes (replace with original spare parts when worn out).

Xiaomi robot vacuum cleaner parts can be ordered from an official store or on sites like AliExpress. When buying, check compatibility with your model - for example, brushes for Mi Robot Vacuum-Mop 2 Lite will not be suitable for Xiaomi Robot Vacuum-Mop P.

💡

Update your vacuum cleaner firmware at least once every 3 months.Newer versions often contain critical fixes for navigation and safety.

FAQ: Answers to Frequent Questions