How to turn on Xiaomi Poco smartphone: from basic launch to emergency methods

Introduction: Why Xiaomi Poco can't be turned on?

Xiaomi Poco smartphones are known for their reliability, but even they sometimes refuse to start. The reasons can vary from a completely discharged battery to software failures after an upgrade. Statistics from service centers show that in 60% of cases the problem is solved without repair - it is enough to perform a forced reboot or charge correctly.

This article covers all possible scenarios, from standard onset to recovery from a brick, and we'll figure out what to do if the screen is black, the phone vibrates but doesn't turn on, or the device is getting stuck on the POCO logo. It's important to understand that the actions depend on the specific situation - there is no universal solution.

Before proceeding with the instructions, check the obvious: does not leave the charging cable, is not damaged USB-C connector, and is not accidentally pressed the power button (on some models Poco F3 or Poco X3 Pro it can stick due to dust).

Method 1: Standard inclusion of Xiaomi Poco

If the phone is turned off normally (for example, after an update or on your command), it is enough to turn on:

1. Connect the charger (even if the battery is not discharged – this will eliminate power problems).
2. Press the Power button (usually located on the right) for 3-5 seconds until the POCO logo appears.
3. Release the button and wait for the system to boot up fully (it can take up to 1 minute).

On models with a power button fingerprint scanner (like the Poco X4 Pro 5G), don't press too hard -- just press it lightly enough. If the phone doesn't respond, move on to the next method.

The charging cable is serviceable and tightly inserted

The power adapter delivers at least 10W (5V/2A)

The Power button is not stuck and pressed clearly

The screen has no physical damage.-->

If a red light appears after pressing the power button (on some models), this signals a critically low battery charge - charging is required for at least 10-15 minutes before turning on.

Method 2: Forced Reset (Hard Reset)

When the Xiaomi Poco smartphone freezes on the logo, does not respond to presses, or the screen remains black despite charging connections, hardware reset will help, which does not delete data, but only restarts the system.

Instructions for most models (Poco F5, Poco M6 Pro, Poco C55, etc.):

1. Press the Power + Volume Up buttons at the same time.
2. Hold them for 10-15 seconds until the screen goes out and reboots.
3. After the POCO logo appears, release the buttons.

Some devices (like the Poco X3 NFC) may require a Power + Volume Down combination. If it didn't work the first time, try again by holding the buttons longer.

⚠️ Warning: Don't confuse forced reboot with factory reset (Wipe Data), the first method is data-safe, the second one removes everything from the phone.

Method 3: Enable via charger (at discharge)

If the Xiaomi Poco doesn't turn on due to full discharge, the standard charging connection may not work right away.The lithium-type battery requires minimal voltage to start charging. Here's what to do:

• 🔌 Use the original adapter (or Quick Charge support) 3.0/4.0)."Left-handed charging may not give enough current.
• ⏳ Leave the phone charging for at least 30 minutes before trying to turn on.The charging indicator (if any) should catch fire.
• 🔄 If the indicator doesn’t burn after 30 minutes, try another charger or cable (the problem may be in the damaged wire).
• 🔋 On models with removable battery (for example, Poco) M2) You can remove the battery for 10 seconds, then insert it back and connect the charging.

To speed up the process, connect your phone to charge when it's off, so the power goes directly to the battery, not to the system. If the charging indicator flashes red, this is a sign of a deep discharge, it will take 1-2 hours to restore the minimum charge.

Poco F5/F5 Pro

Poco X5/X5 Pro

Poco M6 Pro/M6

Poco C55/C51

Another model-->

Method 4: Recovery through Recovery Mode

If the smartphone is turned on but constantly restarts or hangs on the logo, you will need to enter Recovery Mode, a method that allows you to clear the cache or reset to factory settings.

Instructions for entering Recovery:

1. Turn off the phone (if it is turned on, perform a forced reboot).
2. Press Power + Volume Up and hold until the Android menu appears.
3. Use volume buttons for navigation and Power to select a point.

From the Recovery menu, select:

• Wipe cache partition – cache cleaning (does not delete data).
• Reboot system now – reboot after cleaning.

If the problem persists, you may need Wipe data/factory reset, which will delete all data, including photos and apps, and try connecting your phone to your PC for backup.

💡

If the Recovery menu is in Chinese, select the item with the characters "cleaning the cache" or "" (rebooting).

Method 5: Enable via Fastboot (for power users)

If the phone doesn't boot even to Recovery, it's Fastboot mode, which allows you to reflash the device over your PC, but requires ADB and Fastboot skills.

Step-by-step:

1. Install Platform Tools on your PC (from Google).
2. Turn off your phone and press Power + Volume Down until the screen with Fastboot Mode appears.
3. Connect your phone to your PC via USB.
4. In the command line (Windows: Win + R → cmd), type: fastboot devices If the device is determined, continue. If not, check the drivers.
5. To reboot, type: fastboot reboot

If the phone doesn't respond to commands, you may need to flash it through the Mi Flash Tool, which is a risky process, because if you make a mistake, the device can turn into a brick.

⚠️ Note: Using Fastboot on a blocked bootloader will lead to an error. Unlocking the bootloader erases all data and requires binding to a Mi Account account.

What do you do if nothing helps?

If all of the above methods fail, the problem may be hardware:

• 🔋 Battery malfunction - bloating, short circuit (visually check if the battery is swelling).
• 🔌 Damage to the motherboard – often after falling or getting moisture.
• 📱 Display plume dump – the screen does not turn on, but the phone vibrates and makes sounds.
• ⚡ Power controller failure – phone does not respond to charging and buttons.

In these cases, self-repair is not recommended. Contact an authorized Xiaomi service center - they have diagnostic equipment and original spare parts. The average cost of diagnosis is 500-1000 rubles.

Before the service visit:

1. Check if the warranty is maintained (check in the Mi Service IMEI app).
2. Take a picture of the serial number (under the lid or on the box).
3. If your phone is turned on at least once, make a backup through the Mi Cloud.

💡

If the phone was in water, DO NOT TRY TO ON IT! Immediately remove the battery (if removable) and take it to the service. Turning on the wet device causes short circuit and permanent damage.

FAQ: Frequent questions about Xiaomi Poco inclusion