Keeping your home clean with modern technology requires regular maintenance of the device itself. Many smart gadget owners forget that a robot vacuum cleaner needs care as much as a regular household appliance. Ignoring hygiene can lead to poor cleaning quality, unpleasant smells, and even breakdown of expensive equipment.
Timely cleaning of filters and brushes ensures that your Xiaomi Robot Vacuum will work with maximum efficiency. In this article, we will discuss a step-by-step algorithm that will help to extend the life of your assistant. You will learn about the intricacies of maintenance of detergent modules, which are often not mentioned in standard manuals.
Preparation for maintenance of the device
Before any manipulations are initiated, it is necessary to completely disconnect the device from the charging station and turn it off programmatically.This is a critical step for safety, since accidental start of the motor during cleaning can lead to injury to the fingers or damage to the mechanisms. It is recommended to turn the robot vacuum cleaner upside down, laying a soft towel or mat so as not to scratch the body.
Visually inspect the case for visible dirt, dust in hard-to-reach areas and animal fur residues. If you use a wet-cleaning model, make sure the water tanks are empty. The accumulated water can spill into the case when disassembled, leading to oxidation of the contacts.
To work, you'll need a set of simple tools that you usually have in every home. Don't use aggressive chemistry or abrasive sponges that can damage plastic.
- 🧹 Soft dry brush to remove dust from sensors.
- ✂️ Scissors or a special knife to remove wound hair.
- 💧 Distilled water for washing filters and tanks.
- 🧽 Microfiber for cleaning external surfaces.
⚠️ Warning: It is strictly forbidden to wash the main body of the robot under the tap or immerse it in water. Internal electronics are not moisture-protected, and ingress of moisture will lead to irreversible damage.
Maintenance of the main brush and side brooms
The central brush is the heart of the dry cleaning system, collecting most of the garbage. Over time, hair, thread and wool are wound onto the surface, which puts additional stress on the engine. Regular cleaning of the V-shaped brush (or standard one depending on the model) prevents the engine from overheating and reduces noise levels during operation.
To remove the brush, you need to press the locks on the sides of the protective cover and remove it. Carefully pull the brush at one end, freeing the second from the groove. Use scissors to cut the tightly wound fibers, and then remove them manually. Don't pull too hard to damage the bearings.
☑️ Checking brushes
Side blizzards also require attention, especially if they have a pile that gets dust clogged in, can be gently unfastened and washed under warm water, but before being re-installed, they must dry completely. A wet blizzard will scatter dirt rather than collect it.
The secret of perfect brush cleanliness
Cleaning of the filtration system and dust collector
The filtering system in Xiaomi devices usually consists of a primary filter-grid and a main filter. HEPA-It's the condition of the filter that determines how clean the air is when it leaves the device, and the clogged filter dramatically reduces the suction force, which causes the robot to pick up garbage worse and stop more often with an error.
HEPA-filters should not be washed with water in normal mode unless the instructions for a particular model indicate otherwise. Most often they are only recommended to be knocked out with a light tap on the trash can. If the filter is gray and cannot be cleaned, it should be replaced with a new one.
The dust collector (the garbage container) should be emptied after every 2-3 cleanings. The container often accumulates fine dust in corners that are difficult to shake out. Wash the container with water, but make sure it is completely dry before being placed back into the robot.
| Element | Frequency of cleaning | Cleaning method | Can I wet you? |
|---|---|---|---|
| Dust collector | Every 2-3 cleanings | Water-rinsing | Yeah (no filters) |
| HEPA-filter | Once every 2 weeks | Dust-knocking | No (usually) |
| The main brush | Once a week. | Hair removal | No. |
| Sensors. | Once a month | Dry napkin. | No. |
Care for the detergent module and tanks
Motoring models should pay special attention to water tanks, and unlike dry containers, they create a moist environment that is ideal for bacteria to multiply and mold to appear, and after each cleaning, the remaining water from the tank must be drained.
Rinse the tank with clean water at least once a week. If you've used floor cleaners, flushing is a must, because the chemistry can clog the micropomp or leave a sticky plaque. Pay attention to the outlet of the water, which can pass through small debris.
💡
Use only distilled or filtered water for the detergent module. Hard tap water contains salts that eventually form scale inside the pumps and tubes, disabling them.
A floor rag (cloth wipe) requires washing after each use. The accumulated dirt in the fabric will simply be smeared on the floor when reused, degrading the cleaning quality. Some Xiaomi models support automatic base cleaning, but manual washing is still necessary.
⚠️ Warning: Never leave water in the tank unless you plan to use a robot in the next few days.Stagnant water acquires an unpleasant odor that can spread throughout the house while working.
Diagnostics and cleaning of sensors and wheels
The navigation of the robot vacuum cleaner depends on the accuracy of the readings of various sensors. The fall sensors (located around the perimeter of the bumper) and the collision sensors must always be clean. Dust on the sensor lenses can cause a false alarm, which will cause the robot to "fear" falls or not see obstacles.
Wheels are another element that is often ignored: there is a dense mass of dust and hair between the wheel and the body, which blocks rotation. If the robot starts making strange sounds or getting stuck in a flat place, check the wheels. They can be cleaned carefully with a cotton swab dipped in alcohol.
Charging contacts on the bottom of the case and at the docking station also need periodic wipes. The oxidation of the contacts leads to poor charge, and the robot may not recharge to 100%, which reduces its battery life.
💡
Clean sensors are the key to a proper map of the room, and dirty sensors cause the robot to make wrong routes, skip sections, or rush around the room randomly.
Typical errors and prevention of breakdowns
One of the most common mistakes is the use of aggressive cleaning products, such as chlorine solutions or vinegar in high concentrations, which destroy rubber seals and plastic parts of the structure, and it is better to use specialized products or a weak soap solution for disinfection.
And users often forget to change their consumables, and filters and brushes have limited resources, even with perfect cleaning. HEPA-The filter loses its properties through 3-6 Ignoring replacement causes the motor to overload, trying to pump air through a clogged filter.
Regular maintenance takes no more than 10-15 minutes a week, but saves thousands of rubles on repairs. Following the simple rules of hygiene of the device will ensure its stable operation for many years.