How to open Xiaomi Redmi Note 6 Pro: all ways to unlock the screen and account

Forgot the pattern lock on the Xiaomi Redmi Note 6 Pro or the phone locked after resetting?This situation is familiar to many owners of Xiaomi smartphones, especially if the device has been left unused for a long time or was bought from hand. Redmi Note 6 Pro (codename tulip) is equipped with Mi Account protection, which can turn unlocking into a real headache if you do not know the right methods.

In this article, we will look at 5 proven ways to open the Redmi Note 6 Pro, from official (via an attached account) to technical (using ADB and Fastboot). Each method is illustrated with screenshots and warnings about possible risks. Importantly, some methods require proof of ownership (checks, box), others work only when debugging is enabled via USB. Choose the appropriate option depending on your situation.

If your phone is locked after being firmware-free or reset via Recovery, you will need to bypass FRP (Factory Reset Protection), a procedure we also described below. Additional methods are available for owners of devices with an unlocked bootloader that are not suitable for locked-in devices.

1 Unlocking through Mi Account (official method)

The most reliable and secure method is to use a Xiaomi account, which works if:

• 📱 The phone is connected to the Internet (Wi-Fi or mobile network).
• 🔑 You remember the username and password from Mi Account that was tied to the device.
• 📧 The mail or phone receives a confirmation code.

Instructions:

1. On the lock screen, tap Forgot Password? (or Forgot Password?).
2. Select Sign in via Mi Account.
3. Enter your email/phone and password. If two-factor authentication is enabled, confirm the login with a code from SMS or email.
4. After successful authorization, the system will offer to create a new PIN-code.

⚠️ Note: If the phone was purchased from hand, the previous owner could not untie his account.In this case, official unlocking is possible only through Xiaomi support service with the provision of proof of purchase (check, box with a mobile phone). IMEI). Without them, the chances of success are minimal.

2. Reset settings via Recovery (data loss)

If you don't remember Mi Account data or your phone is locked after a failed firmware, you can perform a hard reset via Recovery mode, which will delete all data from your device, including photos, contacts and apps.

Step-by-step:

1. Turn off the Redmi Note 6 Pro (press the power button for 10 seconds).
2. Press Volume Up + Power at the same time and hold for 5-7 seconds until the Mi logo appears.
3. From the Recovery menu (manage volume buttons, choose the power button) select Wipe Data → Wipe All Data.
4. Confirm the action and wait for the process to be completed.
5. Restart the phone (Reboot).

⚠️ Warning: After resetting via Recovery on Redmi Note 6 Pro may work FRP-In this case, you will need to enter data from the last Mi Account associated with you or use bypass methods (see section 4).

3. Unlock via ADB (if debugging is enabled)

The method is suitable if the phone was previously enabled debugging USB (USB Debugging. This is rare, but if you activate this feature, the chances of successfully unlocking it are high.

What you need:

• 🖥️ Computer with Windows/Linux/macOS.
• 🔌 USB-cable (original or quality).
• 📦 Installed Xiaomi drivers and tool ADB.

Instructions:

1. Connect your phone to your PC via USB.
2. Open the command line (Win + R → enter cmd).
3. Enter the commands in order: adb devices (the tulip device should appear - this is the code name Redmi Note 6 Pro). adb shell su rm /data/system/gesture.key rm /data/system/password.key reboot
4. After the restart, the phone will unlock, but you will need to reconfigure the pattern lock.

⚠️ Attention: If debugging is on USB It wasn't activated beforehand, it won't work. ADB without prior configuration leads to an unauthorized error.

4.FRP bypass on Redmi Note 6 Pro after reset

If you reset your phone after resetting it through Recovery, you need to bypass FRP (Factory Reset Protection), which runs on MIUI 10-12 firmware and requires access to Fastboot.

Tools required:

• 🖥️ PC with Mi Flash Tool and drivers installed.
• 🔌 Original. USB-cable.
• 📁 Firmware for Redmi Note 6 Pro (Fastboot version).

Step-by-step:

1. Turn off the phone and turn to Fastboot mode (clip Volume Down + Power).
2. Connect to your PC and check for device detection by command: fastboot devices
3. Download the official firmware for tulip (choose the Fastboot version).
4. Unpack the archive and launch the Mi Flash Tool.
5. In the program, select the firmware folder, specify Clean all mode and press Flash.
6. After flashing the phone will restart without FRP-locking.

⚠️ Attention: This method deletes all data and resets the phone to factory settings, and there is a risk of bricking if you interrupt the firmware process!

💡

Before you run through the Fastboot, check the battery level — it should be at least 60%. If the phone runs out during the process, it will be extremely difficult to restore it.

5. Alternative methods (for experienced users)

If standard methods don't work, you can try more complex ones, they require technical skills and they don't guarantee 100% results.

Ways for Advanced Users:

• 🔧 Flip-through EDL (Requires an authorized Xiaomi account and a special cable.
• 🛠️ Replacement of the motherboard (if the lock is related to a hardware malfunction).
• 📱 Use of exploits (e.g. vulnerabilities in the MIUI 9-10 to bypass the lock).

For the EDL method, you will need:

1. EDL cable (or homemade adapter with contact closure).
2. Mi Flash Pro or QFil.
3. The firmware is.mbn for the Redmi Note 6 Pro.

⚠️ Attention: Firmware through EDL Without authorization, Xiaomi may lead to a lock IMEI (The phone will lose communication with the networks of operators!

Frequent Mistakes and How to Avoid Them

When unlocking the Redmi Note 6 Pro, users often face typical problems, and here are the most common ones and ways to solve them:

Error 1: Phone is not defined in Fastboot or ADB.

• 🔌 Check it out. USB-cable (use the original cable).
• 🖥️ Reinstall Xiaomi drivers (download from the official website).
• 🔄 Try another one. USB-port (preferably) USB 2.0).

Error 2: After the reset, the message appears: "This device is locked."

This means that the bootloader is locked.

• 📱 Send an unlock request via Xiaomi’s official service (you will need a tied account and wait 720 hours).
• 🛠️ Use informal methods (such as Deep Flash Cable) but it is risky.

Error 3: The firmware running the Mi Flash Tool ends with a “Flash Not Done” error.

Causes and solutions:

• 📁 Wrong firmware version (download only for tulip model).
• 🔋 Low battery charge (charge at least 60%).
• 🔌 Problems with USB-Connection (try another port or cable).

💡

If the phone was bought by hand, always check before buying whether the Mi Account is untied. ask the seller to reset the settings on you and make sure the device does not require you to enter an old account.

FAQ: Answers to Frequent Questions