How to go to the settings of the router Xiaomi AX1800: 5 ways + error solving

Owners of the Xiaomi Router router AX1800 Sooner or later, they're faced with the need to change the network settings, change the Wi-Fi password, set up guest access or update the firmware, but the first step, logging into the control panel, often raises questions. IP-What username and password to use? Why doesn't the page open?

This article will help you understand all the nuances of accessing the AX1800 settings, including alternative methods through the mobile application and solving typical problems. We will take a detailed look at each step so that even a beginner can set up a router without risking breaking the network.

Important: Xiaomi AX1800 Supports two modes of operation – router and access point (AP). The instructions below are relevant for both modes, but in some cases (for example, when connecting to another router) additional setup may be required. IP-addressing.

1. Preparation for entering the settings

Before you open the control panel, make sure your device (computer, smartphone or tablet) is connected to the Xiaomi AX1800 network.

• 📶 By Wi-Fi: Find the network with the default name (usually) Xiaomi_XXXX or MiWiFi_XXXX, where XXXX — unique characters) and connect using the password from the sticker on the bottom of the router.
• 🔌 Cable: Connect one of the LAN-port AX1800 (Yellow connectors) with your device's Ethernet port, which is a more stable method, especially if Wi-Fi is not working properly.

If you have previously changed your network name (SSID) or password and don't remember them, you'll have to reset your router to factory settings.

1. Turn the AX1800 on the network.
2. Find the Reset button on the back (usually recessed in the case).
3. Press and hold it for 10-15 seconds until the indicators start flashing orange.

⚠️ Warning: Reset will remove all user settings, including Wi-Fi passwords, tied devices and parental controls.

Also check that your device has a VPN or proxy disabled, which can block access to the router’s local network. If you use an antivirus with a network protection feature (such as Kaspersky or Avast), temporarily disable it.

2. Basic method: login via browser

The most universal method is to use a web interface.

1. Open any browser (Chrome, Firefox, Edge or Safari).
2. Enter one of the address bars IP-192.168.31.1 is the primary address for most Xiaomi routers. miwifi.com is an alternative domain (opts if unchanged) DNS-192.168.0.1 - backup address (rarely used in the AX1800).

Enter

If the page does not open, try the following:

• 🔄 Update the page (F5 Ctrl+R).
• 🧹 Clear the browser cache or try another browser.
• 🔍 Make sure your device is connected to the correct network (not your neighbor or mobile internet).

Once you've successfully connected, you'll see an authorization window, and the default data is the following:

⚠️ Warning: If you've previously changed your password to log into the control panel and forgot it, resetting the router to factory settings is the only way to restore access. Wi-Fi password and admin password are different data! AX1800|Correctness of the input IP-address|Absence VPN/proxy|Browser performance (try another one)|Ping to router (team) `ping 192.168.31.1` into CMD)--> 3. Alternative method: Mi Wi-Fi app If the web interface is not available or you prefer to control the router from your smartphone, use the official Mi Wi-Fi app (formerly Mi Router), which is available for Android and iOS and offers a user-friendly interface with translation into Russian. Download the application from official sources: 🤖 Google Play for Android). 🍎 App Store (for App Store) iPhone/iPad). After installation: Open Mi Wi-Fi and allow access to the location (necessary to search for a router on the local network). AX1800 — tap on its name. Enter the administrator password (default admin or sticker). Confirm the connection: 📱 Convenient mobile interface with adaptive design. 🌐 Automatic translation into Russian (in the web version you need to choose manually). 🔔 Notifications of new firmware and security threats, but there are also disadvantages: some advanced settings (for example, Port Forwarding or Port Forwarding). VLAN) It can be hidden in the mobile version. For complete control, it is better to combine the application with the web interface. 📊 How do you usually configure a router?Through a browser on a PC Through the Mi Wi-Fi app Through both options I do not configure myself 4. Solving Access Problems If You Entered It Correctly IP-Address and password, but login to settings is still not possible, check the following points: 4.1. Router does not respond to ping Open command line (Win) + R → enter cmd → Enter) and execute the command: ping 192.168.31.1 If no answers are available (the specified node is not available), the problem may be in the: 🔌 Router power: check that the power cable is tightly connected and the indicator on the front panel is blue (not orange). 🔄 Network card: Try another cable or port on the router. 🛠️ Hardware failure: If the indicators do not burn at all, repair may be required. 4.2. The authorization page does not load If the ping passes (there are answers), but the browser shows an error (ERR_CONNECTION_REFUSED Or a blank page, try it: 🔒 Disable Windows Firewall or Antivirus. 📥 Clean up DNS-cache by command: ipconfig /flushdns 🌍 Use the other DNS (for example, 8.8.8.8 Google). 4.3. Inappropriate. IP-Address If the router is running on the access point mode (AP) Or connected to another router, its local IP may differ 192.168.31.1. To find out the current address: On Windows: perform in CMD: ipconfig Look for the main gateway line in the block with an active connection. macOS/Linux: Use the command: netstat -rn | grep default In mode AP Xiaomi router AX1800 may receive IP from the main router (for example, 192.168.1.100). In this case, to access its settings, use the address listed on the main router as "connected device." How to reset if you forgot your password? If you can't log in to the control panel because of a lost password, perform a full reset: 1. Press and hold the Reset button on the back of the router 10–15 seconds. 2. Wait for the reboot (the indicators flash orange, then light up blue). 3. Connect to a Wi-Fi network with a name Xiaomi_XXXX (password). 4. Enter in the browser `192.168.31.1` and use the default login/password (`admin`/`admin`). ⚠️ After reset, all settings (including Wi-Fi and guest network passwords) will be deleted! 5. Navigation on the control panel After a successful login, you will see the main page with an overview of the state of the network. AX1800 divided into several key sections: 📊 Status: information about connected devices, Internet speed and working time. 🔄 Internet (Internet): Connection type setting (PPPoE, DHCP, static IP). 📶 Wi-Fi (Wi-Fi): Network Management 2.4 GHz and 5 GHz, change SSID and password. 🔒 Security: Firewall setting, filtration MAC-Addresses and Parental Controls. ⚙️ Additional (Advanced): Extended parameters (DDNS, port forwarding, VPN). For beginners, the following functions are useful: 🔄 Quick Setup: Original Configuration wizard (available at first login). 📱 Mi Wi-Fi App: synchronization with mobile application for remote management. 🔄 Firmware Update: Check and install the latest software. Please see the System Tools section. You can: Change the Admin Password. Backup & Restore. Reboot the router). ⚠️ Note: Change of settings in Advanced section → Network → LAN (for example, IP-Router addresses may result in loss of access to the control panel. Without experience, it is not recommended to edit these settings. 💡If the interface is in Chinese, switch the language in the upper right corner (flag) 🇨🇳 → 🇬🇧 or 🇷🇺). In the mobile application, the language changes automatically according to the settings of the smartphone. 6. Frequent errors and their correction Even after successful login, users face typical problems. Consider the most common: Error Possible reason Solution Not open page 192.168.31.1 IP-The router address has been changed Find out the current IP via ipconfig (see para. section 4.3) Error "Incorrect password" Admin password changed and forgotten Reset router button Reset Interface in Chinese without the possibility of changing language Outdated firmware Update the software in the System Tools section → Firmware Update No access to some sections (e.g. Port Forwarding) Restrictions in the mobile application Use the web interface from PC If after updating the firmware router began to work unstable (for example, breaks the connection or overheats), roll back to the previous version: Download the old firmware from Xiaomi's official website. Go to System Tools → Firmware Update → Manual Update. Download the firmware file and wait until the process is complete (don't turn off the router!). Important: Firmware rollback may result in the loss of some features added in newer versions. Use this method only in case of critical crashes. 💡Before you update your firmware, disconnect all devices from the router other than the one you're running the procedure from. 7. Security: How to Protect the Control Panel by Default Xiaomi AX1800 Uses standard data for entry (admin/admin), To secure the router: Change the admin password: Go to System Tools → Modify Login Password: Create a complex password (minimum) 8 Disable remote access (if not used): In Advanced → Remote Management set the switch to Off position. Update the firmware to the latest version (see section) 5). Also recommended: 🔒 Insert firewall (Security) → Firewall) and configure filtering by MAC-address. 📡 Shut down. WPS (Vulnerability to Reaver attacks: Wi-Fi → WPS Settings. 🔄 Regularly check the list of connected devices (Status) → Client List for unknown gadgets: If you suspect that the router is already compromised (for example, you see unusual activity on the network), perform a full reset and configure it again from scratch. FAQ: Answers to popular questions Can I go to the settings of Xiaomi AX1800 No. To access the control panel, your device must be connected to the router either via Wi-Fi or cable, except if Remote Management was previously configured, but it is not secure and is disabled by default. Why does the router not give out the Internet after reset? Reset removes the connection settings to the provider (for example, PPPoE data). You need to reconfigure the Internet in the Internet section using data from the contract with the provider (login, password, connection type). How to turn on Russian in the web interface? In the upper right corner of the control panel, click on the flag 🇨🇳 or 🇬🇧 and choose 🇷🇺 If you don't have an option, upgrade your router firmware to the latest version. AX1800 Telegram or voice assistant? Direct control via Telegram or Alice/Google Assistant is not available, but you can: Use the Mi Wi-Fi App for basic features (on/off Wi-Fi, guest network) Set up integration with Xiaomi Home to monitor connected devices (requires a Mi Account). Extended management (e.g., rebooting on schedule) will require third-party solutions like Home Assistant. Where to find a login and password if the sticker is erased? If the data from the sticker on the bottom of the router is not readable, try: Standard combinations: admin/admin or leave the login field empty. If not, reset with the Reset button (see Section 1). For new models, the admin password may match the default Wi-Fi password (last 8 characters). MAC-router).