IP-Xiaomi router address: where to see and how to change in 2026

Introduction: Why is it necessary IP-router address?

IP-The router’s address is its “digital passport” on the local network, which allows you to access the control panel, change Wi-Fi settings, update firmware or configure functions like guest network and parental control. Without this address, you will not be able to access the device’s web interface, even if you are connected to its network.

Xiaomi routers (including Mi Router models) 4A, AX3600, AX6000 Redmi Router AC2100) IP-The default address is usually standard, but can vary depending on the provider's settings or manual edits. In this article, we will discuss all the ways to determine it, from universal methods for any device to specific instructions for different operating systems.

Important: If you have previously changed your network settings (e.g., enabled AP Mode or configured dual NAT), standard IP may not work, and in such cases, alternative methods will be required, which we will also describe below.

Standard. IP-Xiaomi router addresses by model

Most of the Xiaomi routers use one of three IP-You can try to type them into the browser address bar to get into the control panel:

• 🔹 192.168.31.1 — The most common address for most models (Mi Router) 3/4/4A/4C, Redmi Router AC2100).
• 🔹 192.168.0.1 - Used in some firmware for AX3600 and AX6000, and also in the repeater mode (Repeater Mode).
• 🔹 192.168.1.1 – rare, but may occur in older versions of the software or after resetting to factory settings.

If none of the addresses opens the control panel, then the IP has been manually changed or assigned by the provider, in which case, move on to the next sections with alternative methods of determining.

⚠️ Note: If the router is connected to the provider’s network via PPPoE or DHCP, local IP It may be different from the factory, and in this case, use the methods in the following sections.

How to find out the IP router Xiaomi on Windows 10/11

If standard addresses don't work, you can determine the current IP of the router through the command line or network parameters.

Method 1: Through the Command Line (CMD)

This is a universal method that works on all versions of Windows:

1. Press Win + R, enter cmd and press Enter.
2. Enter the command: ipconfig /all
3. Find an Ethernet Adapter or Wireless Network Adapter (depending on the type of connection).
4. IP-The router address will be specified in the main gateway line (e.g. 192.168.31.1).

Method 2: Through Network Parameters

A more visual method for users not familiar with the command line:

1. Open the settings. → Network and Internet.
2. Choose Ethernet (for cable connection) or Wi-Fi.
3. Click on your network name, then click Properties.
4. Scroll down to the block. DNS-server — IP The router will be listed as the default gateway.

💡

If the ipconfig results show an IP of 169.254.x.x, it means your computer is not receiving an address from the router.

Definition of IP on macOS, Linux and mobile devices

Users of MacBook, iPhone or Android smartphones can also easily recognize the IP of Xiaomi router without access to the web interface.

On macOS (Monterey, Ventura, Sonoma)

Open the Terminal (can be found via Spotlight on Terminal request) and type:

netstat -nr | grep default

IP-The router's address will be listed in the Gateway column. Alternatively, you can go to System Settings. → Network → Additionally. → TCP/IP And look at the router line.

On Android (MIUI, Stock Android, Samsung One UI)

In most firmware, the path is as follows:

1. Open the Settings. → Wi-Fi.
2. Tap your network name (there will be a tick Connected).
3. Scroll down to the Additional block or Network Settings.
4. The IP router will be listed as a Gateway or Gateway.

On smartphones Xiaomi with MIUI The path may be slightly different: → Wi-Fi → ⚙️ (gear-plate) → Advanced settings → IP-address.

On iPhone or iPad (iOS 15/16/17)

Apple hides this information more deeply, but it can be found:

1. Open the Settings. → Wi-Fi.
2. Slip on the i symbol next to your network name.
3. Scroll down to the TCP/IP block – the router’s IP will be in the Router bar.

How to go to the settings of the Xiaomi router after determining the IP

When did you find out? IP-The address, you just have to log in to the web interface:

1. Open any browser (Chrome, Edge, Safari) and enter the IP in the address bar (e.g. http://192.168.31.1).
2. Enter your username and password. For most Xiaomi models: 🔑 Login: admin 🔑 Password: Indicated on the sticker at the bottom of the router (if not changed).

Reset

Note: if after entering the IP browser redirects you to the provider’s page (for example, “Rostelcom Home Network”), then the router operates in Bridge Mode, in which case access to its settings may be limited.

Make sure you are connected to the router network|Check that IP introduced https://|Use the browser in incognito mode (without extensions)|Turn it off. VPN, if he's active-->

What to do if the IP of the router has changed or does not open

Sometimes. IP-The router’s address may be “lost” because of:

• 🔄 Failure to work DHCP-router.
• 📡 Conflict with another device on the network (e.g., a second router).
• 🔧 Manual changes in settings (bridge mode, static) IP).

Decisions:

1. Restart the router (turn off power for 30 seconds).
2. Reset the settings with the Reset button (hold 10-15 seconds).
3. Check the connection: If you are using a cable, try a different LAN port.
4. Turn off additional routers on the network (if any).

⚠️ Note: If the router does not issue after resetting IP (in ipconfig is displayed 169.254.x.x), It's probably damaged. In this case, you'll need to flash it through the mode. TFTP (For instructions for your model, look for the forum 4PDA).

💡

If the Xiaomi router does not open the web interface even after reset, check if the AP Mode is enabled. In this mode, the IP may differ from the standard one, and some functions will not be available.

How to change IP-Xiaomi router address manually

By default, you do not need to change the router’s IP, but it may be necessary to:

• 🔧 Avoiding conflicts with another router on the network.
• 🔒 Improved security (hiding a standard address).
• 📡 Set up complex networks (for example, with multiple subnets).

Instructions for modification:

1. Go to the router control panel (e.g. 192.168.31.1).
2. Go to Additional settings → Network → LAN.
3. In the field IP-Enter a new address (e.g. 192.168.10.1).
4. Save your settings and reconnect to the network.

Important: once the IP changes, all the devices on the network will lose their connection, and they will have to be reconnected manually or rebooted.

Frequent mistakes and their solutions

When working with IP-Xiaomi routers often face typical problems. Let's analyze the most common:

• 🚫 Page won't open: Check that you're connected to the router network (not the mobile Internet). VPN Try another browser (like Firefox instead of Chrome).
• 🔄 IP It is normal to have a dynamic one. IP It's not typical for a local router address. IP (For example, from 192.168.31.1 to 192.168.0.1), check the settings. DHCP.
• 🔒 Password doesn't fit: If you haven't changed your password, look it up on the sticker at the bottom of the router. 3) try admin/admin. If nothing helps, reset with the Reset button.

💡

If Xiaomi router issues IP but doesn’t let it into the control panel, you may have “Disable WAN” enabled, disable it in security settings, or reset the router.

FAQ: Answers to Frequent Questions