How to Enable GPRS on Xiaomi: A Complete Guide with Pictures and Tips

Mobile Internet on Xiaomi smartphones sometimes refuses to work even if there is a network signal. Most often, the problem lies in the wrong settings of the access point (APN) or disabled data mode. In this article, we will discuss how to turn on GPRS, 3G or 4G on Xiaomi devices – from low-cost Redmi to flagship Mi and POCO.

It is important to understand that the term «GPRS» Today it is used more out of habit: modern smartphones automatically connect to faster networks (Edge, 3G, 4G/5G), But the principle of the setup remains the same. SIM-The Internet stopped working - do not rush to carry the phone to the service. 90% In some cases, the problem is solved for 5 minutes through the settings menu.

We will look at this in detail:

• 🔍 How to check if mobile Internet is enabled on Xiaomi
• ⚙️ Manual and automatic creation of access points (APN)
• 📶 Choice of type of network (2G/3G/4G) and priority
• 🛠️ Solving common errors (no network, an “E” icon instead of a “E” icon) 4G, restricted access)

1. Check basic settings of mobile Internet

Before you go into deep settings, make sure that mobile internet is activated at all. On Xiaomi with the MIUI shell (versions 12-15), the path to options may be slightly different, but the general logic holds.

Open the Settings. → SIM-Maps and mobile networks. Here you'll see two key options:

• 📱 Mobile data is the main switch of the Internet. If it's gray, the Internet is off.
• 🔄 Data transfer mode – here the type of network is selected (2G, 3G, 4G). If it's "Only" 2G», The smartphone will not catch 4G.

Attention: If you have two SIM-Check that mobile data is included for the correct SIM. Xiaomi’s default Internet can be tied to a slot SIM1, Even if you use the second card.

⚠️ Note: On some models (e.g, POCO X3 Redmi Note 10 after the update MIUI reset APN. If the Internet disappeared after the update – check the access points manually (more on this below).

2. Automatic setting of APN (Access Points)

Most operators (MTS, Beeline, MegaFon, Tele2) automatically send Internet settings when you first install them. SIM-If this does not happen or the settings are lost, you can request them again.

Instructions for automatic setting:

1. Go to Settings. → SIM-maps and mobile networks → [choose SIM] → Access points (APN).
2. Click on the three dots in the top right corner and select Reset to default values.
3. Send. SMS with the text of the Internet (or Internet) to the short number of your operator: 📱 MTS: 1234 📱 Beeline: 06503 📱 MegaFon: 5049 📱 Tele2: 679

Reboot your smartphone.

Make sure that SIM-Card active (not blocked)

Check the balance (at some rates, the settings are paid)

Disable VPN (can block SMS from the operator)

Reboot your phone before requesting settings-->

If after these actions, a new profile appears on the APN list (usually with the operator name), select it and save it. the Internet should be up in 1-2 minutes.

3. Manual creation of APN for GPRS/4G

If the automatic setting doesn’t work, you’ll have to enter the settings manually, and the following are the current settings for major Russian operators (tested in 2026).

To add APNs manually:

1. Go to Settings. → SIM-maps and mobile networks → [yours SIM] → Access points (APN).
2. Click Add (+ icon in upper right corner).
3. Fill in the fields as above. Leave the rest of the parameters (e.g. MCC, MNC) unchanged.
4. Save your profile and select it from the list.

💡

If after saving the APN disappeared from the list, check if the tick in the field Type APN as default,supl,mms.

4.Selection of network type (2G, 3G, 4G) and priorities

Even if the APN is set up correctly, the smartphone can “hang” on a slow network (for example, show an “E” icon instead of “4G”).

To change the type of network:

1. Open the Settings. → SIM-maps and mobile networks → [choose SIM].
2. Click Network Type (or Preferred Network Type)
3. Choose one of the options: 📶 4G (preferably)/3G/2G — Optimal mode for most users. 📶 Only 4G (LTE) — If you have good coverage in your area 4G, But the smartphone is constantly switching to 3G. 📶 Only 3G — if 4G unstable, but 3G better. 📶 Only 2G — Maximum battery savings (the internet is very slow).

On some Xiaomi models (e.g. Redmi 9A or POCO M3), the Network Type menu may not have the option “4G Only” option. In this case, select “4G/3G/2G (auto)” and disable 2G forced use (if activated) in the developer settings.

5. Solving Common Problems with GPRS/4G

If after all the manipulations the Internet has not worked, check the following points:

🔴 Problem: Badge "E" or "H"+» instead 4G

This means that the smartphone is connected to the Edge (2G) or 3G network, although 4G is available.

• 📵 In the settings selected Only 2G/3G (see section 4).
• 📡 Weak signal. 4G in your area (check the coverage on the operator's website).
• 🔧 Nana SIM-map disabled service 4G (Call for operator support).

🔴 Problem: Connection is there, but pages are not loaded

Possible causes:

• 🛡️ Blocking traffic with antivirus or VPN (Turn them off temporarily).
• 💰 Internet traffic is over or zero balance is activated».
• 🔄 Wrong. APN-protocol (should be IPv4/IPv6 or IPv4).

🔴 Problem: The connection is constantly missing

This is typical for devices with unoriginal firmware or after a failed update.

• 🔄 Reset network settings: Settings → System system → Reset → Reset the network settings.
• 📱 Check if the beta version is installed. MIUI (they often glitch).
• 🔧 Update the modem firmware (requires an unlocked bootloader).

💡

If the Internet is up and running after resetting, but it's gone again a day later, the problem is the application conflict. Check out the recently installed programs (especially optimizers and cleaners).

6. Features of customization on older Xiaomi models

On Xiaomi 2016-2018 smartphones (e.g. Redmi 4X, Mi A1, Redmi Note 5), the MIUI interface is different and some features may not be available.

• 📱 On Mi. A1/A2 (with pure Android, the path to APN: Settings → Wireless networks → More. → Mobile networks → Access points.
• 🔧 On the Redmi. 3S/4A There is no option "Only" 4G» — maximum 3G/2G (motor-car).
• 📶 On some devices after the shift SIM-The card requires manual modem restart: type in dial ##4636##, select Phone Information and click Turn off the radio, then Turn on the radio.

For owners of old models, the problem with outdated frequencies is also relevant. 4G. For example, Redmi Note 3 Pro does not support Band 20 (800 MHz) and Band 3 (1800 MHz), which are actively used by operators in 2026. 4G-modem.

7. Additional Tips for a Stable Internet

To ensure that mobile Internet on Xiaomi works without failure, follow these recommendations:

• 🔄 Update your firmware regularly. MIUI Correct modem errors. Check the updates in Settings → The phone. → Updating the system.
• 📵 Turn off traffic savings in Settings → Battery and productivity → Traffic savings – it can block background connections.
• 📡 Use network monitoring applications such as NetMonster or LTE Discovery to check the real speed and type of connection.
• 🔧 Reset your network settings if the internet is lost after an update or change SIM-map.

Note: If you use two of these SIM-cards, one of them can only be configured for calls (without the Internet). → SIM-maps and mobile networks → [choose SIM] → Use and enable the option Mobile Data.

💡

In some models (for example, POCO F3) There is a hidden function of Dual. 4G, permitting SIM-maps simultaneously work on the network 4G. Activated via the Engineering Menu (#4636##) or Activity Launcher app (Look for Dual) 4G Settings).

FAQ: Frequent questions about setting up GPRS on Xiaomi