How to Disable Fastboot on Xiaomi: 5 Verified Ways (2026)

Fastboot mode on Xiaomi, Redmi and POCO smartphones is a special engineering mode that is used to firmware, unlock the bootloader or restore the system. However, many users face a situation where the phone gets stuck in this mode after a failed update, resetting or experimenting with custom firmware. If your Xiaomi constantly loads into Fastboot Mode with a picture of a rabbit in a hat-eared, do not worry – there is a way out.

In this article, we will discuss all the working ways to disable Fastboot, including software and hardware methods, and explain why a smartphone can freeze in this mode. The instructions are relevant for models from 2018-2026 (from Redmi Note 7 to Xiaomi 14 Ultra) and take into account the latest changes in MIUI policy. If you are not sure about your actions, read the section on risks and prepare in advance.

Why Xiaomi is loading into Fastboot and how to fix it

Fastboot mode starts automatically in several cases:

🔄 Failed software update - interrupted firmware through MIUI Updater or Recovery.
🔓 Unlocking the bootloader – if the process was interrupted or performed with errors.
📱 Reset to factory settings via Hard Reset with button retention.
🔋 Battery problems – if the battery is under 5% during critical operations.
🛠️ Hardware failures - damage to the connector USB-C power-button.

80 percent of the time, the problem is solved software-based, but if the smartphone doesn't respond to commands or PC connectivity, it will require a diagnosis at a service center. On models with a Snapdragon processor (such as the POCO F5 or Redmi K60), the chance of recovery is higher than on devices with MediaTek chips (Redmi Note 12 series), where the Fastboot is often blocked at the firmware level.

Before you start taking action, check:

Battery charge > 30% (connect charging)

USB C-C or C-A cable (original)

Windows 10/11 computer and administrator rights

Installed drivers Mi Flash Tool or ADB

Backup data (if the phone has previously worked)

-->

Method 1: Standard button exit (for most models)

If your smartphone responds to physical buttons, try a forced reboot, which works on 90% of Xiaomi devices, except for models with a damaged power button.

Hold the Power button for 10-15 seconds until the screen goes out.
If the phone vibrates but boots back into the Fastboot, repeat the action by holding Power + Volume Up.
Some models (such as the Xiaomi 13T) require you to hold Power + Volume down until the MI logo appears.

If you read No Command or the MIUI logo with an exclamation point after the reboot, it means that the phone is trying to download Recovery.

🔄 Press Power. + Increase volume by 3 seconds to enter Recovery Mode.
📱 Select the Reboot option → System (use volume buttons for navigation).

💡

If the buttons don't respond, check for mechanical damage. Often the reason for hanging in the Fastboot is sticking the Volume Down button (especially after falls or moisture).

Method 2: Exit via Mi Flash Tool (for hardwired devices)

If the standard reboot didn’t work, you’ll need to connect to a PC and use the official Mi Flash Tool.This method is suitable for devices with an unlocked bootloader or if you’ve previously flashed your phone through Fastboot.

Step-by-step:

Download and install the Mi Flash Tool (version no lower than 2023.4.1).
Connect your phone to your PC via USB (use the rear USB 3.0 port on the system unit).
Run MiFlash.exe on behalf of the administrator.
Press Refresh – your Xiaomi should appear on the device list (e.g., tissot for the Redmi Note 7).
Select Flash action and specify the path to the official firmware (file with the extension.tgz).
Click Clean All (complete clean) or Save User Data (save data).
Wait for the process to be completed (10-20 minutes) and the phone will automatically restart.

Important: If the Mi Flash Tool doesn’t see the device, check:

🔌 Port connection USB 2.0 (on some PCs) USB 3.0 is incompatible with Fastboot).
🖥️ Have Qualcomm drivers been installed? HS-USB QDLoader 9008 (for Snapdragon) or MediaTek Preloader.
🔄 Try another cable - the original one USB-C from Xiaomi or certified USB-IF.

What to do if the Mi Flash Tool gives you a "Couldn't load device" error

The error occurs due to driver conflict or antivirus lock. Solution: 1. Disable Windows Defender protection and antivirus (such as Kaspersky or Avast). 2. Remove all Xiaomi drivers through Device Manager (section "USB Controllers"). 3. Reinstall the drivers manually via MiFlash (the Driver button in the menu). 4. Try to start MiFlash in Windows 7 compatibility mode.

Method 3: ADB and Fastboot commands (for power users)

If the Mi Flash Tool didn't help or you have custom firmware, try logging out of Fastboot via the command line.This method requires ADB and Fastboot drivers installed.

Instructions:

Download Google’s Platform Tools and unpack the archive.
Connect your phone to your PC and open the Command Prompt in the platform-tools folder (click Shift + PCM → Open the PowerShell window here).
Enter the command to check the connection: fastboot devices If the device is displayed (for example, 1234567890abcdef fastboot), go further.
Run the reboot command: fastboot reboot If the phone is back in Fastboot again, try resetting the cache: fastboot erase cache fastboot reboot

Devices with a locked bootloader (Redmi Note 11, POCO X5 and later) may need to be unlocked via the Mi Unlock Tool. Official instructions from Xiaomi require you to link your Mi Account and wait 7-15 days to unlock.

Rebooting with buttons

Mi Flash Tool

ADB/Fastboot teams

Another way (write in the comments)

I've been out of here.-->

Method 4: Recovery through EDL Mode (Emergency Mode)

EDL Mode (Emergency Download Mode) is a hidden mode for Xiaomi recovery when Fastboot is unavailable. It is activated when critical firmware failures or boot partition damage. On 2023-2026 models (such as Xiaomi 13 or Redmi Note 12 Pro+), EDL is only available through authorized service tools or test points on the board.

How to log into EDL:

Turn off the phone (hold power + Volume up before switching off).
Press Power + Volume Down and connect the USB cable to the PC.
Device Manager should have a Qualcomm HS-USB QDLoader 9008 (for Snapdragon) or MediaTek Preloader.

For firmware in EDL, use:

📱 Mi Flash Tool (Snapdragon only).
🖥️ SP Flash Tool (for MediaTek).
🔧 Authorized boxes (e.g. UFi Box or EasyJTAG for new models).

⚠️ Attention: Firmware through EDL Without official permission, Xiaomi may be blocked. IMEI on models with anti-Rollback protection (for example, POCO F4 or Redmi K50). Before you act, check the firmware version via the command: fastboot getvar anti If the value is anti: 4 and above – do not stitch the old versions. MIUI!

Method 5: Hardware reset (if nothing helps)

If the software methods didn't work, it could be a hardware failure, most of the time it's:

🔋 Failed battery – if the phone turns off at 20–30% charge.
🔌 Damaged connector USB-C — oxidation.
🛠️ The dump of a memory chip (e.g., eMMC or UFS).
📱 Problems with the power button - closure or mechanical wear.

What you can do on your own:

Try charging your phone with another cable and power supply (at least 18 watts).
Check the USB-C connector for damage or debris (use a flashlight).
If the phone warms up when connected to a PC, this is a sign of a short circuit on the board.

To diagnose hardware problems will require:

Symptoms.	Possible cause	Decision
The phone vibrates, but does not turn on	Damaged plume display or battery	Replacement of battery or plume
Fastboot only appears when connected to a PC	Short circuit in the USB-C connector	Replacement of connector or soldering of contacts
The phone turns off at 15-20% charge	Battery wear or power controller failure	Battery replacement + calibration
Fastboot with Invalid Partition	Damage to the boot or system partition	Firmware via EDL with full formatting

⚠️ Note: If after battery replacement or connector USB-C The phone still does not leave the Fastboot, the reason may be damage to the power chip (for example, PMIC). In this case, repairs are only possible in a service center with micro soldering equipment (e.g. Quick station). 861DW).

Frequent Mistakes and How to Avoid Them

Many users make the problem worse by trying to "solve it fast."-5 Mistakes when leaving Fastboot:

🔄 Use of informal firmware - custom ROM (LineageOS can block Fastboot on new models.
📱 Interrupting the firmware – if the Mi Flash Tool process is interrupted by 50-70%, the phone can turn into a brick».
🔋 Low battery firmware – if the charge is less than 10%, the device will turn off in the process.
🖥️ Use of outdated drivers - Fastboot drivers from 2019 year-over-year MIUI 14/15.
🔧 Independent disassembly of the phone - without experience you can damage plumes or chips.

How to minimize the risks:

🔄 Always check the firmware version on the official Xiaomi website.
📱 Use only original cables and power supplies.
🔋 Before firmware charge your phone to 100% and connect to a UPS (if there is a risk of power outages).
🖥️ Turn off Windows antivirus and firewall before working with the Mi Flash Tool.

💡

If the phone is stuck in Fastboot after an air-to-air update (OTA), never stitch it through the Mi Flash Tool without a backup! first try resetting the cache through ADB commands or wait for the system to recover automatically (can take up to 30 minutes).

FAQ: Answers to Frequent Questions

My Xiaomi got stuck in Fastboot after resetting.

If the reset was done via Settings → Reset, try: Hold Power + Volume Up 10 seconds for forced reboot. If it doesn't work, connect to your PC and execute the command fastboot reboot. If the phone returns to Fastboot, run the official firmware through the Mi Flash Tool (select Clean All).

Fastboot only appears when you connect to a charger. Is that a hardware problem?

The symptom indicates: Short circuit in the USB-C connector (replacement needed); damage to the power controller (e.g., the BQ25890 chip on the Redmi Note 10); battery contacts collapse (check if it's swelling); self-repair is only possible when the connector is replaced; contact the service for diagnostics of the power controller.

Can I log out of Fastboot without a computer?

Yes, but only if: The phone responds to buttons (try to hold Power + Volume Up 15-20 seconds). The battery is at least 10% charged (plug in charge for 30 minutes). The problem is not with firmware damage (e.g., the phone loads into Fastboot after a failed update). If the phone doesn't respond to buttons or constantly returns to Fastboot, you can't do without a PC.

After logging out of Fastboot, the phone asks for a password from the Mi Account.

This is FRP (Factory Reset Protection) to unlock: Enter your Mi Account (if you remember the password). If you don't remember, use password recovery. If your account is not yours (the phone is bought by hand), contact the previous owner or the service to untie the EDL (you need a check or box). On models with MIUI 13+, you can't bypass FRP without the original account!

Can I flash Xiaomi into Fastboot without unlocking the bootloader?

No, on most Xiaomi models (except the older ones like the Redmi 4X), Fastboot firmware requires an unlocked bootloader. Exceptions: Official updates via MIUI Updater (do not require unlocking); Firmware via Recovery (if not damaged); Recovery via EDL with an authorized service center account. To unlock the bootloader, you need to link the Mi Account and wait 7-15 days (Xiaomi 2023 rules).