How to turn off Fastboot on Xiaomi phone: all working ways

Why Xiaomi Phone Hung in Fastboot Mode and How to Fix It

Fastboot mode on Xiaomi smartphones (including Redmi, POCO and Black Shark) is a special diagnostic mode that is used to firmware, unlock the bootloader or restore the system. However, sometimes the device can get stuck in this state: the screen displays a hare in a hat-out (Fastboot logo), and the phone does not respond to conventional shutdown methods. The reasons for this behavior are diverse, from accidental button pressing to failure when updating the software.

If your Xiaomi is not leaving Fastboot, don't panic. 90% of the time, you can fix the problem without going to the service center, and the main thing is to correctly identify the cause and find the exit method. In this article, we will discuss all the current ways to disable the mode, including forced reboot, reset via Mi Flash Tool, and even manual commands for experienced users. 13T), where standard methods may not work.

Before you start taking action, check:

• 🔋 The battery level (should be at least 30%, otherwise the risk of “filling” the device increases).
• 🔌 Is the phone connected to charging (preferably the original cable).
• 🖥️ Is there access to a computer with Mi drivers installed? PC suite ADB/Fastboot Tools.

Unsuccessful update | PC Connections | Accidental button press | Other action |I don't know-->

Method 1: Forced Reset (Hard Reset)

The easiest and safest method is hardware reset, which works on most Xiaomi models if the Fastboot mode is caused by a software failure, not a hardware breakdown.

1. Press the power button for 10-15 seconds (on some models - up to 20 seconds).
2. If the screen is gone, but the phone is back on Fastboot, repeat the action 2-3 times.
3. On models with a non-removable battery (for example, Xiaomi 12 Pro or Redmi K50) hold Power + Volume up to vibration.

If the phone doesn’t respond to button retention, try the combination:

Power + Volume reduction (hold 10-15 seconds)

Turn off the charger.

Make sure the buttons are not stuck

Try to press buttons with different strengths.

Wait 1-2 minutes between attempts-->

Important! On some devices (like the POCO F5 or Black Shark 5), button combinations may differ. If the standard method didn't work, refer to your model documentation.

⚠️ Warning: Do not use metal objects (clips, needles) to press buttons - this can damage the contacts or display.If the buttons are not physically pressed, the problem may be mechanical damage.

Method 2: Exit through the Mi Flash Tool (for PC)

If the forced reboot doesn't work, you'll need to connect to a computer.

• 🖥️ Windows computer 7/10/11 (MacOS or Linux may have driver problems).
• 🔌 Original. USB-cable (preferably from the set).
• 📥 Installed program Mi Flash Tool (you can download from the official website of Xiaomi).
• 🔑 Unlocked bootloader (if the phone hasn’t unlocked before, this method may not work).

Instructions:

1. Connect your phone in Fastboot mode to your PC.
2. Run the Mi Flash Tool and wait for the program to identify the device (the name of the model should appear in the list).
3. Press the Refresh button, then select the Clean All option (this will delete all data but save the bootloader unlock).
4. Click Flash and wait until the process is complete (usually 5-10 minutes).

If the Mi Flash Tool gives you a "Couldn't flash" error, try reinstalling drivers manually through Device Manager (select "MI Flash Interface" in the "Other Devices" section).

💡

If the Mi Flash Tool doesn’t see the phone, try running it on behalf of the administrator or temporarily disabling the antivirus (it can block access to drivers).

Method 3: ADB and Fastboot commands (for advanced users)

If you have experience with ADB and Fastboot, you can try to exit mode via the command line, a method that is suitable for models with an unlocked bootloader (for example, Xiaomi Mi 11 or Redmi K40).

Steps:

1. Install ADB and Fastboot Tools (you can download from the XDA Developers website).
2. Connect the phone to your PC and open the command line (Win + R → enter cmd).
3. Check the connection command: fastboot devices If the device is determined (serial number will appear), enter: fastboot reboot

If the fastboot reboot command doesn’t work, try:

fastboot oem reboot-recovery

This will reboot the phone to Recovery mode, from where you can reset to factory settings.

⚠️ Note: On some models (e.g, POCO X5 Pro) The fastboot oem unlock command can result in complete data cleanup. Do not use it unnecessarily!

Method 4: Battery Removal (for older models)

On Xiaomi smartphones before 2018 (e.g. Redmi 4X, Mi 5), the battery was removable, in which case you can physically turn off the power:

1. Remove the back cover (a plastic shoulder blade or mediator will be required).
2. Carefully disconnect the battery plume for 10-15 seconds.
3. Connect the battery back and try to turn on the phone.

Warning: On newer models (starting with the Redmi Note 7), the battery is non-removable, and trying to remove it without experience can damage the plumes or bloat the battery!

If you are not sure of your skills, you should use other methods or contact the service. The opening of the case also deprives you of warranty (if it is still valid).

💡

Physical battery shutdown is a last resort, and only use it if your phone is not responsive to software and you have experience disassembling the equipment.

Frequent reasons for hanging out in Fastboot and how to avoid them

Fastboot mode is usually activated in the following cases:

• 🔄 Interrupted software update (for example, if during the installation of firmware, the battery or phone has turned off from the PC).
• 🔌 Incorrect connection to the computer (use of unoriginal cable or USB-hub).
• 🛠️ Attempting to unlock the bootloader without following instructions (for example, missing the Mi Account link step).
• 🎯 Accidental pressing of the button combination (for example, Powering) + Reduce the volume when removing the phone from your pocket).

To minimize the risk of re-hang:

• 🔋 Always monitor your battery level before upgrading (50 percent or higher optimal).
• 🔌 Use the original Xiaomi cables and chargers.
• 🖥️ When you run through a PC, turn off all unnecessary USB-Devices (muses, flash drives) – they can conflict with phone drivers.
• 📱 Do not accidentally press buttons when connecting to a PC (especially if the phone is in your pocket or bag).

If the phone regularly spontaneously goes to Fastboot, it may indicate:

• Problems with the button Power or Loudness (sticking, oxidation of contacts).
• Damage to the USB connector (for example, after falling or getting moisture).
• Failure of the loader (reflashing is required).

What do you do if nothing helps?

If none of the above methods worked, there are two options:

1. EDL-Emergency Download Mode is an emergency firmware mode that is available even when the bootloader is damaged:

⚠️ This method is risky, because if you make a mistake, the phone can turn into a brick!

1. Contacting a service center -- if you have a warranty phone or you're not sure what you're doing, it's the most reliable option.

The cost of repairs in informal services is usually 1,500-3,000 rubles (depending on the model and complexity of the work).In official Xiaomi centers, the price may be higher, but you will get a guarantee for the work performed.

💡

If the phone is stuck in the Fastboot after a failed firmware, do not try to stitch it again without diagnosis - this can aggravate the problem.

FAQ: Answers to Frequent Questions