How to close Fastboot on Xiaomi: from simple reboot to flashing

Fastboot mode on Xiaomi smartphones is a utility tool for firmware, unlocking the bootloader and diagnosing the device. However, many users face a situation where the phone “hangs” in this mode: the screen displays a hare in a hat-hunch (the Mi Bunny logo) and the inscription FASTBOOT, and the usual ways to turn off do not work. The reasons can be different: a failed update, a failure when unlocking the bootloader, or even an accidental push of a combination of buttons.

In this article, we will discuss all the current ways to exit Fastboot on Xiaomi, Redmi and POCO devices, from basic forced reboot to flashing through the Mi Flash Tool. We will focus on the methods that save user data, and warn about the risks that can lead to a “brick” (complete failure) of the phone. If your device does not respond to buttons or connect to a PC, do not panic: in 90% of cases, the problem can be solved without contacting the service center.

Why is Xiaomi stuck in Fastboot mode?

Before we start resuscitating the phone, it's important to understand what caused the freeze. Here are the most common scenarios:

• 🔄 Interrupted software update - if the firmware through MIUI Updater or Fastboot was interrupted (battery is dead, shut down) USB-cable).
• 🔓 Unlocking bootloader Failures – Mi Unlock Tool errors or version mismatch MIUI Xiaomi requirements.
• 🛠️ Failure in custom firmware - installation of unofficial Recovery (TWRP) bug-in.
• 🎯 Accidental activation – simultaneous pressing of Volume down + Power on switch-off/on.
• 🔋 Critical battery discharge – if the phone is drained while working with Fastboot.

In most cases, Fastboot is not a brick, it is a regular mode, and exit from it is possible. Except for situations where the firmware or bootloader is damaged (for example, if you unblock it incorrectly), then you will need to flash through EDL (emergency mode).

Method 1: Forced reset (the simplest method)

If your phone is responsive to buttons, the first thing you should do is try a hard rebuke, which works 70 percent of the time and doesn't require a PC connection.

1. Press the power button for 15-20 seconds (sometimes it takes up to 30 seconds).
2. If the screen is gone, but turned on again in Fastboot - repeat the action, holding Power + Volume up.
3. On some models (POCO F3, Redmi Note 10 Pro) the combination Power + Volume up + Loudness down (hold 10-15 seconds) helps.

If the phone vibrates but doesn’t leave the Fastboot, try plugging it into a charger for 10 to 15 minutes and then try again.

💡

On non-removable battery devices (such as the Xiaomi 12T), the hard rebuke may not work the first time. Repeat the attempt 3-4 times at 10 seconds intervals.

Method 2: Exit through the Recovery Menu

If forced reboot doesn't work, try recovering and rebooting from there, which is safe and doesn't cause data loss.

1. Turn off the phone (hold power until vibration).
2. Press Power + Volume up until the Mi logo appears.
3. In the Recovery menu, select Reboot → Reboot to System (use volume buttons for navigation, Power to confirm).

If Recovery shows a No command error or a menu in Chinese, it means that the custom recovery (TWRP) is installed.

1. Select Advanced → Reboot to Bootloader.
2. Then try again to go to Recovery and execute the rebukes in the system.

Method 3: Fastboot commands via PC (for power users)

If the phone is detected by the computer in Fastboot mode, you can send a command to restart via ADB/Fastboot. This method requires installed drivers and minimal knowledge of working with the command line.

What you need:

• 🖥️ Windows computer (or Mac/Linux fixed ADB).
• 🔌 Original. USB-cable (preferably from the set).
• 📥 Google's Platform Tools (download and unpack).

Step-by-step:

1. Connect your phone to your PC in Fastboot mode.
2. Open the command prompt (cmd) in the folder with Platform Tools.
3. Enter the command to check the connection: fastboot devices If the device is determined (the serial number will appear), run the reboot: fastboot reboot
4. If the phone doesn’t respond, try an alternative command: fastboot continue (works on some POCO models).

If the commands don't work, you might need to unlock the bootloader or flash it over, and then move on to the next method.

Method 4: Flash through the Mi Flash Tool (if the phone doesn't boot)

If previous methods didn't work, the firmware was likely damaged, and then a full flashing through the official Mi Flash Tool will help, which erases all data on the phone, including photos and apps, so use it only as a last resort.

Preparation:

• 📥 Download the official firmware for your model (choose the Fastboot version).
• 🖥️ Install the Mi Flash Tool.
• 🔓 Unlock the bootloader (if not unlocked) requires a tied Mi Account account and a wait of 7-15 days (Xiaomi rules).

Firmware process:

1. Unpack the downloaded firmware in a folder without Cyrillic symbols.
2. Open the Mi Flash Tool, press Select and point the path to the firmware folder.
3. Connect your phone in Fastboot mode (should be determined as to how to use it) COM-port).
4. Select the firmware method: Clean all – complete cleaning (recommended in case of failures). Clean all and lock – cleaning + lock the bootloader (if you need to return the phone to the “factory” state).

Flash

Once the firmware is in place, the phone will automatically restart. The first run can take up to 15 minutes - don't interrupt the process!

💡

If the Mi Flash Tool is an anti-rollback error, you are trying to flash an older version of MIUI than the one you installed, in which case you need to download the firmware of the same or newer version.

Method 5: Emergency EDL mode (if Fastboot doesn't work)

If the phone does not respond to buttons or Fastboot commands, the last option remains – firmware through the phone. EDL-Emergency Download Mode: This method requires special equipment (EDL-cable or testpoint, and used in service centers. EDL without experience can lead to a complete brik of the device!

When you need an EDL:

• 🚨 The phone doesn’t even turn on in Fastboot.
• 🔧 The Mi Flash Tool is running in error.
• 🔋 The device is not defined by a computer.

To run through the EDL, you will need:

1. Download firmware in.mbn format (for Qualcomm chips).
2. Use the QFil or Mi Flash Pro utility.
3. Connect your phone in EDL mode (via testpoint or special cable).

⚠️ Attention: Firmware through EDL Xiaomi (for new models) can be blocked without authorization IMEI And make your phone unusable for calls. If you're not sure what you're doing, call the service center.

Table: Compatibility of methods with Xiaomi models

Frequent Mistakes and How to Avoid Them

When using Fastboot, users often make mistakes that make the problem worse, and the most common ones are:

• 🔌 Use of unoriginal cables -- cheap cables don't have to transmit data, only charge. Always use a cable from the kit.
• 🔋 Firmware on low battery power - if the charge level is below 30%, the process may interrupt%.
• 📥 Downloading firmware from unofficial sources can lead to the installation of corrupted software or viruses.
• 🔓 Attempting to unlock the bootloader without waiting – Xiaomi requires an account and a wait (from 7 days.

⚠️ Warning: If the phone doesn't turn on after you've run through the Mi Flash Tool, don't try to repeat the process several times in a row. This can cause hardware damage to the flash memory. Let the device cool for 10-15 minutes and try again.

FAQ: Answers to popular questions