How to Reset the Xiaomi Mi Robot Vacuum: All Ways (2026)

Xiaomi Mi Robot Vacuum is a smart device that can eventually malfunction: loses touch with the Mi Home app, builds a map incorrectly, ignores commands or stops turning on altogether. 80 percent of the time, factory resets solve these problems. But how do you do it right so you don't turn the vacuum cleaner into a brick?

In this article - all the current methods of resetting for Mi Robot Vacuum-Mop models (S5/S6/S7), Mi Robot Vacuum (1S/2C) and other, including hidden methods through ADB We'll take a look at the service menu:

• 🔄 Soft reset (without loss of card data)
• ⚙️ Hard reset (complete erasure of settings)
• 📱 Reset via Mi Home and Mi Home Lite
• ⚠️ What to do if the vacuum cleaner does not respond to the discharge

You will also learn how to reconnect with the vacuum cleaner after reset if it does not connect to Wi-Fi or gives an error “Device not found”.

1.When you need to reset the Xiaomi robot vacuum cleaner

Reset the vacuum cleaner settings is not at the first mistake, but in specific cases:

• 🗺️ The vacuum cleaner does not save a map of the room or builds it with distortions (for example, duplicates rooms).
• 📵 The device does not connect to Wi-Fi, although the password is correct and the router works.
• 🔄 After updating the firmware vacuum cleaner hovers on the logo or cyclically reboots.
• 🚫 Mi Home app shows error "Device disabled" or "Can't contact robot".
• 🔋 The battery discharges in 10 minutes, although it used to last longer (sometimes the reset calibrates the power controller).

❌ Do not discard the vacuum cleaner if:

• 🛠️ He just doesn't drive because of clogged brushes or wheels (clean them up).
• 🔊 Squeaking and flashing red is a sensor error, not a software failure (see the error section).
• 📶 Problems connecting to only one router (try another).

2.Soft reset (without deleting maps and settings)

This method reboots the vacuum cleaner system without affecting stored maps and cleaning settings, suitable if the device has become braking or does not respond to commands.

Instructions:

1. Make sure the vacuum cleaner is on (the indicator is white or blue).
2. Press the home button (🏠) and the on/off button at the same time.
3. Hold for 10-15 seconds until you hear a beep and see the indicator blink.
4. Release the buttons and the vacuum cleaner will reboot.

🔹 Signs of a successful soft reset:

• 🔄 The robot emits a long beep.
• 💡 The indicator flashes blue 2-3 times.
• 📱 In the Mi Home app, the device status changes to "Reboot".

💡

If after a soft discharge the vacuum cleaner still brakes, try to clean the cache in the Mi Home app: go to Profile → Settings → Clear the cache.

3. Hard reset (complete erasure of data)

This method removes all settings, including:

• 🗺️ Preserved maps of premises.
• 📶 Wi-Fi connection data.
• ⚙️ Individual cleaning parameters (power, zones, schedule).

Use it if the soft reset didn’t help or you’re selling a vacuum cleaner.

Step-by-step:

1. Turn off the vacuum cleaner (press the On/Off button for 3 seconds).
2. Press the buttons at the same time (🏠) and Spot Cleaning (🎯).
3. Hold for 15-20 seconds until you hear a double squeak.
4. Release the buttons and the indicator will start flashing orange.
5. Wait for the reboot (1-2 minutes).

Take a picture of the current maps of the premises in the application|Write down your Wi-Fi password.|Disconnect the vacuum cleaner from the charging station|Make sure the battery is charged >30%-->

⚠️ Warning: After a hard reset, the vacuum cleaner won't automatically connect to Wi-Fi. You'll have to reset:

1. Add it to the Mi Home app as a new device.
2. Set up maps of the premises from scratch.
3. Set a cleaning schedule.

4.Reset via the Mi Home app

If you have a vacuum cleaner connected to an application, you can reset the settings remotely. This method works for Mi Robot Vacuum-Mop P models, S7, S7 Pro and others with cloud management support.

How to reset:

1. Open Mi Home and select your vacuum cleaner.
2. Go to the Device Settings (⚙️) → General. → Resetting settings.
3. Confirm the action (it may be necessary to enter a password from your Mi Account).
4. Wait for the process to be completed (the vacuum cleaner will emit an audible signal).

🔹 Features:

• 🌐 It only works with a stable internet connection.
• ⏳ The process can take up to 5 minutes (don’t close the application!).
• 📵 If the vacuum cleaner is offline, the reset via the app will not work.

5. Reset via service menu (for power users)

Some Xiaomi Mi Robot Vacuum models, for example, S50, S51) have a hidden service menu available through ADB It's a risky method, and only use it if other methods have failed.

Method 1: Through a combination of buttons

1. Turn off the vacuum cleaner.
2. Hold it home (🏠) + Spot Cleaning (🎯) + On/off.
3. Hold for 30 seconds until the red light flashes.
4. Release the buttons - the vacuum cleaner will go into service mode.
5. To reset, press the on/off again for 5 seconds.

Method 2: Through ADB (wired-only)

If your vacuum cleaner has custom firmware (for example, Valetudo), you can reset the settings through the command:

adb shell


su




reset_factory

⚠️ Attention: Misuse of the right ADB If you're not sure, you can go to the service center.

6.What to do if the vacuum cleaner does not respond to the discharge

If after all the manipulations vacuum cleaner:

• 🔴 Not turned on (indicator not on).
• 🔄 Hanging on the Mi logo.
• 📵 No sounds when pressing buttons.

So the problem is deeper than a software failure.

🔧 If the vacuum cleaner does not respond at all:

1. Try to turn off the battery for 10 minutes (disassemble the case, disconnect the battery connector).
2. Connect to the charge another power supply (original, 20V/1.5A).
3. Contact the Xiaomi Service Center (if warranty is valid).

💡

If the vacuum cleaner doesn't turn on after the discharge, 90% of the time it's the fault of the discharged battery.+ minutes, even if the indicator is not lit. - Perhaps the protection against deep discharge will work.

7.How to restore the vacuum cleaner after discharge

After a hard discharge, the vacuum cleaner becomes clean, without settings or maps, to get it back to work.

Step 1 Connect to Wi-Fi

• 📱 Open Mi Home and click Add Device (+).
• 🔍 Select a Robot Vacuum from the list.
• 📶 Make sure the router is running at 2.4 GHz (5 GHz not supported!).
• 🔑 Enter your Wi-Fi password (use only Latin and numbers).

Step 2. Set up the map

• 🗺️ Run the vacuum cleaner in cleaning mode (Start cleaning in the application).
• 🏠 Wait for him to build a new map (it will take 1-2 full cleanings).
• 📏 Mark up rooms in the app: Map → Edit → Add a room.

Step 3: Restore the schedule

• ⏰ Go to the schedule. → Add.
• 📅 Choose the days and times of cleaning.
• 🔄 Set up cleaning areas (if necessary): Map → Zones. → Add.

⚠️ Warning: If the vacuum cleaner does not save the card after the discharge (resets after the switch is turned off), this may mean:

• 🔋 Flash memory malfunction (requires a replacement module).
• ⚡ Firmware failure (try to update the software manually).

8 Common errors after reset and their solutions

Even after a successful reset, problems can arise, and here are the most common ways to fix them:

🔍 How to Reset a Specific Mistake:

1. Press the On/Off button for 10 seconds, and this will reset the current error.
2. If the error occurs again, eliminate the cause (see table above).

📌 Tip: If the vacuum cleaner gives you Error 12 (fan motor problem), try it:

• 🧹 Clean the turbine of debris (remove the top cover).
• 🔧 Check the connection of wires to the motor.

FAQ: Frequent questions about resetting Xiaomi Mi Robot Vacuum