How to set up the Internet on a Xiaomi TV: Wi-Fi, cable and troubleshooting

Xiaomi's modern TVs are not just TV-channel screens, but full-fledged multimedia centers with access to streaming services, YouTube, a browser and even games. But all these features become useless without a stable Internet connection. TV It may seem like a trivial task, but in practice users are faced with nuances: from hidden settings of the router to the features of the firmware of specific models (for example, Mi). TV Q2 or Mi TV A Pro).

In this article, we will examine all possible ways of connecting – from standard Wi-Fi to wired Ethernet, and also consider typical errors (such as the absence of a single connection). IP-We will pay special attention to hidden Xiaomi settings, which the manufacturer does not advertise, but which can significantly improve connection stability. If your TV suddenly lost its network after an upgrade or reset, here are steps to restore access.

1. Preparation for setting up the Internet: what to check before connecting

Before you start setting up your network on your TV, make sure that the problem is not caused by external factors. Experience shows that 60% of the time the Internet is unstable on Mi. TV It is not connected to the device itself, but to the router or provider.

Here is the mandatory checklist before setting up:

• 🔌 Power router: restart it (turn it off for 30 seconds and turn it back on). DHCP-servers that may not allow the TV to receive IP-address.
• 📶 Wi-Fi signal: check the signal level at the TV installation site. If the indicator on the router flashes yellow, the problem is the coverage. TV 4S and older critically, the signal level was not lower than 70% (can be checked through the Settings menu) → Wi-Fi).
• 🔧 Provider settings: some operators (for example, Rostelecom) block the connection of new devices without binding to the Internet MAC-Check with the support.
• 🔄 Firmware updates: If the TV hasn't been updated in a long time, some network protocols may not work properly. → On TV. → Updating the system.

If you connect your TV via an Ethernet cable, make sure that:

• 🔗 Cat Cat Cat Cat Cat Cat Category Cable is used 5e or higher (for speeds above 100 Mbit/s).
• 🔌 The port on the router works (try to connect another device to it, for example, a laptop).
• 🛠️ The router's settings are not disabled DHCP for wired connections (found in some TP-Link models).

2. Wi-Fi connection: step-by-step instructions for all Xiaomi models

Most users opt for wireless connectivity because of convenience.The Wi-Fi setup process on Xiaomi TVs is unified, but there are nuances for different versions MIUI TV. Let’s take a look at a universal algorithm:

Step 1: Open the settings menu by pressing the Settings button on the remote. In older models (e.g. Mi). TV (3) the path may be different: Menu → Settings → Network.

Step 2: Select a Wi-Fi partition (or Wireless Network) and the TV will start scanning the available networks if your network is not displayed:

• 🔍 Make sure the router doesn’t hide it. SSID (name).
• 📡 Check if the TV supports the frequency of your network (2.4GHz or 5GHz). TV 4 may not see 5GHz networks.
• 🔄 Restart the TV by holding the power button on the remote for 5 seconds.

Step 3: Select your network from the list and enter a password. There are two possible problems:

⚠️ Note: If the password contains Cyrillic characters or special characters (e.g, #, $), The TV may not recognize them. Try changing your password to Latin with numbers.

Step 4: After connecting the TV should receive IP-If there is an error "Receiving" IP-address...":

For Mi models TV Q1 and the newer "Quick Connection" function is available through QR-That's the code:

1. On your phone, open the Mi Home app (or any other generating app). QR-wifi).
2. In the TV Wi-Fi menu, select Connection QR-code.
3. Point the TV camera at QR-phonecode.

💡

If the TV constantly loses connection to Wi-Fi, try to fix static to it in the router settings. IP-This will prevent conflicts. DHCP.

3. Wireless Connection (Ethernet): When it's Better than Wi-Fi

Despite the convenience of Wi-Fi, wired connectivity has a number of advantages:

• 🚀 Stability: no interference from other devices (microwaves, neighbouring routers).
• 📈 Speed: over Cat cable 6 can be obtained before 1 Gbps (vs maximum) 300-400 Mbit/s on Wi-Fi 5 GHz).
• 🎮 Lesser ping: Critical for online gaming via cloud services (e.g. GeForce) NOW on Mi TV Stick).

To connect:

1. Connect the TV to the router with an Ethernet cable (not included in all models).
2. In the settings menu, select Wired Network (or Ethernet).
3. The TV will automatically receive the settings. If the connection is not established, check:

For Mi models TV P1 mi TV Q2 In Ethernet settings, you can have Traffic Priority, and if you turn it on, the TV will automatically reserve bandwidth for streaming, reducing delays.

4. Mobile Internet setting (USB-modem)

If you do not have home Internet, but have a smartphone with unlimited tariff, you can connect the TV through USB-modem or access point: This method is suitable for temporary use (for example, in the country), but has limitations:

• ⚠️ High latency (ping) – not suitable for online gaming.
• ⚠️ Speed limit by the operator (even with "unlimited" after 50-100 GB speed may fall).
• ⚠️ Fast battery discharge of a smartphone when used as a modem.

Connection through USB-modem (4G/5G):

1. Put it in. SIM-map USB-modem and connect it to the port USB 2.0 TV sets.
2. In the settings menu, select the Mobile Network (or USB-modem).
3. The TV will identify the modem as a network device. PIN-code SIM-map.

Connection through the smartphone access point:

1. On your smartphone, turn on modem modem (in the settings of Wi-Fi and network).
2. On the TV, connect to the created access point as a normal Wi-Fi network.
3. If the connection is unstable, reduce the number of connected devices to the access point.

⚠️ Note: Some Xiaomi models (e.g. Mi) TV 4A) supportive USB-Qualcomm modems, in which case only the Wi-Fi hotspot will help.

5. Solving Typical Internet Problems on Xiaomi TV

Even after a successful connection, users are faced with errors, and let's look at the most common ones and how to fix them.

Problem 1: The TV is connected to Wi-Fi, but the internet is not working.

• 🔧 Check the settings. DNS. Sometimes ISPs block access to certain services (like YouTube). DNS:
• 🔄 Reboot your router and TV at the same time (this will reset the cache) ARP-table).
• 🛡️ Turn it off. VPN on the TV (if it was tuned) in some regions VPN It may be in conflict with local DNS.

Problem 2: Slow Internet speed.

• 📡 If you use Wi-Fi, switch to 5GHz (if the router supports it). 2.4GHz speed is limited. ~50 Mbps.
• 🔌 For wired connection, check if the router is enabled with QoS (Quality of Service), which can limit the bandwidth for the TV.
• 📊 Go to Settings. → Network → Traffic statistics and check if background app updates (such as Netflix or Prime Video) consume the entire bandwidth.

Problem 3: The TV does not save the Wi-Fi settings after shutting down.

Problem 4: Mistake "I failed to get" IP-address".

• 🔧 Manually set static. IP-address in the TV Wi-Fi settings (e.g. 192.168.1.100 with 255.255.255.0 mask).
• 🔄 On the router, reduce the rental time DHCP 24 hours to 1 hour (this helps with address conflicts).
• 🛠️ If you use a dual-band router, disable the Smart Switch between 2.4 and 5 GHz function – it can knock the connection down.

6. Optimizing the network for streaming and gaming

If you use the TV to watch videos 4K Or in cloud gaming, standard network settings may not provide enough stability:

For streaming (Netflix, YouTube, IPTV):

• 📺 Enable in the Multicast router settings (for IPTV). On Mi. TV Path: Settings → Network → Additionally. → Turn on IGMP.
• 🔄 If the video is slowing down, limit the background download of updates. → Annexes → Auto Update Select "Only over Wi-Fi".
• 📊 Use the speed test in the TV menu (Settings) → Network → Speed test) to check the real bandwidth.

For cloud gaming (GeForce) NOW, Xbox Cloud Gaming):

• 🎮 Connect via Ethernet cable – the delay (ping) will be in 2-3 less than Wi-Fi.
• 🔌 On the router, turn on QoS and set the maximum priority for the router. MAC-TV address.
• 🛡️ Turn off the firewall on the router for the local network if the games are lagging.

For Mi models TV Q2 75" and Mi" TV P1 The network game mode feature is available, which reduces buffering by turning off background processes:

1. Go to Settings → Special Opportunities → Performance Mode.
2. Choose "Game Room."
3. Reboot the TV.

7. Network resets and extreme measures

If none of these things work, you might need to completely reset your network settings, or even reset your TV to factory settings, which is a last resort, but it often solves the problem of "hung" settings.

Reset only network settings:

1. Go to Settings. → Network → Additionally.
2. Select "Reset network settings."
3. Confirm the action. The TV will reboot.

Full reset of the TV (Hard Reset):

⚠️ Warning: This operation will delete all installed apps, accounts and personal settings. Before reset, write down your Mi Account login details and your Wi-Fi network settings.

1. Open Settings → About TV → Reset settings.
2. Enter. PIN-code (default 0000 or 1234).
3. Confirm the reset. It'll take 3-5 minutes.

After discharge:

• 🔄 First, connect your TV to the Internet via cable (if possible) – this will speed up the download of updates.
• 🔧 Do not restore settings from backup – this can bring back old errors.
• 📱 Install the latest updates through Settings → Updating the system.

💡

If the TV doesn’t connect to the network after the reset, the problem may be a hardware failure of the Wi-Fi module, in which case, contact the Xiaomi service center.

Frequently Asked Questions (FAQ)