How to properly install SIM-Map in Xiaomi Redmi 10: instructions with photos and tips

Introduction: Why the Right Installation SIM-The maps are important for Redmi 10

Xiaomi Redmi 10 (model 2021) remains one of the most popular budget devices due to balanced performance and support for the two SIM-But even a simple operation like installing a map. SIM, It can cause difficulties for beginners, and an incorrectly inserted card can cause a network to be missing, no service errors, or even damage to the slot.

In this article, we will analyze not only the basic installation instructions, but also the nuances that the manufacturer is silent: how to choose a type of equipment. SIM-maps (nano-SIM or eSIM?) where the slot is in different versions of Redmi 10, and what to do if the phone does not see the operator after installation.

If you have just purchased Xiaomi Redmi 10 or are planning to change operators, save this article. It will save you time and eliminate the need to contact the service center for trifles.

What are they? SIM-Xiaomi Redmi 10: nano-SIM, micro-SIM or eSIM?

The Redmi 10 (M2101K7AG for the global version) is equipped with a hybrid slot that supports:

• 📱 Two nano-SIM (format) 4FF, size 12.3×8.8 mm – standard for modern smartphones.
• 🔄 One nano-SIM. + microSD card (up to 512 GB) – if you need to expand the memory.

Redmi 10 does not support eSIM – virtual SIM-cards that are activated through software.If your carrier only offers eSIM (for example, some rates) Tele2 Tinkoff Mobile, you will have to order a physical nano-SIM.

How to determine the type of your SIM-map?

⚠️ Warning: If you decide to trim the micro-SIM to nano-SIM yourself, use a special template or scissors with thin blades. Sloppy trimming can damage the chip - and the card will have to change.

Where is the slot for SIM-card in Xiaomi Redmi 10: photos and schemes

Unlike Xiaomi’s flagship models, where the slot can be placed on top or side, Redmi 10 has it on the left side (when you look at the screen).

• 🔍 Small hole for paper clip/tool (diameter) ~0.8 mm).
• 📌 Logo. SIM or card icon near the hole.
• 🔧 On some modifications (for example, Redmi 10 Prime) the slot can be marked with a red dot.

If you can’t find the slot, check out:

1. Remove the cover - it can close the hole.
2. Light a flashlight - sometimes the slot is poorly visible in low light.
3. Make sure you keep your phone on the screen (not the back).

⚠️ Note: Do not confuse the slot for SIM-cards with a hole for the microphone (located at the bottom next to the connector) USB-C) Or an infrared port (top) trying to insert a paper clip into those holes could damage the device!

💡

If you do not have a special paperclip to remove the tray, use an unbended stationery clip or a needle from the syringe (the diameter should not be more than 0.8 mm).

Step-by-step instruction: how to insert SIM-Map in Xiaomi Redmi 10

Before starting, make sure that:

Turn off your smartphone (not necessarily, but recommended)

Prepare a paper clip or tool to remove the tray

Check that SIM-The card is trimmed to nano-SIM format

Make sure there are no scratches or chips on the map-->

Now follow the instructions:

1. Remove the tray for SIM-Cards: Put the paperclip in the hole on the left face to the end (should be a slight click). Pull the tray over yourself, it will extend about 5 mm. Carefully get the tray out completely without exerting effort.
2. Install. SIM-Map(s): Place the tray on a flat surface with the contacts up. Place the nano-SIM in the first slot (marked as SIM (1) or in the second (SIM (2) If you use two SIM-Make sure they don’t overlap the microSD area (if there is one).
3. Put the tray back: Carefully insert the tray into the slot to the end (must click). Make sure the tray is not protruding and sits flat.

After installation, turn on the phone (if it was turned off) and wait for the network icon to appear in the status bar. If the network does not appear within 1-2 minutes, go to Settings → SIM-Maps and mobile networks and check the connection status.

💡

Never put a tray in the tray with SIM-The card is inside out, which can damage the slot contacts. Right position: the gold contacts of the card should be facing downwards (to the back of the phone).

How to activate a mobile network after installation SIM-map

Successful installation SIM-And the maps are only half the story, and the phone needs to catch the network:

1. Turn on SIM-map in settings: Go to Settings → SIM-maps and mobile networks. Choose yours. SIM-map, SIM Activate the switch, Turn on (if it is off).
2. Set up Network Mode: In the same menu, select Network Type. For better internet speed, set 4G (preferably) or 3G/4G (auto).
3. Enter. PUK-code (if required): If SIM-The card is blocked, a request will appear on the screen PUK-The code is on the plastic holder that came with the SIM-card.

If the network does not appear after these actions:

• 🔄 Reboot the phone.
• 📶 Check your carrier’s coverage area (you may be out of range).
• 🔧 Manually select the operator in Settings → Mobile network → Network operators.

⚠️ Attention: If after installation SIM-The phone says "No service" or "SIM-- the card is not found, do not try to insert the card again - this can damage the contacts. SIM-cards (wipe them with a soft cloth) are the contacts in the slot bent (light with a flashlight) or does the case block the antenna (take it off and check the signal).

Common errors in installation SIM-maps and how to avoid them

Even experienced users sometimes make mistakes that lead to network problems, and here are the most common ones:

Another common problem is the loss of a paper clip to retrieve the tray, and if you don't have a replacement on hand, you can use:

• 📎 Opened paper clip (diameter) ~0.7-0.8 mm).
• 🪡 Syringe needle (pre-wipe with alcohol).
• 🔧 Special tool from the remix for phones (sold in AliExpress or electronics stores).

Don't use:

• ❌ Dental cleanses (may break inside).
• ❌ The pins (too thick, will damage the hole).
• ❌ Knives or scissors (risk of scratching the body).

What to do if Xiaomi Redmi 10 does not see SIM-map

If you have correctly installed SIM-The card, but the phone does not recognize it, follow this algorithm:

1. Check the physical condition of the card: Get it out SIM-Check the card for scratches, chips or dirt, wipe the contacts with a soft cloth (you can moisten in alcohol).
2. Reboot the phone: Hold the power button for 10 seconds, then turn the device back on.
3. Update your network settings: Go to Settings → SIM-maps and mobile networks → [yours SIM] → Access point (APN). Click Reset settings (options) APN load automatically).
4. Check the slot for damage: Light a flashlight into the slot - contacts should be smooth, without bends. If contacts are bent, do not try to straighten them yourself - contact the service.
5. Test it. SIM-card in another phone: If the card does not work in another device, the operator has a problem (possibly, SIM blocked).

If none of the methods helped, the module may have failed. SIM-- The cards are on the phone:

• Contact the Xiaomi Service Center (guarantee case).
• Check if moisture has entered the phone (even a small amount can oxidize the contacts).

💡

If the phone stopped seeing SIM-If you drop or get moisture, don't try to dry it with a hair dryer or rice, it will make the problem worse.

FAQ: Answers to Frequent Questions about SIM-Maps in Xiaomi Redmi 10