Forced reboot Xiaomi Redmi Note 8 Pro: all the ways if the phone is getting stuck or not turned on

Why Redmi Note 8 Pro may require a forced reboot?

Xiaomi Redmi Note 8 Pro is a reliable device, but even it sometimes crashes: screen freeze, black screen after the upgrade, endless loading with the MIUI logo or no reaction to pressing are all signals that you need to force a restart, and unlike a conventional shutdown, this method bypasses standard system processes, which helps to regain control of the device.

The causes of the problems range from software conflicts (such as after installing custom firmware) to hardware malfunctions (a dead battery, a damaged motherboard). It is important to understand that a forced reboot does not always solve the problem forever - it only returns the phone to working condition for further diagnosis. If the failures are repeated, deep analysis or even repairs will be required.

In this article, we will look at all the current ways to reboot the Redmi Note 8 Pro, including hardware reset, working through Recovery Mode and nuances that are not written in the official instructions.

Method 1: Classic forced reboot (power buttons + volume)

It’s a versatile method that works on 90% of Xiaomi smartphones, including the Redmi Note 8 Pro. It simulates a “hard” power reset similar to the battery extraction on older phones.

How to do this:

1. Press the power button and the volume button at the same time.
2. Hold them for at least 10-15 seconds (even if the screen goes out earlier).
3. Release the buttons when the Redmi logo appears on the screen, signaling a successful reboot.

If the phone doesn't respond, try an alternative combination: power button + volume reduction. On some firmware (like custom ones), this may work better. Importantly, don't confuse this procedure with logging into Fastboot - it requires holding the buttons longer (about 20 seconds).

Make sure your phone is not connected to charging (do not short circuit risk)

Check if the Bixby button is accidentally pressed (if any)

Remember the time of holding the buttons (10-15 seconds – optimal)

If the screen blinks but the phone doesn’t restart, try again.

-->

⚠️ Warning: If after a forced reboot, the phone starts up in Safe Mode (with the label in the corner of the screen), this means that the failure is caused by a third-party app.

Method 2: Reboot via Recovery Mode (if the phone is turned on but freezes)

If the Redmi Note 8 Pro is turned on but hangs up during the MIUI boot phase, rebooting through Recovery will help.This method is milder than hard reset, but requires access to the phone's menu.

Step-by-step:

• 🔄 Turn off the phone (if it responds) or follow Method 1 for forced shutdown.
• 📱 Hold the power button. + Increase volume until the Recovery menu appears (Mi Bunny logo in the cap).
• 🌐 In the menu, select Reboot. → Reboot to System (use volume buttons for navigation, power button for confirmation).
• ⚡ If the menu is in Chinese, look for characters (reboot) or (system).

Recovery can also be reset to factory settings (Wipe Data), but this is an extreme measure - all data will be deleted!

Method 3: Reboot via Fastboot (for advanced users)

If the phone doesn't respond to buttons, but is defined by the computer as Android Fastboot, you can reboot it via the command line. ADB/Fastboot and basic knowledge of working with CMD.

Instructions:

1. Connect the Redmi Note 8 Pro to your PC via USB (use the original cable!).
2. Open the command line (Win + R → enter cmd).
3. If the phone is determined (the serial number will appear), continue. If not, install MediaTek drivers.
4. Run the reboot command: fastboot reboot

If the team doesn’t work, try an alternative:

fastboot oem reboot

It can help with the locking of the loader.

💡

Before working with Fastboot, disable the antivirus – it can block MediaTek drivers as “suspicious.”

⚠️ Attention: Fastboot erase or fastboot flash commands without understanding their actions can permanently damage the firmware!

Method 4: Reboot through battery extraction (extreme case)

The Redmi Note 8 Pro has a battery that is not removable, but in an emergency (e.g., if the phone overheats and doesn't react to anything), you can simulate its extraction, and it's a risky method, and it's only used if other methods don't work.

What to do:

• 🔧 Carefully tuck the back cover of the phone with a plastic card (start at the bottom corner where the speakers are located).
• ⚡ Do not disconnect the plumes! Just slightly lift the lid and for 10-15 seconds disconnect the contact battery (it is located in the upper part, under the metal plate).
• 📱 Collect the phone back and try turning on the power button.

This can help with hardware freezes caused by overheating or power surges, but remember: disassembling the phone on your own is insecure and can damage plumes or antennas.

💡

Battery extraction is a "swift-assist" method, and if the phone doesn't turn on after that, the problem is most likely a power controller or motherboard, and professional repair is required.

Method 5: Reboot through service codes (if the phone is partially working)

If the Redmi Note 8 Pro is powered on but is unstable (e.g., brakes or spontaneously restarts), you can use service codes for diagnosis and soft reboot.

Useful teams:

• 📞 ##4636## - Testing menu (Usage Statistics will help you find a "gluttonous" application).
• 🔄 ##7780## - resetting settings to factory (without deleting data).
• 📡 ##225## – Signal Level Check (useful if the phone is rebooting due to poor communication).

Once you have entered the code, the phone may suggest that you reboot, you can agree. If the code doesn't work, then your firmware doesn't support it (relevant to custom builds like Pixel Experience).

What if none of the methods worked?

If the Redmi Note 8 Pro doesn’t respond to all of these methods, the problem could be hardware.

• 🔋 Battery discharge: Connect your phone to charge for 30 to 60 minutes, then try to reboot again.If the indicator is not on, check the cable and power supply.
• 💧 Moisture infestation: If the phone has come into contact with water, don't turn it on! put it in rice or silica gel for 24 to 48 hours.
• 🔥 Overheating: Allow the device to cool (put on a metal surface). If it doesn't turn on after cooling, the power controller burns down.
• 🛠️ Damage to the motherboard: Diagnostics required at the service center (repair cost of Redmi Note 8 Pro – from 3000 to 8000) ₽).

If the phone vibrates but the screen is black, try connecting it to an external monitor via a USB-C to HDMI adapter, and if the image appears, there is a problem with the display plume or the matrix.

💡

Before going to the service, make a backup copy of data through the Mi PC Suite (if the phone is at least somehow determined by the computer).

FAQ: Frequent questions about the Redmi Note 8 Pro reboot