How to remove the inscription “Roaming” on the Xiaomi phone: all ways

Xiaomi’s Roaming Icon Is One of the Most Common Problems Faced by Redmi Smartphone Owners, POCO And it's even when you're not in your home region, and sometimes you're not active at all. SIM-What's the reason? Most often it's a mobile network failure, an operator error, or the consequences of a firmware update.

In this article, we will analyze all working ways to remove the roaming icon – from basic (reboot, manual network configuration) to advanced (reset). APN, You will also learn why the indicator can appear on phones with two SIM-If you see an "R" or "R" in the status bar, follow the instructions below.

Why does the roaming icon appear on Xiaomi

Before you take down the indicator, it's important to understand the nature of the indicator, because the roaming icon (letter "R" or "R") signals that the phone is connected to another carrier's network, for example, when traveling abroad, but 80 percent of the time it occurs mistakenly, even when you're in your home region, the main reasons are:

• 🔄 Failure in mobile network settings – the phone “forgot” the home operator and tries to connect to someone else’s network.
• 📱 Problems with SIM-Card – physical damage, improper installation or outdated data on the chip.
• 📡 Operator error – temporary problems on the provider side (for example, MTS, Beeline, MegaFon).
• 🔧 Wrong parameters APN — post-refresh MIUI Access points are lost or missing.
• 📲 Two. SIM-Cards – conflict between slots (for example, one card roaming and the second – no).
• 🤖 System glitch – after firmware or resetting, the phone incorrectly determines the network.

Interestingly, on some Xiaomi models (for example, Redmi Note 10 Pro or POCO X3 Pro), the roaming icon can appear even when mobile data is disabled, due to the peculiarities of the ModemConfig module in firmware based on Android 11+.

⚠️ Note: If you have recently crossed the border and the roaming icon appears naturally, do not force it to be disabled. SMS.

Method 1: Reboot the phone and check SIM-map

Start with the simplest thing, rebooting your device, and 30 percent of the time, it helps you reset the time errors of the communication module.

1. Press the power button for 2-3 seconds.
2. Select “Reset” (not “Switch off!”).
3. Wait for the full system load (1-2 minutes).

If the reboot didn't help, check your physical condition. SIM-map:

• 🛠️ Remove the tray for SIM with a paper clip (hole near the slot).
• 🔍 Check the map for scratches, chips, or contamination (especially contacts).
• 🔄 Reinstall the card to the slot (try swapping the slots if you have two). SIM).
• 📱 If the card is old (more than 5 years old), contact the operator for a replacement - the chip may wear out.

If after reinstalling the SIM, the roaming icon disappeared, but soon reappeared, the problem lies in the network settings.

Method 2: Manual selection of mobile network

Often, Xiaomi's phone automatically connects to an "alien" network due to a glitch in the operator's search algorithm.

1. Open the Settings. → SIM-maps and mobile networks.
2. Choose yours. SIM-card (if two of them).
3. Slip on the item "Network Operators".
4. Turn off the Automatic Selection option (the slider should turn grey).
5. Wait for the phone to find the available networks (it can take up to 30 seconds).
6. Manually select your operator (for example, MTS-RU or Beeline RUS).
7. Save the changes and restart the phone.

If your operator is not listed or if you have a “failed to register” error, try:

• 🔄 Turn on and off again "Automatic choice».
• 📶 Switch to the network 2G (customized SIM-map → «Network type) then return 4G/LTE.
• 📴 Temporarily disable mobile data and turn it on again.

⚠️ Attention: On some firmware MIUI 13/14 After manual network selection, the phone may "forget" the operator after restarting. In this case, you will need to reset the network settings (see Method). 4).

Rebooted phone is performed

SIM-card is clean and properly installed

The problem persists after manual network selection

Mobile data is enabled and working (check the internet)

-->

Method 3: Update APN Access Points

Wrong parameters APN (Access Point Name is a common cause of false roaming, especially if you've recently changed your fare, operator, or firmware update. APN:

1. Go to Settings. → SIM-maps and mobile networks → [Yours. SIM] → Access points (APN).
2. Click on the three dots in the top right corner and select Reset to Default Values.
3. If the reset didn't help, add APN manually: Click "Add APN." Enter your carrier's details (see table below). Save and select the new APN as active.

After adding APN, restart your phone and check for the roaming icon to disappear. If the problem persists, try removing all saved APNs and repeat the procedure.

💡

If you have two. SIM-maps, updates APN Sometimes roaming is caused by a conflict of settings between slots.

Method 4: Resetting network settings

If previous methods failed, perform a complete reset of network settings, which will delete all stored Wi-Fi networks, passwords, Bluetooth and mobile settings, but often solves the roaming problem.

1. Open Settings → About the phone → Reset settings.
2. Select “Reset Network Settings” (not to be confused with “Reset to factory settings!”).
3. Confirm the action (you may need to enter a pattern lock or PIN-code).
4. After resetting, the phone will reboot automatically.

⚠️ Attention: On phones with MIUI 14 and a newer network reset may also remove settings VPN and double SIM. Write down important parameters in advance.

💡

Network resetting is the most effective way to fix mobile communication software errors, but only use it if other methods have not worked.

Method 5: Advanced Methods (for Power Users)

If the roaming icon never goes away, the problem may lie in system files or firmware, which require caution and are only suitable for users familiar with Android settings.

1. Editing ModemConfig parameters

On some Xiaomi models (e.g. Redmi 9T or POCO F3), it helps to change the modem configuration via the engineering menu:

##4636## → Phone Information → Select Network Type: LTE Only

If this does not work, try entering:

##72786##

This will reset the SCRI settings. Once you enter the code, the phone will restart.

2. Delete the spn-conf.xml file (requires root)

If you have root rights, you can manually delete the operator configuration file:

1. Install a file manager with root support (such as Root Explorer).
2. Go to /data/data/com.android.providers.telephony/databases/.
3. Delete the telephony.db file.
4. Reboot the phone.

⚠️ Warning: Incorrect editing of system files can result in loss of communication or cyclical phone reboot!

3.Firmware through Fastboot

If roaming appears after the MIUI update, it is possible that the firmware is installed with errors.

• 🔧 Download the official firmware for your model from the Xiaomi website.
• 📥 Use the Mi Flash Tool for clean installation via Fastboot.
• 🔄 After the firmware, perform the reset to factory settings.

Frequent Questions (FAQ)