Xiaomi 8 Pro (codenamed MI 8 Pro) is still a hot device thanks to its powerful hardware and MIUI support. One of the most popular features is the ability to distribute mobile Internet to other gadgets. This saves you when traveling, in the country or when the main Wi-Fi suddenly went off. However, many users face problems: the access point does not turn on, devices do not connect, or the Internet “slows down”.
In this article, you can find step-by-step instructions for all ways to distribute the Internet on Xiaomi 8 Pro (including hidden settings). MIUI), This is a table comparing methods for speed and power consumption, and solving the 5 most common errors. MIUI 12-14 and Android 9-11 (depending on your device’s software version).
If you have previously tried to set up an access point and encountered difficulties, check the section “Typical problems” where you can see cases when the smartphone is not visible in the list of networks, the connection is terminated after 5 minutes or traffic is limited to the operator.
1. Method. №1: Distributing Wi-Fi via Modem Modem (fastest)
This is a standard method that works on all Xiaomi smartphones: It allows you to connect up to 8 devices at a time (laptop, tablet, other phone) and provides top speeds of up to 150 Mbps at 2.4 GHz or 433 Mbps at 5 GHz (if supported by your device).
How to turn on:
- Open Settings → Network and Internet → Access Point and modem.
- Slip on the Wi-Fi Access Point.
- Activate the Wi-Fi Access Point slider (at the top of the screen).
- Set up network settings (if necessary): 🔄 Name of the network (SSID): Think of a unique name (for example, Mi8Pro_Hotspot). 🔐 Password: minimum 8 Symbols, it is better to use letters, numbers and signs (!@#$%). 📶 Range: Choose 5 GHz for faster speed (if your devices support your device).
Once activated, a notification will appear on the screen, Access Point is active, and other devices can now connect to your network by entering a password.
The device has mobile Internet enabled | Network signal level not lower than 2-3 divisions | VPN | Password entered without errors (registration is important!)
-->
⚠️ Note: Some operators (e.g. MTS or Beeline) block the Internet distribution by default. If the Internet does not work after connecting devices, see section 5 (“Error: Connected, but no Internet»).
2. Method. №2: Distribution via Bluetooth (savings charge)
This method consumes 30-40% less battery than Wi-Fi, but the speed is limited to 3-5 Mbps (enough for instant messengers and mail, but not for HD video), suitable if you need to connect only one device (for example, a laptop or tablet) and save the battery of your smartphone.
Instructions:
- Turn on Bluetooth on both devices.
- On Xiaomi 8 Pro, go to Settings → Connection Devices → Bluetooth.
- Select the device from the list and confirm the pairing.
- After connecting, go back to Settings → Network and Internet → Access Point and modem.
- Activate the Modem slider via Bluetooth.
On a connected device (such as a laptop) in the network settings, select Connection via Bluetooth and specify your Xiaomi 8 Pro.
💡
If the Bluetooth connection is constantly broken, try turning off the Bluetooth power saving mode on your smartphone in Settings → Battery → Energy saving applications.
3. Method. №3: Distribution through USB (maximum stability)
Connection to USB-The cable provides the most stable speed (up to 300 Mbps) and minimal latency, but requires a physical connection.Ideal for laptops or PCs when Wi-Fi is not available and Bluetooth is too slow.
How to set up:
- Connect Xiaomi 8 Pro to your computer through the original USB-cable (better to use port) USB 3.0 on PC).
- On the smartphone in the notification that appears, select File Transfer (MTP) → USB-modem.
- If the option does not appear automatically, go to Settings → The Internet and the Internet → Access Point and modem and turn on USB-modem.
If the Internet is not working, check the modem drivers (usually installed automatically on the first connection).
What to do if Windows can’t see USB-modem?
4. Comparison of distribution methods: speed, charge, compatibility
The choice of method depends on your tasks. Below is a table with key parameters:
| Parameter | Wi-Fi | Bluetooth | USB |
|---|---|---|---|
| Max, speed. | 150–433 Mbps | 3-5 Mbps | up to 300 Mbps |
| Number of devices | 8 | 1 | 1 |
| Battery consumption | high (~15%/hour) | low (~5%/hour) | Medium (~10%/hour) + USB charging |
| Delay (ping) | medium (30–50 ms) | high (100-200 ms) | minimum (10-20 ms) |
| Compatibility | all-wi-fi devices | devices with Bluetooth 4.0+ | PC/laptop from USB-port |
Critical nuance for Xiaomi 8 Pro: when you give Wi-Fi at a frequency of 5 GHz, the smartphone can overheat if the ambient temperature is above 30°C. In this case, MIUI It automatically lowers the frequency to 2.4 GHz or shuts down the access point. USB-hot-weather modem.
Wi-Fi (access point) |Bluetooth|USB|No distribution-->
Typical problems and their solutions
Even after you set it up correctly, you can get errors.
❌ Error 1: Access point is turned on, but devices are not connected
Causes and solutions:
- 🔍 Incorrect password: check the register of letters (password) Qwerty123 ≠ qwerty123).
- 📵 Operator restriction: Some tariffs block distribution (see below).
- 🔄 Conflict IP: On the connected device, set to receive IP automatically (in network settings).
❌ Mistake 2: Connected but no Internet
The operator is most often to blame.
- 📱 APN-Settings: Go to Settings → SIM-maps and mobile networks → Access point (APN) Compare with your operator’s parameters (for example, for MegaFon: Internet, for Tele2: tele2.internet).
- 💰 Internet Distribution Option: Check with the operator if it is included in your tariff (sometimes requires a separate activation).
- 🔄 Reboot: Turn off the access point, restart the smartphone and turn it on again.
❌ Error 3: Access Point shuts down after 5-10 minutes
This is a MIUI security feature if the smartphone is not connected to the charger.
- 🔌 Connect Xiaomi 8 Pro to the charger.
- 🛠️ Turn off battery optimization for modem function: Settings → Battery → Energy saving applications → Three points (⋮) → Additionally. → Optimizing the battery → Find "Access Point" and select "No Limitations".
💡
If none of these methods worked, try resetting your network settings: Settings → System → Settings Reset → Resetting your Wi-Fi, mobile network, and Bluetooth settings.
6. How to save traffic when giving out the Internet
Mobile Internet can quickly eat up gigabytes of traffic, especially if connected devices are updating or downloading files in the background.
- 📊 Limit background traffic: on a connected device (laptop/phone) disable automatic updates of applications and OS.
- ⏳ Set the limit: in MIUI There's a built-in traffic metering feature. Go to Settings. → SIM-maps and mobile networks → Traffic. → Set a limit on mobile data.
- 🔍 Block “gluttonous” devices: in the settings of the access point (Settings) → Access Point and modem → Wi-Fi hotspot → Connected devices can be blocked by individual gadgets.
- 📵 Use it. VPN With traffic compression: apps like Opera Max (outdated, but there are analogues) compress data to 50%.
If you often give out the Internet, consider unlimited rates (for example, MTS Smart Unlimited or Beeline Beeline No Limits for everything). Conventional "unlimited" rates often have a limit on modem traffic (for example, 10-20 GB per month).
7. Alternative ways of distribution (for advanced)
If standard methods don’t work or additional features are needed (for example, handouts on schedule), third-party solutions can be used.
🔧 Method 1: NetShare application (without root)
NetShare allows you to distribute the Internet even if the operator blocks a standard access point. Install it from Google Play and follow the instructions in the application. Minus - the speed is limited to 5-10 Mbps in the free version.
🔧 Method 2: ADB-Teams (for experienced teams)
If the access point is disabled by itself, you can cancel this restriction via ADB:
- Connect Xiaomi 8 Pro to your PC and enable USB Debugging (Settings → About Phone → MIUI Version → 7 times tap on version → Return to Additional → For developers → Debugging on USB).
- Open the command line on PC and type: adb shell settings put global tether_dun_required 0
- Reboot your smartphone.
This command disables the DUN (Dial-Up Networking) check, which some operators use to block the distribution.
⚠️ Attention: Use ADB-Teams may disrupt some functions MIUI. Before experimenting, back up the data through Settings → Additionally. → Backup and reset.