How to improve Bluetooth in Xiaomi smartphones: from settings to hardware solutions

The weak Bluetooth signal on Xiaomi is one of the most common problems faced by smartphone owners of the brand: from headphones Redmi Buds constantly switch off, the Mi Portable Speaker starts to “hritter”, the Mi Band smart watch loses communication at the most inopportune moment, the reasons can be hidden in software failures MIUI and hardware limitations of the Bluetooth chip — especially in budget models like the Redmi Note 12 or POCO X5.

In this article, we’ll break down 7 working ways to improve your Bluetooth connection on Xiaomi, from basic settings to advanced stunts with firmware and hardware.

• 🔍 Diagnose the source of the problem (software, iron, or interference)
• ⚡ Optimize settings MIUI stable-connection
• 📡 Enhance the signal with hidden features and third-party applications
• 🛠️ Solve hardware limitations (if any)

Importantly, some methods require unlocking the bootloader or root rights, which we'll mark separately. Let's start with the simplest ones.

1. Basic settings check: Bluetooth version and compatibility

Before digging deeper, make sure the problem isn't with device incompatibility or an outdated version of the protocol.For example, Sony's WH-1000XM5 headphones with Bluetooth 5.2 can conflict with Xiaomi's Mi 10T smartphone (version 5.1) if the correct codec isn't activated.

How to check the Bluetooth version on Xiaomi:

1. Open Settings → About the phone → All the characteristics.
2. Find the line “Bluetooth version” (e.g. 5.0, 5.2, 5.3).
3. Compare with the requirements of your gadget (specified in the instructions or on the manufacturer's website).

Xiaomi smartphones on the Qualcomm Snapdragon 4xx/6xx chip (e.g. Redmi 9A, POCO M4 Pro) often have stripped-down Bluetooth modules with a weak signal – this is a hardware limitation that cannot be fixed software.

If your model is in the table, try these solutions. If not, move on to the next step.

2. Optimization of MIUI settings for stable connection

MIUI hides a few important parameters that directly affect Bluetooth quality, such as the default power saving mode for wireless connections, which can cut off communication when the battery is low.

What needs to be done:

Turn off power saving mode for Bluetooth|Change the codec to a compatible one|Turn off Dual Audio (if not in use)|Update the firmware to the latest version-->

• 🔋 Turn off energy saving: Go to Settings → Battery and productivity → Select battery mode and select Performance. Then in Settings → Connections and sharing → Bluetooth disable the Bluetooth Energy Saving option (if available).
• 🎵 Change the audio codec: In the settings of the connected device (for example, headphones), tap the icon ⚙️ and select the codec AAC or aptX (if supported). SBC It is of poor quality, but it works more stable on weak chips.
• 🔊 Disable Dual Audio: Simultaneous Sound Transfer to Two Devices (Bluetooth Settings) → Additionally. → Dual Audio is often a jamming feature. Turn it off if you're not using it.

Hidden setting: Xiaomi has an undocumented parameter bluetooth_a2dp_hw_offload, It can improve the sound quality, it can activate it:

1. Enable Developer Mode: 7 times tap the MIUI version in Settings → About Phone.


2. Return to Settings → Additional → For developers.




3. Find the option to turn off hardware acceleration A2DP (Bluetooth) and turn it off (the option must be turned off to improve sound).

⚠️ Note: On some models (Redmi 9, POCO M3) This option can cause the opposite effect – check the sound after the change!

3. Software solutions: applications and firmware

If MIUI settings didn't work, you should turn to third-party tools.

• 📶 Enhance signal by optimizing protocol (e.g. Bluetooth Auto Connect).
• 🔄 Automatically reconnect devices when cliffed (e.g., Tasker) + plugin AutoBluetooth).
• 🛠️ Clean Bluetooth cache (e.g., Bluetooth Repair).

Top.-3 Applications to improve Bluetooth on Xiaomi:

If apps didn't work, consider flashing. Custom firmware like LineageOS or Pixel Experience often optimizes Bluetooth drivers better than stock MIUI, for example.

• 🔓 Unlock the bootloader (instructions for Xiaomi here).
• 📥 Installations TWRP and the firmware itself.
• ⚠️ Warranty losses (on new models).

⚠️ Note: On models with a MediaTek chip (e.g., Redmi Note 11 on Helio) G88) Custom firmware can worsen Bluetooth performance due to unstable drivers!

💡

Before you run the firmware, back up the persist partition via TWRP, which stores the calibration data of the Bluetooth module, and without it, the sound in the headphones can disappear after the firmware!

4. Hardware restrictions: what to do if the problem is in the iron

If none of the software methods worked, the problem may lie in the hardware:

• 📶 Weak Bluetooth antenna (typical for budget models).
• 🔌 Poor connector contact (for example, after a phone drop).
• 🔋 Battery wear (at a discharge below 20%, the Bluetooth module may be switched off).

How to diagnose a hardware problem:

1. Connect your headphones to another phone – if it works, your Xiaomi is the problem.
2. Check if the upper part of the body is warm (the module is located there). Bluetooth/Wi-Fi). Overheating = defect.
3. Run the hardware test through the engineering menu: ##4636## → Device Information → Equipment Test → Bluetooth Test If the test shows errors (e.g. Bluetooth status: Failed), this confirms a hardware failure.

Solutions for hardware problems:

• 🔧 Antenna soldering (cost) ~1500–3000 ₽ Relevant to Redmi's service center. 9/9A, where the antenna often departs from the board.
• 📲 Replacement of Bluetooth module (from 2000) ₽). Required on models with physical chip damage (for example, after moisture is ingested).
• 🔄 Use of an external Bluetooth adapter (via a USB-C). Suitable for Xiaomi 12/13 Pro with support OTG.

5. Interference Removal: Wi-Fi, 5G and other noise sources

Bluetooth operates at 2.4 GHz — the same frequency as Wi-Fi, microwaves, wireless mice and other devices — and if you have a lot of these gadgets in your apartment, they create interference that makes communication unstable.

How to reduce interference:

• 📡 Change Wi-Fi channel: Select channel 1, 6 or 11 (they least intersect with Bluetooth) in router settings. Avoid automatic channel selection.
• 📵 Turn it off. 5G (if not in use: Module 5G It can interfere with Bluetooth. Try switching to Bluetooth. 4G In Settings → SIM-maps and mobile networks → Preferred type of network.
• 🔌 Remove sources of interference: Microwave, wireless charging, USB-Hubs, all of these things can get in the way. Test the connection in different parts of the room.

💡

If you have a router that supports Wi-Fi 6 (802.11ax), turn on BSS Coloring mode in its settings – this reduces interference for Bluetooth devices.

To check for interference, use the WiFi Analyzer (Android) app, if you have many neighbors on the same channel, that's why Bluetooth breaks.

Specific problems and solutions

Some Xiaomi models have unique Bluetooth bugs, and here are the most common:

If your model is not in the table, but the problem is specific, check out forums like 4PDA or MIUI SU.

7. Alternative ways of connecting

If Bluetooth on Xiaomi has not worked consistently, consider the alternatives:

• 🎧 Wired headphones through USB-C For example, Xiaomi Type-C Earphones give better sound quality without delay.
• 📡 Wi-Fi Direct or Miracast for audio transmission to speakers/TV (e.g. via Google Cast).
• 🔌 Bluetooth adapter (external). Connects via USB-C It works as a separate module: 1Mii B06 Pro (supports aptX) LL).

When to use alternatives:

• If you need a minimum response time (for example, for games or watching videos).
• If Xiaomi physically cannot provide a stable signal (e.g. Redmi 8A with Bluetooth 4.2), it is not possible to provide a stable signal.
• If you connect multiple devices at the same time (Bluetooth is not designed to do this).

💡

An external Bluetooth adapter is the only solution for models with broken internal modules if repair is impossible or too expensive.

FAQ: Frequent questions about Bluetooth on Xiaomi