Connecting Xiaomi Mi Smart Kettle Pro to Alice: Full instruction with problem solving

The Xiaomi Mi Smart Kettle Pro is not just a water boiler, but a full-fledged element of the smart home ecosystem that can be controlled by voice through Alice. However, many users face difficulties in the first setup: the kettle does not appear in the list of devices, Alice does not see it, or voice commands work incorrectly. In this article, we will analyze the step-by-step connection algorithm taking into account all the nuances from equipment preparation to solving typical errors.

Controlling the water temperature with your voice, running a boil on a schedule, or remotely turning on the kettle via your smartphone is all possible after the right integration. But to make it work, you not only need to synchronize the devices, but also set up the region in Mi Home, check the compatibility of the firmware, and link the accounts of Xiaomi and Yandex. If you have already tried to connect and you have an error like "Device is not supported" or "Can not found the kettle", do not rush it back to the store, most likely the problem lies in the small things.

In this instruction, we will consider:

• 🔌 Equipment requirements and preliminary training;
• 📱 Step-by-step connection via Mi Home and Yandex;
• 🗣️ Set up voice commands for Alice;
• ⚠️ Common mistakes and ways to eliminate them.

1. Preparation for connection: what will be needed

Before you start setting up, make sure you have everything you need. Without some components, syncing the Mi Smart Kettle Pro with Alice will not be possible.

Here's the mandatory set:

• 📱 Smartphone on Android (version 6.0 and above) or iOS (version 12.0 and above) with installed applications Mi Home and Yandex;
• 🔌 Smart kettle Xiaomi Mi Smart Kettle Pro (model) DJC01CM or DJC02CM);
• 📶 Stable Wi-Fi connection at 2.4 GHz (kettle does not support 5 GHz!);
• 🔋 Charged base of the kettle (the indicator should burn green or blue).

Pay special attention to the version of the kettle firmware, if it is outdated, Alice may not recognize the device. → Settings → Firmware Update: Minimum supported version for working with Alice — 1.4.5_0039.

⚠️ Note: If your router only works in the 5GHz band, the kettle will not be able to connect to the network, in which case you will have to temporarily switch the router to 2.4GHz mode or use a separate access point.

2. Installation and configuration of the Mi Home app

Mi Home is a bridge between the teapot and Alice, and synchronization is impossible without it.

• 🤖 Google Play for Android;
• 🍎 App Store for iOS.

After installation, follow the following steps:

1. Start Mi Home and sign up (or sign in to an existing Xiaomi account)
2. Select the "Russia" region (this is critical for Alice compatibility!)
3. Press "+" in the upper right corner and select Add device;
4. In the list of categories, find the Kitchen →
5. Follow the instructions on the screen: turn on the kettle, holding the power button for 3 seconds until the indicator blinks.

If the kettle is not detected, try:

• 🔄 Reboot router and kettle;
• 📵 Shut down. VPN or proxy on a smartphone;
• 📡 Bring the kettle closer to the router (maximum 5 meters).

The Mi Home app is installed|Xiaomi account registered|Region in Mi Home - Russia|The kettle is on and flashes blue.|Smartphone connected to Wi-Fi 2.4 GHz-->

3. Synchronization with Alice via Yandex

After the successful addition of the kettle to Mi Home, you need to link it to Alice.

1. Open the Yandex application on your smartphone;
2. Go to the Devices section → Add the device;
3. Choose Xiaomi from the list of brands;
4. Enter the username and password from your Xiaomi account (the same as in Mi Home);
5. Allow access to devices by clicking Confirm.

If the kettle does not appear in the list of Yandex devices, check:

Important: after linking accounts, it can take up to 10 minutes until the kettle appears in the list of Alice devices. If it is not available after 15 minutes, untie and reconnect your Xiaomi account in the Yandex settings.

💡

If Alice persists in not seeing the kettle, try temporarily disabling two-factor authentication in Xiaomi's account while setting up.

4.Tune voice commands for the kettle

Now that the kettle is plugged in, you can set up voice control, and Alice supports the following basic commands:

• 🔥 «Alice, turn on the kettle" - start the boiling;
• 🌡️ «Alice, heat the water to 80 degrees - setting the temperature;
• ⏱️ «Alice, turn on the kettle in 10 minutes – delayed start;
• ❓ «Alice, what is the temperature of the water in the kettle? – status request.

To ensure that the teams work correctly:

1. Open the Yandex application;
2. Go to the Devices. → [Your kettle] → Settings;
3. Make sure the voice control option is enabled.
4. If necessary, rename the kettle (such as “Kitchen kettle”) to make Alice better at recognizing it.

If Alice says, “I don’t know how to do it,” then:

• 🔄 Xiaomi Skills Not Updated (Check Settings) → Skills);
• 📛 The name of the kettle contains special symbols or Cyrillic (use only Latin and numerals);
• 🌐 Region in Mi Home is lost to China (replace to Russia).

5. Common mistakes and their solutions

Even with the right setup, users often face problems. TOP-5 errors and ways of correcting them:

1. The teapot is connected to Mi Home, but not visible in Yandex 🔹 Reason: Outdated firmware or incorrect region. 🔹 Solution: Update the kettleware and check the region in Mi Home (should be Russia»).
2. Alice says, "The device is not responding» 🔹 Reason: The teapot is disconnected from Wi-Fi or the base is discharged. 🔹 Solution: Reset the kettle (hold the 10 sec button) and check the connection indicator.
3. Voice commands work once in a while. 🔹 Reason: Weak Wi-Fi signal or conflict with other devices. 🔹 Solution: Connect the kettle to another 2.4GHz channel in router settings.

⚠️ Note: If after all the manipulations, the kettle never appeared in Alice, check if it is linked to another Xiaomi account. → Devices → Shared devices and remove the kettle from there if there is one.

Additional features: schedules and automation

With the Mi Smart Kettle Pro, you can set up automatic scripts that save time.

• ☕ Morning coffee: The kettle turns on at 7:00 and heats the water to 90°C;
• 🏠 No-Home mode: The teapot shuts down if everyone leaves the apartment (by geolocation);
• 🌙 Night mode: Water temperature drops to 60°C after 22:00.

To create a script:

1. In Mi Home go to Automation → Create → If...
2. Select a condition (time, location, voice command)
3. Add action: Control kettle → Turn on / off / Set the temperature;
4. Save the script.

To sync with Alice, these scenarios must be cloud-based (not local).

💡

Alice's voice commands only work when the Internet is active, and if the Wi-Fi goes off, the kettle will only be managed via Mi Home on the local network.

7. Update firmware and reset settings

If the kettle is unstable, first of all update the firmware:

1. Open Mi Home;
2. Select the kettle → Settings → Update the firmware;
3. If a new version is available, click Update.

If the update has hung or the kettle has stopped responding, reset to factory settings:

1. Turn off the kettle from the net;
2. Hold the power button for 15 seconds until the indicator starts to flash quickly.
3. Reconnect the kettle and reset the setting.

⚠️ Warning: Reset will delete all stored temperature and schedule settings, and then you have to reconnect the kettle to Mi Home and Alice.

FAQ: Frequent questions about connectivity