How to turn on Xiaomi Redmi Note 10S: all working methods and solving typical problems

Xiaomi Redmi Note 10S is a popular model with a reliable hardware platform, but even it sometimes refuses to turn on. The reasons can be different from the banal discharge of the battery to software failures after the MIUI update. In this article, we will discuss all possible ways to turn on the device, including forced reboot, charging in a turned off state and recovery through Fastboot. Particular attention will be paid to typical errors, for example, when the phone vibrates but the screen remains black, or when the Redmi logo lights up, but the boot does not go further.

If your Redmi Note 10S doesn’t respond to the power button, don’t rush to the service center. In 80% of cases, you can solve the problem yourself by following our instructions. We will also explain how to distinguish hardware failure (for example, a battery or motherboard malfunction) from software failure, which can be fixed without disassembling the device. For convenience, each method is accompanied by step-by-step screenshots (where possible) and video instructions.

1. Standard turn on: what to do if the phone does not respond to the power button

Start with the simplest, check if the battery is running out. Even if you're sure you charged the phone the day before, deep discharge can block the onset. Connect the Redmi Note 10S to the original charger (or Quick Charge 3.0 enabled) and wait at least 20 to 30 minutes. The charging indicator (if any) should light up in 5 to 10 minutes.

If the phone is still not activated after charging:

• 🔌 Try another charger or cable (especially if you use non-original accessories).
• 🔋 Connect your smartphone to a higher current power source (such as a laptop charger or power bank charger).
• 🔄 Hold the power button for 10-15 seconds – sometimes it helps to wake the device up after deep sleep.
• 📱 If the screen flashes or a logo appears MI, but the boot is interrupted – move to the next section (forced reboot).

Important: If the phone vibrates when charging is connected but does not turn on, this may indicate damage to the USB-C connector or power controller, in which case, try wireless charging (if supported) or contact the service.

2. Forced reset: when the phone is stuck on startup the logo

If the Redmi Note 10S turns on but gets stuck on the MI or Redmi logo, or the screen stays black after vibrating, a forced restart is required, which also helps if the phone doesn't respond to touches after a MIUI update or custom firmware installation.

Instructions:

1. Hold the Power + Volume button up at the same time for 10-15 seconds.
2. Release the buttons when the Mi logo appears or the screen goes out.
3. Wait 1-2 minutes – the phone should restart normally.

If the combination does not work, try an alternative method:

• 🔄 Keep your food on. + Volume down (this can trigger Fastboot mode).
• 📱 If you have a screen with a hare in the hat (Recovery mode), select Reboot. → Reboot to System.

Make sure the battery is at least 10 times charged%|

Turn off all cables (charging, headphones) |

Press and hold the buttons strictly at the same time |

If it doesn't work, repeat it in 30 seconds.-->

⚠️ Note: If the phone freezes on the logo again after a forced reboot, this may indicate damage to the system files).

3. Enabled through the charger: what to do if the phone is discharged to zero

The Redmi Note 10S battery (5,000 mAh) can run out of power to the point where even the charging indicator won’t light up, in which case a standard outlet connection won’t help – you’ll need to wake up the power controller.

Solutions:

If the charging indicator has not caught fire:

• 🔋 Try blowing the connector. USB-C compressed air (dust or debris may block contact).
• 🔌 Connect the charger to another outlet (possibly a problem with the power source).
• 📱 Leave your phone on charge for 1-2 hours – sometimes the controller does not wake up immediately.

💡

If after a long charge the phone turned on, but immediately turned off, check the battery status in the Settings → Battery menu. If the capacity drops to 0% in a few minutes, the battery needs to be replaced.

4.Recovery Mode: Reset settings if the phone doesn't boot

If the Redmi Note 10S is turned on but does not load beyond the logo, or a "No command" error appears, resetting via Recovery mode will help.This method is also relevant if you have forgotten your pattern lock or password.

How to log in to Recovery:

1. Turn off the phone (if it is on, hold the power until vibration).
2. Keep Power + Volume up until the Mi logo appears.
3. Release the buttons when the menu with the hare in the hat appears.

In the Recovery menu (management is carried out by volume and power buttons):

• 🔄 Choose Reboot. → Reboot to System (Reboot in Normal Mode).
• 🧹 If it doesn’t work, choose Wipe Data. → Wipe All Data (full reset) Warning: this will delete all data!
• 📱 After reset, select Reboot to System.

⚠️ Note: Recovery removes all user data, including photos, contacts and apps. If you have Mi Cloud enabled, some of the data can be restored after you log in to your account.

5. Fastboot flashing: if the phone is not turned on due to a software failure

If all previous methods have failed and the phone only reacts to the PC connection (vibrates or is defined as Qualcomm) HS-USB QDLoader 9008, you need to flash it through Fastboot, which is also relevant if you see the error "This" MIUI version cannot be installed on this device".

What you need:

• 🖥️ Windows computer 10/11 (recommended).
• 🔌 The original cable. USB-C.
• 📥 Firmware for Redmi Note 10S (Rosemary codename from en.miui.com.
• 🛠️ The Mi Flash Tool (you can download it here).

Step-by-step:

1. Install Qualcomm and Mi Flash Tool drivers on PC.
2. Turn off the phone, then hold Power + Volume down to log into the Fastboot.
3. Connect your smartphone to your PC. Android Bootloader Interface should appear in the Device Manager.
4. Launch the Mi Flash Tool, select the downloaded firmware (.tgz format) and press Refresh.
5. Press Flash and wait for the process to end (5-10 minutes).

Once the firmware is in place, the phone will automatically restart. The first run can take up to 15 minutes - don't interrupt the process!

💡

Fastboot flashing is an extreme method that should only be used if other methods have not worked. Incorrectly selected firmware or an interrupted process can lead to the "bricking" of the device.

6.Diagnostics of hardware problems: when to carry in the service

If none of these methods worked, the problem could be hardware, and here are the signs that the iron is malfunctioning:

• 🔋 The phone does not respond to charging (no indication, no warm connector).
• 💥 There is a smell of burning or corrosion on the board (after moisture enters).
• 🔊 Phone vibrates, but screen remains black (possibly the plume dump of the display).
• 🔄 Cyclical reboot (infinite reboot) without booting the system.

Typical hardware faults of Redmi Note 10S:

If you suspect a hardware malfunction, don't try to disassemble the phone yourself, which could cause more damage. Contact a Xiaomi authorized service center or a trusted workshop before visiting:

• 📋 Write it down. IMEI phone number (can be found on a box or check).
• 🔄 Try backing up data via Fastboot (if the phone is determined by PC).
• 💰 Check the cost of diagnosis (in some services it is free).

7.Preventing Turn-on Problems: How to Avoid Repeated Failures

To ensure that Redmi Note 10S does not refuse to turn on in the future, follow these recommendations:

• 🔋 Avoid deep battery discharge (charge your phone at 10-15%).
• 📱 Update regularly MIUI through settings → Update of the PO.
• 🛡️ Do not install custom firmware without a backup.
• 💧 Avoid getting moisture into the connector USB-C and dynamics.
• 🔄 Once a month, perform a soft reset (reboot through the food menu).

Also useful:

• 🔄 Include automatic optimization in Settings → Special facilities → Optimization of the system.
• 📥 Install Xiaomi’s Security app to monitor battery status.
• 🔋 Calibrate the battery: discharge the phone to 0%, then charge to 100% without interruption.

💡

If you experience frequent freezes, turn on the developer mode and turn off window animation in Settings → About Phone → MIUI version (7 times click on the version, then return to Additional → For Developers).

FAQ: Frequent questions about the inclusion of Xiaomi Redmi Note 10S