Owners of the Xiaomi Redmi Note 8 smartphone using the Phoenix operator often face the need to manually configure network settings. SIM-If you're on a map or loaded by the system on your first run, you sometimes need to have manual intervention, and that might be due to a firmware update. MIUI, resetting settings to factory or simply with the desire to optimize the connection speed.
Properly configuring an APN hotspot is critical to the stable operation of mobile broadband. Without the correct data, the device will not be able to log in to the operator's gateways, which will lead to no Internet even if there is a network signal. In this article, we will discuss in detail the process of creating and editing profiles for your gadget.
We're going to look at not only the standard algorithm, but also the nuances that you might encounter on the MIUI shell. Understanding network protocols will help you quickly diagnose communication problems. Be prepared for the fact that the interface may vary slightly depending on the version of Android, but the logic of actions will remain the same.
Device preparation and verification SIM-map
Before you go to the settings menu, you need to make sure the connection is physically healthy. SIM-The Phoenix operator's card is set correctly and readable by the system. Put the tray in using a special key, and wait for the network indicator to appear in the status bar. SIM-maps, try to wipe the contacts of the chip with a soft cloth.
It is important to check whether the carrier-side data service is activated, sometimes the balance can be blocked or the traffic limit is exhausted, making it impossible to access the global network even with the right parameters, and make sure that the mobile data module is included in the phone settings.
Check if there is a flight mode that completely disables the radios. To quickly access these features, lower the notification curtain from top to bottom. Make sure the 4G or LTE icon is displayed next to the signal level, not just the voice icon.
☑️ Checking before setting up
If you just updated your Redmi Note 8 firmware, the system could reset old profiles, so creating a new hotspot is a must. Don't ignore this step, as old configurations may conflict with new network protocols.
Enter the network settings menu on MIUI
The MIUI shell interface installed on Xiaomi has its own specific layout of elements. To start setting up, open the main app menu and find the Settings icon. It is usually a gear and is located on the first screen or in the Tools folder.
In the list of parameters, scroll down to the section "SIM-Maps and mobile networks. That's where all the major communication management tools are concentrated. Click on this to go to the detailed settings of your SIM card.
If you have two devices installed in your device SIM-If you have a card, the system will tell you to choose the one that you want to change, and you can select the slot that holds the Phoenix card, and it's critical that you don't change the settings of the other operator by accident.
💡
If you can't find the menu item you want, use the search bar at the top of the settings screen, type "APN" or "Access Points" and the system will redirect you to the desired section.
Next, you will need to find the "Access Points" item (APN)". It can be in the main menu or hidden in an additional list, accessible through three dots in the corner of the screen. MIUI The path may look like settings. → SIM-maps and mobile networks → Access points (APN).
Creating a new APN access point
Once you log into the access point menu, you'll see a list of existing profiles. To add a new option, click on the plus icon or the New APN button, which is usually located in the lower right corner or in the action menu, which will create an empty template that you need to fill in.
In the form you open, you'll need to enter a few key values, and the most important field is "Name." Type a name that you can use, like Phoenix Internet, which is just for your convenience, to distinguish your profile from the others.
The APN field (or Access Point) is the most important technical parameter. This is where the operator's gateway address is written. For Phoenix, you need to enter the Internet.phoenix value (or the current address provided by the operator if it changes). The letter register usually doesn't matter, but it's better to stick to the lower case.
⚠️ Note: Do not change the Proxy and Port fields unless the operator has explicitly specified such requirements, leaving these fields empty or with standard values will prevent server connection errors.
Once you have entered, be sure to click the Save button or the three dots in the corner of the screen and select Save. If you just go back, the input data may not be written to the device's memory. Make sure the profile you create is marked with a circle or highlighted, which means it is activated.
What if the APN field is not saved?
Table of basic parameters for the Phoenix operator
For ease of perception and validation of the entered data, check the table below. It contains the standard values that are used by most subscribers in the network of the operator.
| Parameter | Meaning | I'll be sure. |
|---|---|---|
| Name (Name) | Phoenix | Yes. |
| APN | internet.phoenix | Yes. |
| proxy | (empty) | No. |
| Port port | (empty) | No. |
| Type APN | default,supl | Yes. |
Note the APN type field. If you want MMS messages to work correctly, you should add a comma value to the mms if the operator provides such services.
💡
The accuracy of the APN address input is crucial, and one extra letter or space can result in a complete lack of access to the Internet, even if the network signal is full.
Additional settings and protocols
For a modern 4G/LTE network, which Redmi Note 8 supports, it is recommended to set the APN protocol to IPv4/IPv6, which will ensure compatibility with all modern services and sites.
The "Authentication Type" option is better left on the PAP or CHAP value, or choose "No" if the connection is installed without problems, which is rarely required, but can help in cases where standard authorization does not pass.
Some users try to change the MCC and MNC field, which is strongly discouraged because these codes are tightly tied to the region and operator, and their change can cause the phone to stop seeing the network altogether or to work incorrectly in roaming.
If you use your smartphone to distribute the internet, make sure that the hotspot settings do not have a limit on the type of connection. The hotspot also requires an active APN profile with the right settings.
Diagnostics and troubleshooting
Sometimes all the settings are correctly entered, but the Internet is not working. First of all, try to reboot the device. This is a standard procedure that allows you to reset temporary errors in the network stack and re-register with the operator's network.
Check if the data is activated for a particular application. MIUI has a traffic saving feature that can block network access for background processes or even for a browser. Go to the application settings and make sure that mobile Internet access is allowed.
If the problem persists, try to delete the APN profile you created and recreate it by carefully rechecking each character, sometimes resetting the APN settings to factory values through the access point menu (Reset or Restore by Default button).
⚠️ Attention: If after all the manipulations the Internet did not appear, the problem may be on the operator's side. SIM-maps and availability of work on the network.
It’s also worth checking whether data saving is included in the system’s global settings, which restricts background activity and can interfere with the normal operation of some services, creating the illusion of a broken Internet.