How to force the phone Xiaomi: from getting stuck to “brick”

Xiaomi refused to turn on after falling, discharging or updating? The screen remains black and the charging indicator does not respond? Don't rush to carry the device to the service center. In 80% of cases, the problem can be solved yourself - just know the right sequence of actions. This article will help bring back to life even a completely dead device, regardless of the model: whether it is a Redmi Note 12, POCO X5 Pro or an outdated Mi A2.

We're going to look at all the scenarios, from basic forced restarts to EDL recovery, and the important thing is that the methods vary in complexity and risk, like Hard Reset erases all data, and incorrect use of Fastboot can turn your phone into a brick, so start with the simplest ways and move to the radical ones only if the previous ones didn't work.

Before you start, check the obvious: whether the battery is charged (plug in 30+ minutes), whether the cable or USB-C connector is damaged. If after a fall a physical defect in the case is visible, it is better to consult specialists.

1. Forced reset (Soft Reset)

The safest method that will work if the phone is stuck on the logo, does not respond to touches or is "locked" when updating.It does not delete data or require a PC connection.Suitable for all Xiaomi models, including Redmi, POCO and Black Shark.

How to do this:

1. Hold the power button for 10-15 seconds until the screen goes out.
2. If nothing happens, add a Volume Up button and hold both for 20-30 seconds.
3. After the Mi logo appears or vibration, release the buttons – the phone should boot in normal mode.

⚠️ Note: On some models (e.g, POCO F4 GT) The combination of buttons can trigger the Fastboot menu. If you see an android robot that says No command, just restart the phone again.

2. download in safe mode (Safe Mode)

If the phone turns on but shuts down immediately or is unstable (e.g., spontaneously restarts), the fault may be the damaged app. Safe mode boots the system without third-party software, allowing you to remove the problem software.

Instructions:

• 🔄 Turn off the phone (hold the power button, select Turn off).
• 📱 Hold the power button until the Mi logo appears.
• 👆 Once the logo appears, press and hold the Volume Down button until the download is complete.
• 📵 In the lower left corner of the screen should appear the inscription Safe Mode.

In this mode:

• 🗑️ Remove recently installed applications (especially from unverified sources).
• 🔍 Check the phone – if the problem disappeared, it was the fault of the software.
• 🔄 Restart your phone in normal mode.

💡

If in safe mode the phone is stable, but after a normal boot again glitch – reset to factory settings through Settings → About the phone → Reset settings.

3.Recovery through Recovery Mode

If Soft Reset didn't help, and the phone doesn't load beyond the logo, it's time to move to Recovery Mode, where you can reset, clear the cache, or install the update manually. Important: Wipe Data will delete all files, photos and apps from internal memory.

How to log in to Recovery Mode:

1. Turn off the phone (hold the power button for 20+ seconds if necessary).
2. Press the power button + Volume Up at the same time.
3. Release the buttons when the Mi logo and menu with the robot-android appear.

Further action:

⚠️ Note: On new models (Xiaomi 13, Redmi Note 12 Pro)+) Recovery menu can be in Chinese. Use translator or target icons: data reset is usually marked as (clear data).

A backup copy of the data (photos, contacts) created|Battery charge > 50%|Cable USB Type-C is serviceable|The firmware (if needed) is downloaded SD-map-->

4. Firmware via Fastboot (for power users)

If the phone doesn't respond to buttons or if Recovery Mode doesn't have a button, Fastboot mode will help, it allows you to reflash the device through your computer even if the system is completely damaged, Minimum requirements: Windows PC, USB cable, Mi Flash Tool and official firmware for your model.

Step-by-step:

1. Download the official firmware for your model (choose the Fastboot version).
2. Unpack the archive in a folder without Cyrillic characters (for example, C:\Xiaomi\proshivka).
3. Install Xiaomi and Mi Flash Tool drivers.
4. Turn off the phone and press the power button + volume reduction to enter the Fastboot (a hare in a hat-eared hat will appear).
5. Connect your phone to your PC, open the Mi Flash Tool, select the firmware folder and press Refresh → Flash.

⚠️ Attention: Continuous power is critical! If the firmware process is interrupted, the phone can turn into a brick. Use the original cable and connect the PC to the UPS).

5. Emergency firmware via EDL (for "bricks")

If the phone doesn't respond to the buttons, doesn't detect in Fastboot, and doesn't charge, there's a last chance: EDL (Emergency Download Mode) mode, which allows you to flash the device at a low level even if the bootloader is damaged.

How to activate EDL:

• 🔌 Method 1 (software): Use the command ADB: adb reboot edl (requires enabled debugging by USB and running Fastboot).
• 🔧 Method 2 (hardware): Close the contacts EDL For the Redmi Note 10 Pro, these are the contacts near the battery, for example, for the POCO X3 — near-charger.
• 🖥️ Method 3 (via Testpoint): Connect a special EDL-cable (sold on AliExpress) to the charging connector.

After activation of EDL:

1. Connect your phone to your PC – Qualcomm HS-USB QDLoader 9008 should appear in Device Manager.
2. Download firmware in.mbn format (for example, with Xiaomi Firmware Updater).
3. Use the Mi Flash Tool or QFil for firmware.

💡

EDL is the only way to bring a phone back to life with a damaged bootloader, but it requires technical skills. If you're not sure, go to the service center.

6. Checking of hardware faults

If none of the software methods worked, the problem could be the hardware, and here are the most common hardware breakdowns and their signs:

⚠️ Warning: If the phone has fallen into water or been hit hard, do not try to turn it on again, which can aggravate the damage:

• 🚫 Don't plug in to the charging.
• 🔋 Extract. SIM-card and memory card (if possible).
• 💧 Put your phone in a silica gel bag on 24.+ hour.
• 🔧 Contact the service to clean the board from corrosion.

FAQ: Frequent questions about forced inclusion of Xiaomi