Resetting the scooter Xiaomi to factory settings: all ways and nuances

Reset Xiaomi scooter to factory settings may be necessary in a variety of situations: from selling the device to eliminating software failures. This procedure returns all parameters to their original state by removing tied accounts, speed settings, mileage data, and even restrictions set by the previous owner. However, not all users know that a full reset on Xiaomi scooters differs from a similar procedure on smartphones - there are its own nuances associated with the firmware, version. BLE-module and even the physical condition of the device.

In this article, we will analyze all the current ways of resetting for Xiaomi models. M365, Pro 1/2, Essential, 1S And others, both through the official Mi Home app and through the hardware buttons, and we'll focus on common errors that can turn a simple procedure into a headache, from the scooter to the reset phase to the loss of Bluetooth connectivity. You will also learn how to check whether the reset was really successful, and what to do if the scooter then stopped turning on.

When do I need to reset the Xiaomi scooter to factory settings?

Many users resort to resetting as a “last resort”, but there is actually a clear list of cases where this procedure is justified:

• 🔄 Resale of scooter – the new owner should be able to link the device to his Xiaomi account and customize it for himself.
• 🚨 Software failures – if the scooter arbitrarily brakes, does not respond to the on button or “glues” the display (on models with a screen).
• 🔒 Removing restrictions – the previous owner could set a speed limit or block certain features through the app.
• 📱 Connection problems – the scooter is not detected in Mi Home, permanently breaks the Bluetooth connection or requires a firmware update, but the update gets stuck".
• 🔋 Incorrect battery operation - if after replacing the battery, the scooter shows an incorrect charge level or quickly discharges.

It is important to understand that resetting will not help with hardware malfunctions: worn bearings, damaged control board or a failed controller. In such cases, repair is required, not a software reboot. It is also useless to reset if the scooter is physically locked (for example, through the Anti-Theft function in the application) – you will need to contact Xiaomi support to unlock.

Preparation for resetting: what to do in advance

Before you start resetting, follow a few mandatory steps to avoid typical problems such as losing contact with the scooter or not being able to complete the procedure.

⚠️ Note: If the scooter is linked to a Xiaomi account with Anti-Theft enabled, it may require the previous owner to enter the username/password after the reset. Make sure you have access to this data or turn off protection in advance in the application settings.

Preparation checklist:

Pay special attention to the level of battery charge. If the scooter discharges during reset, this can lead to damage to the firmware and the need to reflash the controller through specialized equipment — 50-70%, less 30%. Also make sure there are no Bluetooth interference sources nearby (e.g., running microwave ovens or other devices on frequency). 2.4 GHz).

If you drop the scooter before selling, untie it from your Mi Home account in advance:

1. Open the app and select your scooter.
2. Go to Device Settings → General → Delete the device.
3. Confirm the action (you may need to enter a password from your Xiaomi account).

This will save the buyer from having to enter your data after the reset.

Method 1: Reset via the official Mi Home app

The easiest and safest method is to use the branded Mi Home app, which is suitable for most Xiaomi models, including the one that is used by the company. M365, Pro 1/2, Essential and 1S. The main condition is that the scooter must connect to the application without errors.

Step-by-step:

1. Open Mi Home and select your scooter from the list of devices.
2. Go to Settings (⚙️) → General settings → Reset to factory.
3. Confirm the action, wait until the process is completed (usually takes a lot of time). 1-2 minute).
4. The scooter will automatically reboot, and then you can link it to a new account.

If there is no “Reset to factory” item on the menu, try updating the app to the latest version or check if this section is hidden behind additional settings (for example, in some versions of Mi Home you need to first click Additional).

After being dumped through Mi Home:

• 📱 Get rid of all accounts.
• 🔧 Returns standard settings of speed, energy saving and backlighting.
• 🔄 Resets mileage data and travel history.
• 🔋 Reset battery calibration (may temporarily show incorrect charge level).

💡

If the scooter does not turn on after reset, connect it to the charger on the 10-15 Sometimes the controller needs time to initialize after settings have been zeroed out.

Method 2: Hardware reset via buttons (for all models)

If the scooter doesn’t connect to the Mi Home or you prefer to do without the app, you can reset using physical buttons.This method works on all Xiaomi models, including old ones. M365 The new Pro 2.

Instructions:

1. Turn off the scooter (press the power button for 3 seconds).
2. Press the power button and the brake button (on the handle) at the same time.
3. Hold them down. 5-7 seconds until you hear a beep (or flash an indicator).
4. Release the buttons – the scooter will start the reset process (can flash red/blue).
5. Wait for the reboot (usually takes up to 1 minute).

On some models (e.g. Xiaomi) 1S) Instead of the brake button, you can use a headlamp button. If the combination doesn't work, try holding the power button only for a period of time. 10-15 Seconds – this can initiate a reset on old firmware.

⚠️ Attention: Scooters with firmware CFW (Custom) hardware reset can lead to "bricking" of the device. If you installed unofficial software, first return the stock firmware through DownG or ScooterHacking Utility.

How to know if the reset was successful:

Method 3: Firmware reset (for power users)

If standard methods don't work (e.g., a scooter that's getting stuck in the reset phase or has a damaged firmware), you can get back to the factory settings by flashing it back. USB-TTL (for some models) and specialized software.

The most reliable tools:

• 🖥️ DownG – the official utility from Xiaomi for firmware scooters M365/Pro.
• 🛠️ ScooterHacking Utility – supports custom firmware and deep reset.
• 🔧 XiaoFlashingTool for Models 1S/Essential.

Common algorithm:

1. Download the stock firmware for your model (for example, from the ScooterHacking website).
2. Connect the scooter to the PC through USB-C (or USB-TTL old-model).
3. Run the firmware utility and select a file with the.bin extension.
4. Start the process (usually the Flash or Write button).
5. Wait until the scooter is completed (do not turn off the scooter!).

After reflashing, the scooter will be completely reset, including:

• 📊 All user settings.
• 🔐 Account binding.
• 📉 Data on battery mileage and wear.
• 🔄 Castomic speed limits.

⚠️ Attention: Incorrect firmware can incapacitate the controller. If you are not sure of your skills, contact the service center. BLE-Module 4.0 (e.g., early modules) M365) — They are sensitive to errors when writing software.

💡

DownG firmware is the most reliable way to get the scooter back to factory status, but it requires strict adherence to instructions. Never interrupt the process or use firmware from other models!

Frequent mistakes and their solutions

Even when following instructions, users often encounter problems, and let's look at typical scenarios and how to fix them.

Problem 1: The scooter does not respond to the reset button combination.

• 🔋 Check the battery charge (should be) ≥30%).
• 🔄 Try to hold the buttons longer (up to 15 seconds).
• 🔌 Connect the charger and try again.

Problem 2: After the scooter is discharged, the scooter does not turn on.

• 🔌 Connect to the charger on 10-15 minutes, the controller may have been discharged.
• 🔧 Check the fuse (on the control board) - it could have burned when reset.
• 🖥️ Reflash through DownG (if the scooter is determined by the PC).

Problem 3: The Mi Home does not display the reset button.

• 📱 Update the application to the latest version.
• 🌐 Check your account region (in some countries, the function is hidden).
• 🔄 Use hardware reset (buttons).

Problem 4: The scooter has dropped, but it maintains speed limits.

It means that the reset has not completely passed.

• 🔧 Reset again through the buttons.
• 🖥️ Reflash the stock firmware.
• 📊 Check your settings in Mi Home – it is possible that the restrictions are set at the account level.

What to do after resetting: adjustment and calibration

Resetting to factory settings is only half the battle, and to make the scooter work properly, you need to:

1. Link to your account: Open Mi Home → Add the device → Select a model of the scooter. Follow the instructions on the screen (may need to scan). QR-scooter).
2. Calibrate the battery: Charge the scooter fully (up to 100%). Drive it until the charge drops to 0% (until the scooter shuts down). Charge again to 100% without interruption.

Set up driving parameters

• In Mi Home, set the desired maximum speed.
• Activate energy saving mode if you need a larger power reserve.
• Adjust the gas/brake sensitivity (on supported models).

It is also recommended that:

• 🔄 Update to the latest version (via Mi Home).
• 🛡️ Enable Anti-Theft if the scooter is stored in a public place.
• 📊 Reset the mileage counter (if you need to reset the statistics).

If the scooter behaves unstable after reset (for example, arbitrarily brakes or shows an incorrect charge), perform a deep calibration:

1. Turn on the scooter.
2. Press the power button. + gas + brake.
3. Wait for the beep and release the buttons.

This procedure resets controller errors and recalibrates sensors.

FAQ: Answers to Frequent Questions