Xiaomi’s modern Smart TVs provide access to a huge amount of content, but without an Internet connection, their functionality is severely limited. Owners often face a situation where after buying or resetting the device can not see the network or connect to it, this is a common problem that is solved by the correct algorithm of actions in the system menu.
Before you start complex manipulations, you need to make sure that the router is working correctly and gives a signal. In most cases, it is enough to find the desired item in the menu, but sometimes you need to manually configure the router. IP-address DNS. It is important to understand that the interface may vary slightly depending on the version of the Android operating system. TV or PatchWall.
In this article, we will take a look at all the steps of connection, from basic settings to solving specific errors. DNS-What to do if the wireless module is no longer responding to system commands. Follow the instructions consistently to avoid errors.
Basic setting of wireless connection
The first step is always to log in to the main settings menu. On the remote, find a button with a gear or icon of the house to go to the PatchWall interface. In the upper right corner of the screen, there is usually a settings icon that you need to select to go to the system menu.
Once you log in, find the network connection section, depending on the firmware version, it can be called the Web and the Internet, or just the Web, and that's where all the switches and lists of access points are.
Activate the Wi-Fi slider, turning it into "On." The TV will start scanning the airwaves and in a few seconds display a list of available networks. Find your router's name (SSID) in the list and click on it to enter your password.
- 📶 Make sure that the TV is in the zone of confident reception of the router signal.
- 🔑 Check the keyboard layout when entering the password to avoid errors.
- 🔄 If the network is not found, try updating the list by pressing the corresponding button on the screen.
⚠️ Note: When entering a password, pay attention to the letter register. Android is sensitive to upper and lowercase characters, as well as special signs.
After successful data entry, the TV will try to get IP-If the connection is established, the Connected status will appear next to the network name, and the signal level icon will appear in the status bar.
Problems with 2.4 GHz and 5 GHz frequencies
One of the most common reasons why Xiaomi Mi TVs don’t see the network is the discrepancy in frequency bands.Most budget TV models only support the 2.4GHz standard, while modern routers often only distribute the network at 5GHz or combine them under one name.
If your router is broadcasting the network 5 GHz, and the TV doesn't support it, you just don't see your hotspot on the list, so the solution is to log in to the router's settings and split the networks into two different names, like HomeWiFi and the Internet. HomeWiFi_5G.
Some channels in the 2.4 GHz range (especially 12-14) may not be supported by TV modules released for certain regions. In the router settings, it is recommended to set a static channel, for example, 1, 6 or 11, and a channel width of 20 MHz for maximum compatibility.
How to check the supported TV frequencies?
Sometimes, changing the region in the router settings helps, so if you put a region in the U.S. or Europe, the list of available channels and their characteristics can change, allowing the TV to see the network.
Manually configuring IP and DNS addresses
If you automatically receive addresses through the protocol DHCP It doesn't work, you have to manually configure it, and it often happens when you overload a router's network or you have a conflict. IP-addresses within the local network.
In the network selection menu, instead of connecting quickly, select "Additional" or "Extended settings." IP-Connections from "Automatic" to "Manual" (Static).
You will need to enter the following parameters:
- 🌐 IP-address: unique address in your subnet (for example, if the router 192.168.1.1, then give the TV 192.168.1.55).
- 🚪 Gateway: IP-router.
- 🔢 Network prefix: usually 24.
- 📡 DNS 1 and DNS 2: Domain Name Server Addresses.
Special attention should be paid DNS. Often, providers block or slowly process requests through their servers. DNS Google or Cloudflare could speed up smart features.
DNS 1: 8.8.8.8
DNS 2: 8.4.4.8After you have entered all the data, save the settings and try to connect again. If the error persists, try alternative DNSs, such as 1.1.1.1.
☑️ Checklist manual adjustment
Comparison of connection methods
There are several ways to connect your TV to the Internet, and each has its own characteristics, depending on your specific situation: signal stability, cable availability, and software version.
Below is a table comparing the main connectivity options for Xiaomi devices:
| Method | Stability | Speed. | Difficulty |
|---|---|---|---|
| Wi-Fi 2.4 GHz | Medium | Up to 50 Mbps | Low. |
| Wi-Fi 5 GHz | Tall. | Up to 300 Mbps | Medium |
| LAN cable | Maximum | Up to 1000 Mbps | Low. |
| Wi-Fi adapter | Depends on the adapter. | Depends on the adapter. | Tall. |
Using a wired LAN connection is always preferable for watching high-resolution 4K video, as it eliminates interference and loss of data packets.
If the cable is not possible, try to place the router in line of sight from the TV or use Wi-Fi repeaters to amplify the signal.
Resetting network settings and software updates
When a software failure interferes with the connection, the effective solution is to reset the network settings, which will return the network settings to factory values without affecting personal files or installed applications.
To do this, go to Settings → Device → About → Reset. In some versions of the interface, the network reset option is located directly in the Wi-Fi menu under the “Forget Network” or “Delete Network” button.
It is also critical to keep firmware up to date. Xiaomi developers regularly release updates containing driver fixes for wireless modules.
⚠️ Before updating your firmware, make sure you have a stable network connection, otherwise the TV may turn into a brick».
Check for updates in the About System → System Update menu. If the automatic search does not find new versions, the firmware file can be downloaded from the official website to the USB flash drive and installed manually.
💡
Before resetting the settings, write down the current IP-address and parameters DNS, Restore access to local resources quickly if necessary.
Solving specific connection errors
Sometimes users are faced with a message “failed to receive” IP-Address" or an endless "Connect..." cycle, which may indicate a problem with encryption or signal power.
Try changing the type of security on the router. WPA2/WPA3, The TV may not work properly with it. WPA2-PSK (AES).
Another reason could be a crowded DHCP table on the router.Rebooting the router will clear the table of leased addresses and allow the TV to get a new IP.
- 🔌 Turn off the TV from the socket on 1-2 minutes to completely reset the module.
- 📡 Reduce the distance between the router and the TV for the test.
- ⚙️ Turn off the function. MAC-Filtering on the router if it is activated.
In rare cases, change helps. MAC-TV addresses (cloning) MAC), if the provider blocks unknown devices, but for home networks it is extremely rare.
💡
90% of Wi-Fi problems on Xiaomi TV are solved by splitting the router frequencies or changing DNS-servers.