IP-Xiaomi router address: where to see how to change and what to do if it does not open

Introduction: Why is it necessary IP-Xiaomi router address and where to look for it

IP-The Xiaomi router address is a digital device passport on your local network that allows you to access your device's settings through your browser. Without it, you can't configure Wi-Fi, change your password, update your firmware or configure your guest network. 4A, AX3000, 4C, Pro) use the standard 192.168.31.1 address by default, but it may vary depending on the firmware version or provider settings.

The problem is that users often face a situation when the router is “not visible” on the network: the settings page does not open, but the standard one is not visible. IP It's not working. It could be because of address conflict, a malfunction. DHCP or changes in network configuration. In this article, we'll look at all the ways to find the current one. IP-Address your Xiaomi router, change it if necessary and fix common access errors.

Important: if you are using a router in repeater mode or connected to it via a bridge (WDS), his IP In such cases, additional steps will be required to determine the current address.

Standard. IP-Xiaomi router addresses by model

Most Xiaomi routers use one of three standard addresses on the local network, but some models (especially new or designed for foreign markets) may have different values.

⚠️ Note: If you have previously changed your network settings or a router was purchased by hand, the standard IP In this case, use the methods in the next section to find the current address.

Also note that some providers (such as Rostelecom or Beeline) may block access to router settings through standard IP. In such cases, you will need to reset to factory settings or use the Mi Home app.

How to find out the current IP-Xiaomi router address: 5 working methods

If the standard address is not working or you are not sure which one is IP It's used, use one of the proven methods below. We've put them from the simplest to the most complex.

1. Through a sticker on the router's body

On the bottom or back of most Xiaomi routers, there is a sticker with technical information.

• 🔹 IP-address (e.g. 192.168.31.1)
• 🔹 Name of the Wi-Fi network (SSID) password
• 🔹 MAC-Address (useful for linking to provider)
• 🔹 Firmware version (relevant to older models)

If the label is erased or there is not enough information, proceed to the next method.

2. Through the command line (Windows/macOS/Linux)

This is a universal method that works on any device connected to the router via cable or Wi-Fi.

For Windows:

1. Open the Command Prompt (Win + R → enter cmd → Enter).
2. Enter the command: ipconfig
3. Find the main gateway line – this is the IP of your router.

For macOS/Linux:

1. Open the Terminal.
2. Enter the command: netstat -rn | grep default
3. IP-The address after the word default is the router's address.

💡 Useful tip: If you’re connected to the router via Wi-Fi but the command doesn’t show the gateway, try connecting via cable – sometimes it helps to avoid errors DHCP.

3.Through the Mi Home app

The official Mi Home app (available for Android and iOS) automatically detects the IP-The address of the connected router:

1. Open Mi Home and go to the Devices section.
2. Select your router from the list.
3. Press three points (⋮) top-right → Settings.
4. The Network Status or Local Network section will indicate the current IP.

⚠️ Note: If the router doesn’t show up in Mi Home, check if you’re connected to its Wi-Fi network.The app won’t see the device if you’re using mobile internet or another access point.

4. Through the web interface of the provider

Some Internet Service Providers (for example, MGTS or Dom.ru) provide access to the settings of the router through the personal account:

1. Go to your provider’s website and log in.
2. Find the section My devices or equipment.
3. The router information will indicate its local IP.

This method only works if the router was issued by the provider or linked to its network.

5. Through third-party apps (for Android)

If the previous methods did not work, use the utilities to analyze the network:

• 📱 Fing (scans the network and shows all connected devices from their network) IP)
• 📱 Network Analyzer (defines the default gateway)
• 📱 WiFi Analyzer (shows access point information)

After scanning the network, find a device with a name Xiaomi_XXXX or MiWiFi_XXXX — his IP and will be the router's address.

Try the standard address (192.168.31.1)

Check the sticker on the body

Use the command ipconfig/netstat

Launch the Mi Home app

Scan the network through Fing-->

How to change IP-Xiaomi router address: step-by-step instructions

Change of change IP-Addresses may be required in several cases:

• 🔄 Conflict with another device on the network (for example, if you have two routers with the same network) IP).
• 🔒 Blocking access by the provider to the standard address.
• 🛠️ Set up a complex network with multiple subnets.

For a shift. IP Follow the following steps:

1. Enter the web interface

1. Connect to the router via cable or Wi-Fi.
2. Open the browser and enter the current one. IP (for example, 192.168.31.1).
3. Sign in using the password from the sticker or previously installed.

2. Transition to network settings

Depending on the model and firmware, the path may differ:

• For the Mi Router 4A/4C: Additional settings → Network → LAN
• For AX3000/AX6000: Settings → Local area network → Parameters LAN
• For older firmware: Advanced Settings → Network → LAN

3.Amendment IP-address

In the section LAN You'll see the fields:

• IP-Address – enter a new address (e.g. 192.168.10.1).
• The subnet mask is usually 255.255.255.0.
• DHCP-server – turn it on if you need to give IP automatically.

⚠️ Attention: After the change IP The router will reboot, and you'll have to connect to it at a new address, and if you make a mistake, you may lose access to the Internet!

4. Save and restart

Click Save or Apply. The router will reboot (this can take 1-2 minutes).

1. Unplug the network and reconnect.
2. Enter a new one. IP in the browser to ensure the performance.

🔧 A useful tip: If after the shift IP router is no longer available, reset to factory settings (press the Reset button for 10 seconds.

Common mistakes when working with IP-Xiaomi address and their solutions

Even after you set it up properly, users often face access issues, and let's look at the most common errors and how to fix them.

1. The settings page does not open (ERR_CONNECTION_REFUSED)

Causes and solutions:

• 🔌 The router is not powered on or connected to the power supply – check the indicators on the case.
• 🌐 Wrong. IP-Address – Use the methods in the section above to find the current address.
• 🔒 Antivirus/firewall lock – temporarily turn off protection and try again.
• 📡 Connection through VPN — turn off VPN-Programs (they can redirect traffic).

2. Requests login and password, but they do not fit

In Xiaomi routers by default:

• 🔑 Login - not required (leave the field empty).
• 🔑 Password – listed on a sticker under the router (usually 8 characters, such as 12345678).

If the password doesn't fit:

1. Try admin or 1234567890 (standard passwords for old firmware).
2. Reset the settings with the Reset button (hold 10-15 seconds).
3. If the router is purchased by a used one, contact the previous owner – he may have changed the password.

3. IP-The router’s address conflicts with another device

Symptoms of conflict:

• ⚠️ The Internet is intermittent.
• ⚠️ The settings page is now open, then not.
• ⚠️ In the network appear devices with duplicate IP.

Decision:

1. Change. IP router to another router (for example, from 192.168.31.1 to 192.168.32.1).
2. Disable another device with conflicting IP (Find him through arp. -a command-line).
3. Set up static. IP for critical devices in the section DHCP → Reservation of addresses.

4. After the shift. IP Internet gone missing

This happens if:

• 🔌 Incorrectly specified subnet mask (must be 255.255.255.0).
• 🔌 New IP off-range DHCP (For example, the router is giving away 192.168.31.100-200 and you set 192.168.31.250).
• 🔌 Conflict with provider settings (some operators link services to a specific service) IP).

Decision:

1. Bring back the old one. IP and check the settings. DHCP.
2. Contact your provider if the internet is not restored.

💡

If, after the change, IP The router is no longer available, use the reset button Reset. Hold it for 10-15 seconds until the flashing of the indicators - this will return the factory settings, including the standard address 192.168.31.1.

Features of working with IP in different Xiaomi firmware

Xiaomi routers run on three types of firmware that affect access to settings and management IP-address:

1. Standard firmware (MiWiFi)

This is a factory firmware installed on most models (4A, 4C, AX3000). Features:

• 🔹 Accessed by 192.168.31.1 or miwifi.com.
• 🔹 Support for Mi Home app support.
• 🔹 Ability to update via web interface.

This firmware change IP It is done through the Additional settings section. → Network → LAN.

2. Firmware for the EU (EU ROM)

Adapted for the European market, different:

• 🔹 Standard. IP can be 192.168.0.1 or 192.168.1.1.
• 🔹 No link to Mi Account.
• 🔹 Support for English in the interface.

⚠️ Attention: B EU ROM There is no miwifi.com function – use only digital IP.

3. Custom firmware (Padavan, OpenWRT)

Users often install alternative firmware for advanced features, including:

• 🔹 IP-The address can be any (depending on the user settings).
• 🔹 The web interface is different from the standard.
• 🔹 For modification IP You need to go to the Network section. → LAN.

💡 Useful tip: If you use Padavan, check the configuration file /etc/config/network through SSH — it's written down IP.

How to set up static IP for devices on the Xiaomi network

If you want to use certain devices (for example, IP-camera NAS) They always got the same thing. IP-address, use the reservation function DHCP. It's useful:

• 📹 Connecting CCTV cameras.
• 🖥️ Remote access to the PC.
• 🎮 Port settings for gaming consoles.

Instructions for Xiaomi routers:

1. Go to the router's web interface.
2. Go to the section: Additional settings → Network → DHCP.
3. Find the Address Reservation or Static block DHCP.
4. Click Add and select the device from the list of connected.
5. Specify what you want. IP-address (e.g. 192.168.31.100).
6. Save the settings and restart the router.

⚠️ Attention: Static IP should be out of range DHCP. For example, if a router gives out addresses from 192.168.31.100 to 192.168.31.200, reserve IP in the range 192.168.31.2–99 or 192.168.31.201–254.

🔧 Useful tip: To avoid conflicts, check before booking whether the selected one is used IP For this purpose, enter in the browser:

ping 192.168.31.100

If there is no answer, the address is free.

Frequently Asked Questions (FAQ)