How to remove Fastboot on Xiaomi Redmi 8: the complete guide

Owners of Xiaomi smartphones often face a situation when after the next turn on the device does not load into the usual interface, but shows a screen with a picture of a hare repairing an android. This is the Fastboot mode, which is designed for low-level firmware of the device, but in everyday life it becomes an obstacle for the phone. Don’t panic, since in most cases the system is not damaged, and the phone simply “stuck” in this state due to a software error or accidental button pressing.

You can remove Fastboot on Redmi 8 in a number of ways, from just waiting to flashing it, and it's important to understand that the way you solve the problem dictates how you get it. If it was a single failure, simple button manipulation will help, but if the phone gets into this mode constantly after each reboot, you'll need to have a deeper software intervention.

In this article, we will take a look at all available methods for exiting bootloader mode. We will look at both the standard methods that are safe for user data, and more radical measures that require a connection to a computer. On Redmi 8, Fastboot mode is often blocked by a hardware volume button that can be clamped by a case or dust in the connector. Carefully follow the instructions to bring the smartphone back to life without losing important files.

What is Fastboot Mode and Why It Engaged

Fastboot is a special diagnostic protocol built into the Android operating system. It allows you to perform low-level operations with the device, such as unlocking the bootloader, installing custom recaps or completely flashing the system. Redmi 8 can be accessed by holding the volume down and power button simultaneously. Usually users do this by accident when the phone is lying in a tight case or in a pocket with keys.

But there are software reasons for activation: Damage to system files, a failed firmware update, or conflict of newly installed applications can force the phone to leave the Fastboot at every start, and it can also be caused by a physical malfunction of the volume button plume or moisture entering the body, which causes the contacts to close.

Visually, the mode is determined by a black screen with the Mi Bunny logo and the orange FASTBOOT label. The bottom of the screen often displays the device's serial number and USB connection status. While the phone is in this state, it cannot perform its usual functions of calling, receiving messages or running applications.

Ways to exit with buttons

The easiest and safest way to remove Fastboot on Redmi 8 is to use hardware buttons, which does not require a connection to a computer and does not affect the safety of your data. It is effective in 90% of cases if the problem is caused by accidental pressing or a short-term software failure.

To do this, you need to press the power button. Hold it long enough, about 10-15 At this point, the device will be forced to restart, and if the phone is again showing the hare after the vibration, repeat the procedure, but this time make sure that the volume button is not clamped.

Sometimes you need a combination of actions. Try to press the power buttons and turn up the volume at the same time. Hold them for about 20 seconds. This method often helps to break through the freeze if the standard reboot doesn't work. The main thing is to keep the buttons on until the Mi logo appears.

⚠️ Attention: If you reboot your phone and it goes back to Fastboot, it's more of a random problem. Don't keep rebooting the device indefinitely, it can drain your battery.

Use of PC and ADB utility

If the buttons don't work, you can use your computer, and you need to have Xiaomi drivers installed on your PC and the ADB (Android Debug Bridge) utility, which allows you to send a software command to exit bootloader mode, ignoring the physical state of the buttons.

First, connect your phone to your computer through the original USB-Make sure that the Windows Device Manager in the Android Devices or LibUSB section shows the connected device. If the drivers are not installed, download them from the official website or through the Mi program. PC Suite.

Open the command line in the ADB tool folder and enter a command to reboot. This action will force the normal boot process of the operating system, bypassing debugging mode.

adb reboot

If the adb reboot command fails and the console says that the device is not found, try the command to reboot to normal mode specific to fastboot:

fastboot reboot

After you enter the command, the phone screen should go out and after a few seconds the Mi logo should appear. This method is especially useful if the power button on the device itself is physically faulty or falters.

💡

Use only original or certified USB-Cheap charging cables often don’t have data lines, which means your computer won’t see your phone in Fastboot mode.

Resetting settings via Recovery Mode

In cases where a software failure blocks normal booting, settings may need to be reset.Recovery mode on Xiaomi allows you to perform a cleanup of user data, which often eliminates conflicting files causing the departure in Fastboot.

To enter Recovery on a phone that is turned off, press both the power button and the volume button. Hold them until the logo appears, then release the power, but keep the volume up until the menu appears. Navigation is done with volume buttons, and the power button selects.

From the menu, select Wipe Data, then Wipe All Data. Confirm action. Once you've completed the process, select Reboot → Reboot to System. The phone will reboot as new.

Table: Comparison of exit methods

To make it easier for you to choose the right way to solve the problem, we have systematized the basic methods in the table below.

Firmware via Mi Flash Tool

If none of the above has worked, and Redmi 8 continues to cycle off to Fastboot, the operating system itself is likely damaged, in which case the only solution is to completely reflash the device using the official Mi Flash Tool utility.

You will need to download the firmware image for your model (it is important to choose the correct version: Global, China, Russia) and unpack it on your computer. The phone must be connected in Fastboot mode. In Mi Flash, select the path to the firmware folder and press the Flash button.

The process can take anywhere from 5 to 15 minutes, during which time it is strictly forbidden to turn off the cable or interrupt the power of the computer, and after successful completion, the phone will automatically restart to the clean system.

💡

If Mi Flash is a firmware error, try replacing it. USB-cable or connect the device to another USB-port (preferably) USB 2.0) at the rear of the system unit.

Hardware causes and repairs

And there's some hardware issues, too, because the Redmi 8 has a volume button plume sticking, and even if the visual button is running normally, the contact can oxidize inside, locking the circuit all the time, so the phone will leave the Fastboot as soon as it leaves.

You can check this by gently pressing the volume button in different directions during the turn on, if the phone only loads at a certain position of the button, you need to change the plume, and the cause may be a bloated battery that presses on the board.

• 🔌 Check the charging connector for debris and oxides that can shorten contacts.
• 🔨 Carefully tap your phone with the edge of your hand (no bigotry) to shift possible dust inside the buttons.
• 🌡️ If the phone has recently fallen or got wet, the problem is almost certainly hardware – bring it to the service.

⚠️ Warning: If you don't have experience disassembling smartphones, don't try to open the case yourself.You may damage the plumes or break the tightness of the case, leading to more expensive repairs.

Frequently Asked Questions (FAQ)