How to turn on Xiaomi Redmi Note 9 Pro: all ways to launch a smartphone

Xiaomi Redmi Note 9 Pro is one of the most popular smartphones in the budget segment, but even with it sometimes there are problems. The most common situation: the phone does not turn on after discharging, updating or mechanical impact. In this article, we will discuss all possible ways to turn on the Redmi Note 9 Pro, from basic to emergency, and also tell you what to do if the smartphone does not respond to the power button.

It's important to understand that the reasons for not turning on can be from simple battery drains to hardware breakdowns, so we structured the instructions so that you can quickly find a solution to your situation, starting with the simplest methods and gradually moving on to more complex ones.

1. Standard on: Power button

If your Redmi Note 9 Pro is fully functional and is simply off, you can turn it on in the standard way.

• 🔋 Make sure the smartphone is charged (the on-screen indicator or LED should burn when charging is connected).
• 🔘 Press the power button (located on the right side edge) on 2-3 seconds.
• 📱 Wait for the Redmi logo to appear – this is a signal that the device starts loading.

If nothing happens after pressing the power button, check:

• 🔌 Is the charging cable connected (sometimes the smartphone does not turn on due to a critically low charge).
• 🔊 Does the case block access to the button (especially important for thick or magnetic cases).
• 💧 Is there any moisture in the charging socket (if the phone has recently been in contact with water).

⚠️ Attention: If the screen flashes after pressing the power button, but the smartphone does not load, this may indicate damage to the firmware.

2. Forced reset (Hard Reset)

If the Redmi Note 9 Pro is stuck on the logo, doesn't respond to touches or the power button, try a forced reboot. This method doesn't delete data, it just restarts the system.

For this:

1. Press the power button and increase the volume at the same time.
2. Hold them for at least 10-15 seconds until the screen goes out and the Redmi logo lights up again.
3. Release the buttons and wait for the full load (can take up to 2-3 minutes).

This method helps in 80% of cases of hanging caused by:

• 🔄 Failure to update software.
• 🎮 System overload due to heavy games or applications.
• 📱 Background Process Conflict.

Make sure the battery charge is > 10%|

Turn off the charger (if connected)|

Check if the volume button is accidentally pressed |

Wait 30 seconds after hanging before restarting-->

⚠️ Warning: Don't confuse forced reset with factory reset! The first method is data-safe, the second method removes everything from the phone. Read more about reset in the Recovery Mode section.

Initiation via charger

If the Redmi Note 9 Pro battery is completely drained, the smartphone may not respond to the power button even after connecting to the network.

1. Connect the original cable and power supply (preferably 18W or 33W).
2. Leave the phone to charge for at least 20-30 minutes (even if the indicator is not on).
3. Try turning it on with the power button.

If the charging indicator does not light up:

• 🔌 Try another cable or power supply (possibly a problem in charging).
• 🔍 Check the connector. USB-C for debris or oxidation (clean carefully with a toothpick).
• 🔋 Connect your phone to another power source (computer, power bank).

💡

If the phone doesn’t respond to charging, try holding the power button clamped. 20-30 Sometimes it helps to wake up the power controller.

4. Enable via Recovery Mode (if the phone doesn't boot)

If the Redmi Note 9 Pro is turned on but not loaded beyond the Mi logo or is cyclically rebooted, the firmware may be damaged.

To get into the recovery menu:

1. Turn off the phone (if it is turned on, perform a forced reboot).
2. Press the power button and increase the volume at the same time.
3. Hold them until the Mi Recovery logo appears (usually 5-10 seconds).

In the Recovery menu, you can:

• 🔄 Reboot the system (Reboot).
• 📁 Install the update with SD-Maps (Apply update from) SD card).
• 🧹 Reset the settings to factory (Wipe data – more below).

⚠️ Note: If the Recovery menu displays characters or incorrect characters, it means that the firmware is damaged at the bootloader level).

5. Reset to factory settings (Wipe Data)

If the Redmi Note 9 Pro is turned on but not loaded due to a software failure, the last way to do it without a PC connection is to reset via Recovery. This procedure will delete all data (photos, apps, accounts), so use it only as a last resort.

Instructions:

1. Go to Recovery Mode (as described in the previous section).
2. Select Wipe Data (use volume buttons for navigation, power button for confirmation).
3. Confirm the reset by Confirm selection.
4. After completion, select Reboot.

After the reset, the phone will turn on in the "out of the box" state.

• 📱 Complete the initial setup (language selection, Wi-Fi connection).
• 🔑 Sign in to your Mi Account if you have previously linked it.
• ☁️ Restore data from a backup (if it was created in Mi Cloud).

💡

Resetting to factory settings only removes user data. The firmware and Android version remain the same. If the problem was in the system files, reset may not help - you will need to flash it.

6. Enable via Fastboot (for power users)

If the Redmi Note 9 Pro doesn’t even turn on in Recovery Mode, but it reacts to a PC connection (defined as Qualcomm HS-USB QDLoader 9008 or the like), you can try flashing it through Fastboot.

• 🖥️ Computers with Qualcomm drivers installed and ADB.
• 📂 Firmware for your model (you can download on the official website of Xiaomi).
• 🔧 Mi Flash Tool or Fastboot Enhance.

Instructions:

1. Turn off the phone.
2. Press the power + volume buttons before the screen with a hare in a fastboot mode appears.
3. Connect the phone to the PC.
4. Start the Mi Flash Tool, select the firmware and press Flash.

After successful firmware, the phone will restart automatically. If the process stops, try again or check:

• 🔌 Quality. USB-cable (it is better to use the original cable).
• 🔋 Battery level (must be at least 30%).
• 📋 Compatibility of firmware with your model (Redmi Note 9 Pro has several modifications: joyeuse, curtana, excalibur).

💡

Before you run through Fastboot, check the phone serial number in the Fastboot menu (shown at the bottom of the screen) and it should match the number on the box or in the settings (if the phone was previously turned on), which will help avoid firmware on the wrong model.

7. Emergency activation via EDL mode (for critical cases)

If the Redmi Note 9 Pro doesn't turn on at all (it doesn't respond to buttons, it's not defined in Fastboot), the last chance is EDL (Emergency Download Mode) mode, which allows you to flash your phone even with a dead bootloader, but requires:

• 🔧 Specialist EDL-cable (or closing the test point on the board).
• 🖥️ Mi Flash Tool or QFil.
• 📄 Firmware in.mbn format for your model.

Instructions (for experienced users):

1. Turn off the phone from all power sources.
2. Connect. EDL-cable (or close the test point if you disassemble the phone).
3. The phone must be identified in Device Manager as Qualcomm HS-USB QDLoader 9008.
4. Run the firmware through the Mi Flash Tool (select Clean All mode).

⚠️ Attention: Regime EDL can lock the phone if it was linked to the Mi Account with the Find Device function enabled, in which case, after the firmware, you will need to enter the login and password from the account to which the phone was associated.

8. Hardware malfunctions: when to carry in the service

If none of these methods worked, the problem is likely hardware.

Average cost of repair Redmi Note 9 Pro in service centers (2026):

• 🔋 Battery replacement: 1,500–2,500 ₽.
• 📱 Display replacement: 3,000–6,000 ₽ (depending on the originality of the spare part).
• 🔧 Repair board (seeding of elements): from 2 000 ₽.

If the phone is warranty, do not disassemble it yourself - this will cancel the warranty obligations. mi.com/ru/service.

FAQ: Frequent questions about the inclusion of the Redmi Note 9 Pro